engine NISSAN PULSAR 2016 Owner's Guide


> (GLW   0RGHO &$@
5-4
Starting anddriving
GUID-365 EE49C-5FF 9-4447-845A-3881038 C5420
Driving yourvehicle tofitthe circumstances isessential
for your safety andcomfort. Asadriver, youshould be
the one who knows besthowtodrive inthe given
circumstances.
ENGINE COLDSTART PERIOD
GUID-B8 9C453D-A 996-4A1A-A8 96-4FC3520E6BFC
Due tothe higher engine speeds, whentheengine is
cold, extracaution mustbeexercised whenselecting a
gear during theengine warm-up periodafterstarting
the engine.
L OADING LUGGAGE
GUID-C66 3B3F6-8EAA- 46C6-9228-B 3141F69D6D3
Loads andtheir distribution andtheattachment of
equipment (couplingdevices,roofluggage carriers,
etc.) willconsiderably changethedriving character-
istics ofthe vehicle. Your driving styleandspeed must
be adjusted according tothe circumstances.
DRIVING INWET CONDITIONS
GUID-3D DDCE8B-46F7 -4220-938D-F02C21034A4A
. Avoid accelerating orstopping suddenly.
. Avoid sharpturning orlane changing suddenly.
. Avoid following tooclose tothe vehicle infront.
When watercovers theroad surface withwater
puddles, smallwater streams, etc.,reduce speedto
prevent hydroplaning whichcancause skidding and
loss ofcontrol. Worn tires willincrease thisrisk.
DRIVING INWINTER CONDITIONS
GUID-393 9347B-E44 6-4695-87D1-257AFA202DC2
. Drive cautiously .
. Avoid accelerating orstopping suddenly.
. Avoid sharpturning orlane changing suddenly.
. Avoid sudden steering.
. Avoid following tooclose tothe vehicle infront.
GUID-91D DB153-CB CA-454D-B 139-A71B18FD2EDC
WARNING:
Never remove thekey orturn theignition switch
to the ªLOCKº position whiledriving. Thesteer-
ing wheel willlock andcould cause thedriver to
lose control ofthe vehicle. Thiscould result in
serious vehicledamage orpersonal injury.
CONTINUOUSL YVARIABLE TRANSMIS-
SION (CVT)
GUID-54 525C04-496 D-421C-8752-6B511BA 7402C
SSD0392
The ignition lockisdesigned sothat theignition switch
cannot beturned tothe ªLOCKº position untiltheshift
lever ismoved tothe ªPº (Park) position. Whenmoving
the ignition switchtothe ªLOCKº position, toremove
the key from theignition switch,makesuretheshift
lever isin the ªPº (Park) position.
When theignition switchcannot beturned tothe
ªL OCKº position:
1. Move theshift lever tothe ªPº (Park) position.
2. Turn theignition switchslightly inthe ªONº
direction.
3. Turn theignition switchtothe ªLOCKº position. 4.
Remove thekey.
If the ignition switchisturned tothe ªLOCKº position,
the shift lever cannot bemoved fromtheªPº (Park)
position. Theshift lever canbemoved ifthe ignition
switch isin the ªONº position withthefoot brake pedal
depressed.
The ªOFFº position
*
1
is between theªLOCKº and
ª ACCº positions, althoughitis not marked onthe
ignition switch.
MANUAL TRANSMISSION (MT)
GUID-21 B70D8F-F0 98-475A-A7 7E-979553 F48594
SSD0503
The ignition switchincludes adevice thathelps
prevent accidental removalofthe key while driving.
The keycan only beremoved whentheignition switch
is in the ªLOCKº position.
T o turn theignition switchtothe ªLOCKº position from
the ªACCº orªONº position, turnthekey tothe ªOFFº
position, pushthekey in,then turnthekey tothe
ªL OCKº position.
The ªOFFº position
*
1
is between theªLOCKº and
ª ACCº positions, althoughitis not labeled onthe
ignition switch.
