oil change NISSAN PULSAR 2014 Owners Manual


> (GLW   0RGHO &$@
6-4
In case ofemergency
SCE0504
WARNING:
. Besure toread andfollow theinstructions in
this section.
. DO NOTGET UNDER AVEHICLE THATIS
SUPPORTED BY A JACK .
. Never useajack which isnot provided with
your vehicle.
. The jack, which isprovided withyour vehicle,
is designed onlytolift your vehicle duringa
tire change. Donot use thejack provided
with your vehicle onother vehicles.
. Never jackupthe vehicle atalocation other
than thejack -uppoint thatisspecified.
. Never liftthe vehicle morethannecessary.
. Never useblocks onorunder thejack.
. Never startorrun theengine whilethe
vehicle ison the jack. Thevehicle maymove
suddenly, andthismay cause anaccident.
. Never allowpassengers toremain inthe
vehicle whilethetire isoff the ground. .
Besure toread thecaution labelattached to
the jack body before using.
1. Place thejack directly underthejack-up point as
illustrated sothat thetop ofthe jack contacts the
vehicle atthe jack-up point.
The jack should beplaced onfirm level
ground.
2. Align thejack head between thetwo notches
located atthe jack-up point ofeither thefront or
the rear section.
3. Fitthe groove ofthe jack head between the
notches asshown.
4. Loosen eachwheel nut,counterclockwise, oneor
two turns withthewheel nutwrench.
Do not remove thewheel nutsuntil thetire is
off the ground.
5. Carefully raisethevehicle untiltheclearance
between thetireand ground isachieved.
6. To lift the vehicle, securely holdthejack lever and
rod with both hands andturn thejack lever.
Removing tire
GUID-972 115C8-16B 3-429F-9DF 1-CC69110A0 0AF
1. Remove thewheel nuts.
2. Remove thedamaged tire.
CAUTION:
The tireisheavy. Besure thatyour feetareclear
from thetire and usegloves asnecessary to
avoid injury.
INST ALLING SPARE TIRE
GUID-028 A15EE-D4 CA-4435-AF C6-94D3C9E C3071
SCE0039
WARNING:
. Never usewheel nutswhich arenot provided
with your vehicle. Incorrect wheelnutsor
improperly tightenedwheelnutsmaycause
the wheel tobecome looseorcome off.This
could cause anaccident.
. Never useoilorgrease onthe wheel studs
or nuts. Thismaycause thewheel nutsto
become loose.
1. Clean anymud ordirt from thesurface between
the wheel andhub.
&RQGLWLRQ


> (GLW   0RGHO &$@
UNDERBOD Y
GUID-89AF 2A41-6CEA-44E0-80F 8-1B7040436 EE7
In areas where roadsaltisused inthe winter, itis
necessary toclean thevehicle's underbody regularlyin
order toprevent dirtand saltfrom building upand
causing theacceleration ofcorrosion onthe under-
body andsuspension.
Before thewinter andagain inthe spring, theunder-
seal must bechecked and,ifnecessary ,re-treated.
WHEELS
GUID-239 0DE90-52B 6-4CC6-847A-7DC2BA9 E7940
. Wash thewheels whenwashing thevehicle to
maintain theirappearance.
. Clean theinner sideofthe wheels whenthewheel
is changed orthe underside ofthe vehicle is
washed.
. Donot use abrasive cleaners whenwashing the
wheels.
. Inspect wheelrimsregularly fordents orcorrosion.
This maycause lossofpressure ordamage the
tire bead.
. NISSAN recommends thattheroad wheels be
waxed toprotect against roadsaltinareas where
it is used during winter.
ALUMINUM ALLOY WHEELS
GUID-1A54 676E-FE36-464E-B750-86EA828D F50B
W ash thewheels regularly withasponge dampened in
a mild soap solution, especially duringwinterinareas
where roadsaltisused. Thesaltresidue fromroad salt
could discolor thewheels ifit is not washed off
regularly .
CAUTION:
Follow thedirections belowtoavoid staining or
discoloring thewheels: .
Donot use acleaner thatuses strong acidor
alkali contents toclean thewheels.
. Donot apply wheel cleaners tothe wheels
when theyarehot. Thewheel temperature
should bethe same asambient temperature.
. Rinse thewheel tocompletely removethe
cleaner within15minutes afterthecleaner is
applied.
CHROME PARTS
GUID-A 28C0751-4F8 0-44DA-8C22-EFE406D2DF5D
Clean allchrome partsregularly withanonabrasive
chrome polishtomaintain thefinish.
GUID-E4C 0088E-D11B-4 28E-9FC8-BCF4B6D9231F
Occasionally removeloosedustfrom theinterior trim,
plastic partsandseats using avacuum cleanerorsoft
bristled brush.Wipethevinyl andleather surfaces with
a clean, softcloth dampened inmild soap solution,
then wipe clean withadry ,soft cloth.
Regular careandcleaning isrequired inorder to
maintain theappearance ofthe leather.
Before usinganyfabric protector, readthemanufac-
turer's recommendations. Somefabricprotectors
contain chemicals thatmay stain orbleach theseat
material.
Use asoft cloth dampened onlywith water toclean the
meter andgauge lenscovers.
CAUTION:
. Never usebenzine, thinnerorany similar
material.
. Small dirtparticles canbeabrasive and
damaging toleather surfaces andshould be
removed promptly. Donot use saddle soap,
car waxes, polishes, oils,cleaning fluids,
solvents, detergents orammonia-based
cleaners asthey damage thenatural leather
finish.
. Never usefabric protectors unlessrecom-
mended bythe manufacturer.
. Donot use glass orplastic cleaner onmeter
or gauge lenscovers. Itmay damage the
lens covers.
Appearan ceand care
7-3
CLEANING
INTERIOR
&RQGLWLRQ


