NISSAN NV200 2019 Owners Manual

button located on the
steering wheel. When prompted, speak the
command for the system you wish to acti-
vate. The command given is picked up by
the microphone and performed when it is
properly recognized. NISSAN Voice Recog-
nition will provide a voice response as well
as a message in the center display to in-
form you of the command results.
USING THE SYSTEM
Initialization
When the ignition switch is in the ON posi-
tion, NISSAN Voice Recognition is initialized,
which takes a few seconds. When com-
pleted, the system is ready to accept voice
commands. If the
button is pressed
before the initialization completes, the sys-
tem will announce: Recognition Sys-
tem not ready. Please wait.Ž
Giving voice commands
1. Press thebutton.
2. The system announces: say a
category like phone or a command like
points of interest followed by a brand
nameŽ. A list of available commands is
then spoken by the system.
3. Af ter the tone sounds and the face icon
on the display changes, speak a com-
mand. Available commands are dis-
cussed in this section.4. Voice and display feedback are pro-
vided when the command is accepted.
 If the command is not recognized, the
system announces: not
recognizedŽ. Repeat the command in a
clear voice.
 If you want to cancel the command or
go back to the previous menu of com-
mands, press the
button. The sys-
tem will announce: voice
recognitionŽ or backŽ depending on
the current menu level.
 Press the BACK button on the control
panel to move back through the menus
displayed on the screen.
 If you want to adjust the volume of the
voice feedback, use the volume control
switches on the steering wheel or the
volume knob on the control panel.
 The voice command screen can also be
accessed using the control panel dis-
play:
1. Press the [
] button.
2. Select the CommandsŽ key.
LHA4437
NISSAN VOICE RECOGNITION
SYSTEM

LHA2780

button.
2. Say and then a name in the ve-
hicle phonebook to call that entry. Oth-
erwise, say to access various
phone commands.
If the Bluetooth® has been set to Ž, the
system announces: is off.
Would you like to turn Bluetooth® on?Ž
If no phone is connected to the system and
the vehicle is stationary, the system an-
nounces: is no phone connected.
Would you like to connect a phone now?Ž
Say to connect a phone. All further
Bluetooth® Hands-Free Phone System
voice commands are only available if a
phone is connected.
If a phone is connected and Bluetooth® is
set to the following voice commands
are available:
 Call (a name)
Speak the name of the contact in
which you are trying to call. System willconfirm correct contact. Say to
initiate dialing.
 Dial Number
Allows for up to 24 digits to be dialed.
Af ter the number is entered, say
to initiate dialing. Say to
correct the number entered. Say
BackŽ to return to the main menu.
 List Phonebook
Starting with the first alphabetical en-
try in the vehicle phonebook, the sys-
tem prompts for an additional com-
mand. Say to call the number of
the phonebook entry. Say TextŽ
to send a text message to the number
of the phonebook entry. Say En-
tryŽ to skip to the next alphabetical en-
try in the vehicle phonebook, where
the same options will then be available.
 Recent Calls
The system prompts for an additional
command. Say CallsŽ,
ing CallsŽ or CallsŽ to display
a list of such calls on the screen.
Speak the number of the entry dis-
played on the screen to dial thatnumber or say PageŽ to view en-
tries on the next page (if available).
 Redial
Redials the last called number.
 Read Text
Reads an incoming text message. For
additional information, refer to
Hands-Free Phone Sys-
tem with Navigation SystemŽ in this
section.
 Send Text
Sends a text message. For additional
information, refer to
Hands-Free Phone System with Navi-
gation SystemŽ in this section.
 Select Phone
The system replies use manual
controls to continueŽ. Use manual con-
trols to change the active phone from
among the listed phones connected
to the vehicle.
For additional information, refer to
Hands-Free Phone System
with Navigation SystemŽ in this section.
4-88Monitor, climate, audio, phone and voice recognition systems

button.
2. Say
3. Speak a command from the following
available commands:
 Play (AM, FM, etc.)
Allows user to select radio band Tune AM (number)
Allows user to tune directly to a desired
AM frequency
 Tune FM (number)
Allows user to tune directly to a desired
FM frequency
 SXM channel (number)
Allows user to tune directly to a desired
SXM station (if so equipped)
 CD Track (number)
Allows user to select track to be played
 Play Song (name)
Allows user to select song name to be
played
 Play Artist (name)
Allows user to select artist to be played
 Play Album (name)
Allows user to select album name to
be played
For additional information, refer to
systemŽ in this section.
INFORMATION VOICE COMMANDS
The following voice commands are avail-
able for the information functions of the
Navigation System:
 Traffic
 Fuel Prices
 Stocks
 Movie Listings
 Current Weather
 Weather Map
 5„dayForecast
 6 „ hour Forecast
For additional information, refer to the
separate NissanConnect® Manual.
MY APPS VOICE COMMANDS
Many Apps can be accessed using this
voice command. For additional informa-
tion, refer to Mobile AppsŽ
in this section.
Monitor, climate, audio, phone and voice recognition systems4-89

Symptom/error message Solution
The system responds
Not RecognizedŽ or the system fails
to recognize the command
correctly.1. Ensure that the command format is valid. Use the CommandsŽ or Can I Say?Ž command under the
menu.
2. Speak clearly without pausing between words and at a level appropriate to the ambient noise level.
3. Ensure that the ambient noise level is not excessive (for example, with the windows open or the defroster on).
NOTE:
If it is too noisy to use the phone, it is likely that voice commands will not be recognized.
4. If optional words of the command have been omitted, then the command should be tried with these in place.
4-90Monitor, climate, audio, phone and voice recognition systems