CARE WHEN DRIVING IGNITION
SWITCH(model without
Intelligent Keysystem)
&RQGLWLRQ


> (GLW   0RGHO &$@
STEERING LOCK
GUID-84FC5F 17-E3C7-4BE1-842B-2 338DC8B9E85
T o lock steering wheel
GUID-643 D9CDC-84 45-49BB-8146-1F81F862C0B9
1. Turn theignition switchtothe ªLOCKº position.
2. Remove thekey from theignition switch.
3. Turn thesteering wheel1/6ofaturn clockwise
from thestraight upposition.
T o unlock steering wheel
GUID-F9918 49F-1987-47 3E-AFAD-235CD 32C3712
1. Insert thekey into theignition switch.
2. Gently turntheignition switchwhilerotating the
steering wheelslightly rightandleft.
KEY POSITIONS
GUID-95C A75D5-0D2E -4FAF-BC0 D-63E3D92 C30B8
L OCK (0)
GUID-144 974C4-67B 8-4F45-92DA- 6954532EDEFE
The ignition keycan only beremoved atthis position.
The steering lockcanonly belocked atthis position.
OFF (1)
GUID-54 D824D0-1B74 -4475-84F5-CA80FB23D19C
The engine isturned offwith thesteering wheel
unlocked.
ACC (2)
GUID-17 E1619A-16C2 -4F88-A958-D19A38830 78C
The electrical accessory poweractivates withoutthe
engine turnedon.
ON (3)
GUID-8FAE5841-E613-460B-A9 14-0927C1C5B9A6
The ignition systemandtheelectrical accessory power
activate withouttheengine turnedon.
ST ART (4)
GUID-16D 5423F-AB9 6-440A-A9B2 -60948BDBB14C
The engine starteractivates andtheengine willstart.
The ignition switch,whenreleased, willautomatically
turn tothe ªONº position.
CAUTION:
As soon asthe engine hasstarted, releasethe
ignition switchimmediately.
GUID-8D8 CC42A-947 4-401D-AE63-E7B674 B40563
PRECAUTIONS ONPUSH-BUTT ONIGNI-
TION SWITCHOPERA TION
GUID-135 62CA9-9E1 B-4EA6-B47 6-DA4BA15F7D32
WARNING:
Do not operate thepush-button ignitionswitch
while driving thevehicle exceptinan emergency.
(The engine willstop when theignition switchis
pushed 3consecutive timesorthe ignition
switch ispushed andheld formore than2
seconds.) Thesteering wheelwilllock andcould
cause thedriver tolose control ofthe vehicle.
This could result inserious vehicledamage or
personal injury.
Before operating thepush-button ignitionswitch,be
sure tomove theshift lever tothe ªPº (Park) position
(for Continuously Variable Transmission model)orthe
shift lever tothe ªNº (Neutral) position(forManual
T ransmission model).
INTELLIGENT KEYSYSTEM
GUID-771FA3AD-C30C-4693-9 8E4-B9AE610D746B
The Intelligent Key system canoperate theignition
switch without takingthekey outfrom yourpocket or
bag. Theoperating environment and/orconditions may
affect theIntelligent Key system operation.
CAUTION:
. Besure tocarry theIntelligent Keywith you
when operating thevehicle.
. Never leavetheIntelligent Keyinside the
vehicle whenyouleave thevehicle.
. Ifthe vehicle battery isdischarged, the
ignition switchcannot beswitched from
the ªLOCKº position, andifthe steering lock
is engaged, thesteering wheelcannot be
moved. Chargethebattery assoon as
Starting anddriving
5-5
PUSH-BUT
TON IGNITION SWITCH
(model withIntelligent Keysystem)
&RQGLWLRQ


> (GLW   0RGHO &$@
5-6
Starting anddriving
possible. (SeeªJump startingº (P.6-5) .)
Operating range
GUID-80A4 4E43-0A1B -4ABB-A7E6-B D571734D53 C
SSD0436
The Intelligent Key can only beused forstarting the
engine whentheIntelligent Key iswithin thespecified
operating range
*
1
.
When theIntelligent Key battery isalmost discharged
or strong radiowaves arepresent neartheoperating
location, theIntelligent Key system's operating range
becomes narrowerandmay notfunction properly.
If the Intelligent Key iswithin theoperating range,itis
possible foranyone, evensomeone whodoes notcarry
the Intelligent Key ,to push theignition switchtostart
the engine.