> (GLW   0RGHO &$@
Tires*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepressure withagauge oftenandalways
prior tolong distance trips.Adjust thepressure inall
tires, including thespare, tothe pressure specified.
Check carefully fordamage, cutsorexcessive wear.
Tire rotation*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
In the case thatTwo-Wheel Drive(2WD) andfront &
rear tires aresame size;Tires should berotated every
10,000 km(6,000 miles).Tires marked withdirectional
indicators canonly berotated between frontandrear.
Make surethatthedirectional indicatorspointinthe
direction ofwheel rotation afterthetire rotation is
completed.
In the case thatFour-Wheel Drive(4WD) andfront &
rear tires aresame size;Tires should berotated every
5,000 km(3,000 miles).Tires marked withdirectional
indicators canonly berotated between frontandrear.
Make surethatthedirectional indicatorspointinthe
direction ofwheel rotation afterthetire rotation is
completed.
In the case thatfront tiresaredifferent sizefrom rear
tires; Tirescannot berotated.
However, thetiming fortire rotation mayvaryaccording
to your driving habitsandtheroad surface conditions.
Tire Pressure Monitoring System(TPMS)trans-
mitter components (ifequipped) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Replace theTPMS transmitter grommetseal,valve
core andcap when thetires arereplaced duetowear
or age.
Wheel alignment andbalance:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
If the vehicle shouldpulltoeither sidewhile driving on
a straight andlevel road, orifyou detect uneven or
abnormal tirewear, theremaybeaneed forwheel
alignment. Ifthe steering wheelorseat vibrates at
normal highway speeds,wheelbalancing maybe needed.
Windshield:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Clean thewindshield onaregular basis.Check the
windshield atleast every sixmonths forcracks orother
damage. Repairasnecessary .
Wiper blades*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check forcracks orwear ifnot functioning correctly.
Inside vehicle
GUID-55 4469D2-12 96-4F49-B7A0 -0A8847FB7455
The maintenance itemslistedhereshould bechecked
on aregular basis,suchaswhen performing periodic
maintenance, cleaningthevehicle, etc.
Accelerator pedal:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepedal forsmooth operation andmake sure
that thepedal doesnotcatch orrequire uneven effort.
K eep thefloor mats away fromthepedal.
Brake pedal*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepedal forsmooth operation andmake sure
that itis the proper distance fromthefloor matwhen
depressed fully.Check thebrake booster function. Be
sure tokeep thefloor mats away fromthepedal.
Parking brake*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check theparking brakeoperation regularly.Check
that thelever (ifequipped) orthe pedal (ifequipped)
has theproper travel.Alsomake surethatthevehicle is
held securely onafairly steep hillwhen onlythe
parking brakeisapplied.
Seat belts:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatallparts ofthe seat beltsystem (for
example, buckles,anchors, adjusters andretractors)
operate properly andsmoothly ,and areinstalled
securely .Check thebelt webbing forcuts, fraying,
wear ordamage. Steering
wheel:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check forchanges inthe steering condition, suchas
excessive play,hard steering orstrange noises.
Warning lightsandchimes:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Make surethatallwarning lightsandchimes are
operating properly.
Windshield defogger:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thattheaircomes outofthe defogger outlets
properly andingood quantity whenoperating the
heater orair conditioner.
Windshield wiperandwasher*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatthewipers andwasher operate properly
and that thewipers donot streak.
Under hoodandvehicle
GUID-E5D 10961-EA14 -4A37-B87E- 268783A0FC3 8
The maintenance itemslistedhereshould bechecked
periodically (forexample, eachtimeyoucheck the
engine oilorrefuel) .
Battery*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Except formaintenance freebattery ,check thefluid
level ineach cell.Itshould bebetween theªUPPERº
and ªLOWERº lines.Vehicles operated inhigh
temperatures orunder severe conditions require
frequent checksofthe battery fluidlevel.
Brake (andclutch) fluidlevel(s)*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
For Manual Transmission (MT)model; makesurethat
the brake andclutch fluidlevels arebetween the
ªMAXº andªMINº linesonthe reservoirs.
Except forManual Transmission (MT)model; make
sure thatthebrake fluidlevel isbetween theªMAXº
and ªMINº linesonthe reservoir.
Maintenan ceand do-it-you rself
8-3
&RQGLWLRQ