. The luggage roomareaisnot included inthe
operating range,buttheIntelligent Keymay
function.
. Ifthe Intelligent Key isplaced onthe instrument
panel, insidetheglove box,door pocket orthe
corner ofthe interior compartment, theIntelligent
K ey may notfunction.
. Ifthe Intelligent Key isplaced nearthedoor or
window outsidethevehicle, theIntelligent Key
may function.
Continuously Variable Transmission (CVT)
model
GUID-59131E CE-A47C-4849-A212-5FF7051D7462
The ignition lockisdesigned sothat theignition switch
cannot beswitched tothe ªLOCKº position untilthe
shift lever ismoved tothe ªPº (Park) position. When
pushing theignition switchtothe ªOFFº position, make
sure theshift lever isin the ªPº (Park) position.
When theignition switchcannot beswitched tothe
ªL OCKº position:
1. Move theshift lever tothe ªPº (Park) position.
2. Push theignition switchtothe ªOFFº position.
3. Open thedoor. Theignition switchwillchange to
the ªLOCKº position.
If the ignition switchisswitched tothe ªLOCKº
position, theshift lever cannot bemoved fromtheªPº
(Park) position. Theshift lever canbemoved ifthe
ignition switchisin the ªONº position withthefoot
brake depressed.
STEERING LOCK
GUID-E05 63F6E-C5FD- 4C6A-83D7-9D 4CAE048AA9
The ignition switchisequipped withananti-theft
steering lockdevice.
T o lock steering wheel
GUID-199 0FCB9-1E4 5-4067-918 5-B54F6548 9D5D
1. Push theignition switchtothe ªOFFº position
where theignition switchposition indicator willnot
illuminate.
2. Open orclose thedoor. Theignition switchturns
to the ªLOCKº position.
3. Turn thesteering wheel1/6ofaturn tothe right or
left from thestraight upposition.
T o unlock steering wheel
GUID-836 CAB5B-2A97-4D4D-B A13-0D61A7DEAB3B
Push theignition switch,andthesteering wheelwillbe
automatically unlocked.
CAUTION:
. Ifthe battery ofthe vehicle isdischarged, the
push-button ignitionswitchcannot be
switched fromtheªLOCKº position.
. Ifthe ignition switchposition doesnot
change fromtheªLOCKº position, pushthe
ignition switchagainwhilerotating the
steering wheelslightly tothe right andleft.
IGNITION SWITCHPOSITIONS
GUID-787 88975-EF20-4EEC-9 BD9-C8FD 1F38789B
SSD0859
When theignition switchispushed withoutdepressing
the brake pedal (Continuously Variable Transmission
model) orthe clutch pedal(Manual Transmission
model) ,the ignition switchposition willchange as
follows:
. Push oncetochange toªACCº .
. Push twotimes tochange toªONº .
. Push three times tochange toªOFFº .
&RQGLWLRQ


> (GLW   0RGHO &$@
. Push fourtimes toreturn toªACCº .
. Open orclose anydoor toreturn toªLOCKº when
in the ªOFFº position.
The indicator light
*
A
on the ignition switchillumi-
nates whentheignition switchisin the ªACCº orªONº
position.
L OCK position
GUID-43425B BE-7F00-4ED4-A87 5-071702F2 842A
The ignition switchandsteering lockcanonly be
locked atthis position.
The ignition switchwillbeunlocked whenitis pushed
to the ªACCº position whilecarrying theIntelligent Key .
ACC position
GUID-202F5 141-00BE-47DC-B76C-7 268FE6DC636
The electrical accessory poweractivates atthis
position withouttheengine turnedon.
ON position
GUID-9FF5 AE68-135D-4 D67-8BBC-43E8DC881 23E
The ignition systemandtheelectrical accessory power
activate atthis position withouttheengine turnedon.
OFF position
GUID-81EA9 526-2AC3-4FF2-91B3 -F3E0BFFFA02D
The engine isturned offwith thesteering wheel
unlocked.
WARNING:
Never pushtheignition switchtothe ªOFFº
position whiledriving. Thesteering wheelmay
lock andcause thedriver tolose control ofthe
vehicle, resulting inserious vehicledamage or
personal injury.
CAUTION:
Do not leave thevehicle forextended periodsof
time when theignition switchisin the ªACCº or
ªONº position andtheengine isnot running. This
candischarge thebattery.
INTELLIGENT KEYBATTER YDISCHARGE
GUID-EC7 BC919-57B A-4B13-9C48-52E166 3770CA
SSD0860
If the battery ofthe Intelligent Key isdischarged, or
environmental conditionsinterferewiththeIntelligent
K ey operation, starttheengine according tothe
following procedure:
1. Continuously Variable Transmission (CVT)
model:
Move theshift lever tothe ªPº (Park) orªNº
(Neutral) position.
Manual Transmission (MT)model:
Move theshift lever tothe ªNº (Neutral) position.
2. Firmly depress thebrake pedal.
3. Touch theignition switchwiththeIntelligent Key
as illustrated. (Achime willsound.)
4. Push theignition switchwhiledepressing the
brake pedal (Continuously Variable Transmission
models) orclutch pedal(Manual Transmission
models) within10seconds afterthechime
sounds. Theengine willstart.
After step3is performed, whentheignition switchis
pushed withoutdepressing thebrake pedal (Con-
tinuously Variable Transmission models)orclutch pedal
(Manual Transmission models),the ignition
switch position willchange toªACCº .
NO TE:
. When theignition switchispushed tothe
ª ACCº orªONº position orthe engine is
started bythe above procedures, theIntel-
ligent Keysystem warning lightmayblink in
yellow evenifthe Intelligent Keyisinside
the vehicle. Thisisnot amalfunction. To stop
the warning lightfrom blinking, touchthe
ignition switchwiththeIntelligent Key
again.
. Ifthe Intelligent Keysystem warning lightin
the meter isblinking ingreen, replace the
battery assoon aspossible. (SeeªBatteryº
(P .8-18) .)
Starting anddriving
5-7
&RQGLWLRQ


> (GLW   0RGHO &$@
5-8
Starting anddriving
GUID-CBF21 064-B60B-405D-A4B8-F9 ACF8015B5A
1. Apply theparking brake.
2. Depress thefoot brake pedal.
3. Continuously Variable Transmission (CVT)
model:
Move theshift lever tothe ªPº (Park) orªNº
(Neutral) position.
The starter isdesigned tooperate onlywhen
the shift lever isin the proper position.
Manual Transmission (MT)model:
Move theshift lever tothe ªNº (Neutral) position,
and depress theclutch pedaltothe floor while
starting theengine.
The starter isdesigned tonot operate unless
the clutch pedalisdepressed.
4. Crank theengine withyour footoffthe accelerator
pedal byturning theignition switchtothe ªSTARTº
position.
5. Immediately releasetheignition switchwhenthe
engine starts.Ifthe engine starts,butfails torun,
repeat theabove procedures.
.
If the engine isvery hard tostart inextremely
cold weather orwhen restarting, depressthe
accelerator pedalalittle (approximately 1/3to
the floor) ,hold itand then crank theengine.
Release theaccelerator pedalwhentheengine
starts.
.
If the engine isvery hard tostart because itis
flooded, depresstheaccelerator pedalallthe
way tothe floor andhold it.Crank theengine
for 5-6 seconds. Aftercranking theengine,
release theaccelerator pedal.Cranktheengine
with your footoffthe accelerator pedalby
turning theignition switchtoSTART .Release
the ignition switchwhentheengine starts.Ifthe
engine starts,butfails torun, repeat theabove procedure.
CAUTION:
. Donot operate thestarter formore than15
seconds atatime. Ifthe engine doesnot
start, turntheignition switchoffand wait 10
seconds beforecranking theengine again.
Otherwise, thestarter couldbedamaged.
. Ifitbecomes necessary tostart theengine
with abooster batteryandjumper cables,
the instructions andcautions contained in
the ª6.Incase ofemergencyº sectionshould
be carefully followed.