> (GLW   0RGHO &$@
GUID-B1 20ADA3-D0 3C-49B1-B529-7A274B D909D0
CHECKING ENGINEOILLEVEL
GUID-7F B3D707-0 60C-4B57-B BE7-3BDD80ACE30 5
SDI1993
T ype A
SDI2721
T ype B
1. Park thevehicle onalevel surface andapply the
parking brake.
2. Start theengine andwarm itup until theengine
temperature reachesthenormal operating tem-
perature (approximately 5minutes) .
3. Stop theengine.
4. Wait atleast 10minutes forthe engine oiltodrain
back tothe oilpan.
5. Remove thedipstick andwipe itclean. 6.
Reinsert thedipstick allthe way.
7. Remove thedipstick andcheck theoillevel. It
should bewithin therange
*
C
.
8. Ifthe oillevel isbelow
*
A
, remove theoilfiller cap
and pour therecommended oilinto theopening.
Do not overfill
*
B
.
When fillingtheengine oil,donot remove
the dipstick.
9. Recheck theoillevel withthedipstick.
It is normal toadd some oilbetween oil
maintenance intervalsorduring thebreak -in
period, depending onthe severity ofoperat-
ing conditions.
CAUTION:
The oillevel should bechecked regularly.
Operating yourvehicle withaninsufficient
amount ofoil can damage theengine, andsuch
damage isnot covered bythe warranty.
CHANGING ENGINEOILAND OILFILTER
GUID-BFC63 F3B-A179-42CF-BDF1-B 43386889AD1
WARNING:
. Used oilmust bedisposed ofproperly. Never
pour ordump oilinto theground, canals,
rivers, etc.It should bedisposed ofatproper
waste facilities. NISSANrecommends hav-
ing your oilchanged byaNISSAN dealer.
. Be careful nottoburn yourself, asthe
engine oilmay behot.
. Prolonged andrepeated contactwithused
engine oilmay cause skincancer.
. Avoid directskincontact withused oil.If
contacted, washthoroughly withsoap or hand
cleaner andplenty ofwater assoon as
possible.
. Store usedengine oilinmarked containers
out ofthe reach ofchildren.
1. Park thevehicle onalevel surface andapply the
parking brake.
2. Start theengine andwarm itup until theengine
temperature reachesthenormal operating tem-
perature (approximately 5minutes) .
3. Stop theengine.
4. Wait atleast 10minutes forthe engine oiltodrain
back tothe oilpan.
5. Raise andsupport thevehicle usingasuitable
floor jackandsafety jackstands.
.
Place thesafety jackstands underthevehicle
jack -up points.
.
A suitable adaptershouldbeattached tothe
jack stand saddle.
6. For HR16DE enginemodel,remove theplastic
engine undercover.
.
Remove thebolts andplastic clipsfromthe
undercover.
Maintenan ceand do-it-you rself
8-9
ENGINE
OIL
&RQGLWLRQ


> (GLW   0RGHO &$@
8-10
Maintenance anddo-it-yours elf
Engine oiland filter
GUID-5F 013F78-E E34-4C18-B FFB-79938 408A1A2
JVM0161X
MRA8DE engine model
SDI2652
MR16DDT engine model
JVM0081X
MRA8DE andMR16DDT engine model
SDI2722
HR16DE enginemodel
*
1
Oil filler cap
*
2
Oil drain plug
*
3
Oil filter
1. Place alarge drainpanunder thedrain plug.
2. Remove thedrain plugwithawrench.
3. Remove theoilfiller capand completely drainthe
oil.
If the oilfilter isto be changed, removeand
replace itat this time.
CAUTION:
Waste oilmust bedisposed ofproperly. Check
your local regulations.
4. Loosen theoilfilter withanoilfilter wrench.
5. Remove theoilfilter byturning itby hand.
6. Wipe theengine oilfilter mounting surfacewitha
clean cloth.
Be sure toremove anyoldgasket remaining onthe
mounting surface.
7. Apply newengine oiltothe gasket ofthe new oil
filter.
8. Screw inthe oilfilter untilaslight resistance isfelt
and then tighten anadditional 2/3ofaturn to
secure thefilter.
Oil filter tightening torque:
15 to20 N´m
(1.5 to2.0 kg-m, 11to15 ft-lb)
9. Clean andreinstall thedrain plugandnew washer.
Securely tightenthedrain plugwithawrench. Do
not use excessive force.
Drain plugtightening torque:
29 to39 N´m
(3.0 to4.0 kg-m, 22to29 ft-lb)
10. Refill therecommended engineoiland quantity .
(See ªRecommended fluids/lubricantsandcapa-
citiesº (P.9-2) .)
When fillingtheengine oil,donot remove
the dipstick (exceptforHR16DE engine
model) .
11. Securely installtheoilfiller cap.
&RQGLWLRQ