6. Allow theengine toidle foratleast 30seconds
after starting theengine towarm-up. Driveat
moderate speedsforashort distance first,
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
GUID-27 686CF6-E6E 5-4E98-9C0E-E33A1613D 9C9
1. Apply theparking brake.
2. Continuously Variable Transmission (CVT)
model:
Move theshift lever tothe ªPº (Park) orthe ªNº
(Neutral) position.
The starter isdesigned tooperate onlywhen
the shift lever isin the proper position.
Manual Transmission (MT)model:
Move theshift lever tothe ªNº (Neutral) position.
The starter isdesigned nottooperate unless
the clutch pedalisfully depressed.
The Intelligent Keymust becarried when
operating theignition switch.
3. Push theignition switchtothe ªONº position.
Depress thebrake pedal(CVTmodel) orthe
clutch pedal(MTmodel) andpush theignition
switch tostart theengine.
T o start theengine immediately ,push andrelease
the ignition switchwhiledepressing thebrake
pedal orclutch pedalwiththeignition switchin
any position.
4. Ifthe engine starts,butfails torun, repeat the
above procedures.
.
If the engine isvery hard tostart inextremely
cold weather orwhen restarting, depressthe
accelerator pedalalittle (approximately 1/3to
the floor) ,hold itand then crank theengine.
Release theaccelerator pedalwhentheengine
starts.
.
If the engine isvery hard tostart because itis
flooded, depresstheaccelerator pedalallthe
way tothe floor andhold it.Crank theengine
for 5-6 seconds. Aftercranking theengine,
release theaccelerator pedal.Cranktheengine
with your footoffthe accelerator pedalby
ST ARTING ENGINE (modelwithout
Intelligent Keysystem) ST
ARTING ENGINE (modelwith
Intelligent Keysystem)
&RQGLWLRQ


> (GLW   0RGHO &$@
turning theignition switchtoSTART .Release
the ignition switchwhentheengine starts.Ifthe
engine starts,butfails torun, repeat theabove
procedure.
CAUTION:
. Assoon asthe engine hasstarted, release
the ignition switchimmediately.
. Donot operate thestarter formore than15
seconds atatime. Ifthe engine doesnot
start, pushtheignition switchtothe ªOFFº
position andwait 10seconds beforecrank-
ing the engine again.Otherwise, thestarter
could bedamaged.
. Ifitbecomes necessary tostart theengine
with abooster batteryandjumper cables,
the instructions andcautions contained in
the ª6.Incase ofemergencyº sectionshould
be carefully followed.
5. Allow theengine toidle foratleast 30seconds
after starting theengine towarm-up. Driveat
moderate speedsforashort distance first,
especially incold weather.
CAUTION:
Do not leave thevehicle unattended whilethe
engine iswarming up.
6. To stop theengine, movetheshift lever tothe ªPº
(Park) position (CVTmodel) ormove theshift lever
to the ªNº (Neutral) position(MTmodel) ,apply the
parking brakeandpush theignition switchtothe
ªOFFº position.
GUID-FC 8DD999-53 2D-4255-B52B-8544BB F23419
DRIVING WITHCONTINUOUSL YVARI-
ABLE TRANSMISSION (CVT)
GUID-CA 3CA43B-2A 6A-4E78-941 9-61BAC1DD D7EF
The Continuously Variable Transmission (CVT)inyour
vehicle iselectronically controlledtoproduce maximum
power andsmooth operation.
The recommended operatingprocedures forthis
transmission areshown onthe following pages.Follow
these procedures formaximum vehicleperformance
and driving enjoyment.
WARNING:
Do not downshift abruptlyonslippery roads.
This maycause aloss ofcontrol.
CAUTION:
. The cold engine idlespeed ishigh, souse
caution whenshifting thetransmission into
a forward orreverse position beforethe
engine haswarmed up.
. Avoid revving upthe engine whilethe
vehicle isstopped. Thiscould cause unex-
pected vehicle movement.
. Never shifttoeither theªPº (Park) orªRº
(Reverse) positionwhilethevehicle ismov-
ing. This could cause serious damage tothe
transmission.
. Except inan emergency, donot shift tothe
ªNº (Neutral) positionwhiledriving. Coast-
ing with thetransmission inthe ªNº (Neutral)
position maycause serious damage tothe
transmission.
. Start theengine ineither theªPº (Park) or
ªNº (Neutral) position.Theengine willnot
start inany other position. Ifitdoes, have your
vehicle checked byaNISSAN dealer.
. Shift intotheªPº (Park) position andapply
the parking brakewhenatastandstill for
longer thanashort waiting period.
. Keep theengine atidling speed while
shifting fromtheªNº (Neutral) positionto
any driving position.
. When stopping thevehicle onanuphill
grade, donot hold thevehicle bydepressing
the accelerator pedal.Thefoot brake pedal
should bedepressed inthis situation.
Starting vehicle
GUID-9E5 839FD-C45 3-4C86-B65 8-6D40F7F1CF16
1. After starting theengine, fullydepress thefoot
brake pedalbefore moving theshift lever outofthe
ªPº (Park) position.
2. Keep thefoot brake pedaldepressed andmove
the shift lever toadriving position.
3. Release theparking brake,thefoot brake pedal,
and then gradually startthevehicle inmotion.
The CVT isdesigned sothe foot brake pedal
MUST bedepressed beforeshifting fromtheªPº
(Park) position toany driving position whilethe
ignition switchisin the ªONº position.
The shift lever cannot bemoved outofthe ªPº
(Park) position andinto anyofthe other
positions ifthe ignition switchisplaced inthe
ªLOCKº ,ªOFFº orªACCº position orifthe key is
removed.
CAUTION:
. DEPRESS THEFOOTBRAKE PEDAL-Shift-
ing the shift lever toªDº ,ªR º, ªL º or the
manual shiftmode without depressing the
foot brake pedalcauses thevehicle tomove
Starting anddriving
5-9
DRIVING
VEHICLE
&RQGLWLRQ


> (GLW   0RGHO &$@
5-10
Starting anddriving
slowly whentheengine isrunning. Make
sure thefoot brake pedalisdepressed fully
and thevehicle isstopped beforeshifting
the shift lever.
. MAKE SUREOFTHE SHIFT LEVER POSI-
TION -Make suretheshift lever isin the
desired position. ªDºand ªLºor manual shift
mode areused tomove forward andªRºto
back up.
. WARM UPTHE ENGINE -Due tothe higher
idle speeds whentheengine iscold, extra
caution mustbeexercised whenshifting the
shift lever intothedriving position immedi-
ately afterstarting theengine.
Shifting
GUID-22528B F3-29D9-403E-AE79-B EA15D2F63 FE
JVS0199X
With manual shiftmode (RHD model)
JVO0030X
Without manualshiftmode (LHD model)

Push thebutton
*
A
while depressing the
foot brake
pedal.

Push thebutton
*
A
.

Just move theshift lever.
WARNING:
. Apply theparking brakeifthe shift lever isin
any position whiletheengine isnot running.
Failure todo socould cause thevehicle to
move unexpectedly orroll away andresult in
serious personal injuryorproperty damage.
. Ifthe shift lever cannot bemoved fromthe
ªPº (Park) position whiletheengine is
running andthefoot brake pedalisde-
pressed, thestop lights maynotwork.
Malfunctioning stoplights couldcause an
accident injuringyourself andothers.
After starting theengine, fullydepress thefoot brake
pedal, pushtheshift lever button andmove theshift
lever outofthe ªPº (Park) position.
If the ignition switchisplaced inthe ªOFFº orªACCº
position forany reason whiletheshift lever isin any positions
otherthantheªPº (Park) position, theignition
switch cannot beplaced inthe ªLOCKº position.
If the ignition switchcannot beplaced inthe ªLOCKº
position, performthefollowing steps:
1. Apply theparking brake.
2. Place theignition switchinthe ªONº position
while depressing thefoot brake pedal.
3. Move theshift lever tothe ªPº (Park) position.
4. Models withIntelligent Keysystem:
Place theignition switchinthe ªOFFº position.
Models without Intelligent Keysystem:
Place theignition switchinthe ªLOCKº position.
P (Park) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Use thisposition whenthevehicle isparked orwhen
starting theengine. Makesurethatthevehicle is
completely stoppedandmove theshift lever into
the ªPº(Park) position. Applytheparking brake.
When parking onahill, first depress thefoot brake
pedal, applytheparking brake,andthen move theshift
lever intotheªPº (Park) position.
R (Reverse) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Use thisposition toback up.Make surethatthevehicle
is completely stoppedbeforeselecting theªRº
(Reverse) position.
N (Neutral) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Neither theforward norreverse gearisengaged. The
engine canbestarted inthis position. You may shift to
the ªNº (Neutral) positionandrestart astalled engine
while thevehicle ismoving.
&RQGLWLRQ


> (GLW   0RGHO &$@
D (Drive) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Use thisposition forallnormal forward driving.
L (Low) (ifequipped) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Use thisposition whenclimbing steephillsslowly or
driving slowlythrough deepsnow,sand ormud, orfor
maximum enginebraking onsteep downhill grades.
Manual shiftmode (ifequipped)
GUID-6A3E4 8D3-F545-46 6F-B2D2-4F57072F6D78
When theshift lever isshifted fromtheªDº position to
the manual shiftgate withthevehicle stopped orwhile
driving, thetransmission entersthemanual shiftmode.
Shift ranges canbeselected manually.
In the manual shiftmode, theshift range isdisplayed
on the position indicator inthe meter.
Shift ranges upordown onebyone asfollows:
M1 ?
/ M2?
/ M3?
/ M4?
/ M5?
/ M6
. When shifting up,move theshift lever tothe +
(up) side. (Shifts tohigher range.)
. When shifting down,movetheshift lever tothe


> (GLW   0RGHO &$@
5-12
Starting anddriving
turn theSPORT modeoff.
Remember nottodrive athigh speeds forextended
periods oftime withtheSPORT modeinthe ªONº
position. Thisreduces fueleconomy .
Accelerator downshift-in the ªDº position -
GUID-FE4ECF FF-36B2-40BE-8768- DFB973246 910
For passing orclimbing hills,depress theaccelerator
pedal tothe floor. Thisshifts thetransmission down
into alower gear,depending onthe vehicle speed.
Shift lockrelease
GUID-7F 9F39D1-C CBB-4C10-9 90D-C12C1B 7B40EB
JVO0027X
Without manualshiftmode (LHDmodel)
If the battery charge islow ordischarged, theshift
lever maynotbemoved fromtheªPº (Park) position
even withthebrake pedal depressed andtheshift lever
button pushed.
T o move theshift lever, perform thefollowing
procedure:
1. Models withIntelligent Keysystem:
Place theignition switchinthe ªOFFº orªLOCKº
position.
Models without Intelligent Keysystem:
Place theignition switchinthe ªLOCKº position,
and remove thekey ifit is inserted. 2.
Apply theparking brake.
3. Push theshift lever button andmove theshift lever
to the ªNº (Neutral) positionwhileholding down
the shift lockrelease.
Place theignition switchinthe ªONº position tounlock
the steering wheel.Thevehicle maybemoved tothe
desired location.
For model withIntelligent Key system: Ifthe battery is
discharged completely,the steering wheelcannot be
unlocked. Donot move thevehicle withthesteering
wheel locked.
If the shift lever cannot bemoved outofthe ªPº (Park)
position, haveaNISSAN dealerchecktheCVT system
as soon aspossible.
WARNING:
If the shift lever cannot bemoved fromtheªPº
(Park) position whiletheengine isrunning and
the brake pedalisdepressed, thestop lights
may notwork. Malfunctioning stoplights could
cause anaccident injuringyourself andothers.
High fluidtemperature protectionmode
GUID-92F6 203D-4431 -412E-BD73-BE0106E 26143
This transmission hasahigh fluidtemperature protec-
tion mode. Ifthe fluid temperature becomestoohigh
(for example, whenclimbing steepgrades inhigh
temperature withheavy loads, suchaswhen towing a
trailer) ,engine powerand,under someconditions,
vehicle speedwillbedecreased automatically to
reduce thechance oftransmission damage.Vehicle
speed canbecontrolled withtheaccelerator pedal,
but engine andvehicle speedmaybelimited.
Fail-safe
GUID-4C5CA0 11-BE46-48EA-A16F-D6 F3A9BF72B8
When thefail-safe operation occurs,theCVT willnot
be shifted tothe selected drivingposition.
If the vehicle isdriven underextreme conditions,
such asexcessive wheelspinning andsubse-
quent hardbraking, thefail-safe systemmaybe
activated. Thiswilloccur evenifall electrical
circuits arefunctioning properly.Inthis case,
place theignition switchinthe ªOFFº position
and wait for10seconds. Thenturntheignition
switch backtothe ªONº position. Thevehicle
should returntoits normal operating condition.
If itdoes notreturn toits normal operating
condition, haveaNISSAN dealercheckthe
transmission andrepair itifnecessary.
WARNING:
When thefail-safe operation occurs,vehicle
speed maybegradually reduced.Thereduced
speed maybelower thanother traffic,which
could increase thechance ofacollision. Be
especially carefulwhendriving. Ifnecessary, pull
to the side ofthe road atasafe place andallow
the transmission toreturn tonormal operation,
or have itrepaired ifnecessary.
&RQGLWLRQ


> (GLW   0RGHO &$@
DRIVING WITHMANUAL TRANSMISSION
(MT)
GUID-08 EE8EF5-22C A-45AE-97E1-FC6FB2E7 A861
WARNING:
. Donot downshift abruptlyonslippery roads.
This maycause aloss ofvehicle control.
. Donot over-rev theengine whenshifting to
a lower gear.Thismay cause aloss of
vehicle control orengine damage.
CAUTION:
. Donot rest your footonthe clutch pedal
while driving. Thismay damage theclutch
system.
. Fully depress theclutch pedalbefore shift-
ing tohelp prevent transmission damage.
. Stop thevehicle completely beforeshifting
into theªRº(Reverse) position.
. When thevehicle isstopped foraperiod of
time, forexample waitingatstoplights, shift
to the ªNº (Neutral) positionandrelease the
clutch pedalwiththefoot brake pedal
depressed.
. Do not shift tothe ªNº (Neutral) position
while driving. Doingsomay result inan
accident duetoloss ofengine braking.
Starting vehicle
GUID-167 57328-65F A-4660-BD9B-5E4335 1F3AF1
1. After starting theengine, depress theclutch pedal
to the floor andmove theshift lever tothe ª1º(1st)
or ªRº (Reverse) position.
2. Slowly depress theaccelerator pedal,releasing
the clutch pedalandparking brakeatthe same
time.
Shifting gear
GUID-70 8BE0C7-A6C5 -48DA-A9C3-3AD53F8A3 232
T o change gears,orwhen upshifting ordownshifting,
fully depress theclutch pedal, shiftintotheappropriate
gear, thenslowly andsmoothly releasetheclutch
pedal.
T o ensure smooth gearchanges, fullydepress the
clutch pedalbefore operating theshift lever. Ifthe
clutch pedalisnot fully depressed beforethe
transmission isshifted, agear noise maybeheard.
T ransmission damagecouldoccur.
Start thevehicle inthe ª1º(1st) position andshift to
the ª2º(2nd) ,ª3º (3rd) ,ª4º (4th) ,ª5º (5th) andª6º
(6th) (ifequipped) gearinsequence according tothe
vehicle speed.
If itis difficult tomove theshift lever intotheªRº
(Reverse) orª1º (1st) position, shifttothe ªNº (Neutral)
position, andthen release theclutch pedalonce.Fully
depress theclutch pedalagainandshift intoªRºorª1º
.
SSD0084
5-speed ManualTransmission (MT)model:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Y ou cannot shiftdirectly fromtheª5º (5th) position into
the R(Reverse) position.FirstshiftintotheN(Neutral)
position, thenshiftintotheR(Reverse)
position.
SSD0552
6-speed ManualTransmission (MT)model:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
. To reverse, stopthevehicle andmove theshift
lever intotheN(Neutral) position,andthen pull
the ring
*
1
upward toshift intotheR(Reverse)
position.
. The ring returns toits original position whenthe
shift lever ismoved tothe N(Neutral) position.
Starting anddriving
5-13
&RQGLWLRQ