warning NISSAN PULSAR 2018 Manual PDF


> (GLW   0RGHO &$@
or acceleration couldcause thewheels toskid and
result inan accident.
W et brakes
GUID-113 04DAE-D8A 1-41C5-9629 -EB4E233FA326
When thevehicle iswashed ordriven through water,
the brakes maygetwet. Asaresult, yourbraking
distance willbelonger andthevehicle maypulltoone
side during braking.
T o dry the brakes, drivethevehicle atasafe speed
while lightly depressing thefoot brake pedal toheat up
the brakes. Dothis until thebrakes returntonormal.
Avoid driving thevehicle athigh speeds untilthe
brakes function correctly.
Parking brakebreak-in
GUID-9F 650418-11 53-4519-A06 7-F7B1AB1F0389
Break inthe parking brakeshoes whenever the
stopping effectofthe parking brakeisweakened or
whenever theparking brakeshoes and/or drums/rotors
are replaced, inorder toassure thebest braking
performance.
This procedure isdescribed inthe vehicle service
manual andcanbeperformed byaNISSAN dealer.
Driving uphill
GUID-98F5 E8C2-2DFE-4 585-B8B6-542F87613 B7A
When starting onasteep grade, itis sometimes
difficult tooperate boththebrake andclutch (for
Manual Transmission model).Apply theparking brake
to hold thevehicle. Donot slip theclutch. Whenready
to start, slowly release theparking brakewhile
depressing theaccelerator pedalandreleasing the
clutch pedal.
Driving downhill
GUID-32139F 93-F218-4D2C-BC4E-B 0CC3241F2E9
The engine braking actioniseffective forcontrolling
the vehicle whiledescending hills.ForManual Trans-
mission (MT)model, theshift lever should beplaced in
the lower speed position priortodescending.For
Continuously Variable Transmission (CVT)model, the
manual shiftmode orthe ªLº position shouldbe
selected.
BRAKE ASSIST (ifequipped)
GUID-CDB FBD03-A9DF-438C-AF 95-F32FB9DAFFB2
When theforce applied tothe brake pedalexceeds a
certain level,theBrake Assist isactivated generating
greater braking forcethanaconventional brake
booster evenwithlight pedal force.
WARNING:
The Brake Assist isonly anaid toassist braking
operation andisnot acollision warningor
avoidance device.Itis the driver's responsibility
to stay alert, drivesafely andbeincontrol ofthe
vehicle atall times.
ANTI-L OCKBRAKING SYSTEM (ABS) (if
equipped)
GUID-C5C2B DDA-1861-49E4-A3EF -B800D31DBF5F
WARNING:
. The Anti-lock BrakingSystem(ABS)isa
sophisticated device,butitcannot prevent
accidents resultingfromcareless ordanger-
ous driving techniques. Itcan help maintain
vehicle control duringbraking onslippery
surfaces. Remember thatstopping distances
on slippery surfaces willbelonger thanon
normal surfaces evenwithABS. Stopping
distances mayalso belonger onrough,
gravel orsnow covered roads,orifyou are using
tirechains. Always maintain asafe
distance fromthevehicle infront ofyou.
Ultimately, thedriver isresponsible for
safety.
. Tire type andcondition mayalso affect
braking effectiveness.
Ð When replacing tires,install thespeci-
fied size oftires onallfour wheels.
Ð When installing aspare tire,make sure
that itis the proper sizeandtype as
specified onthe tire placard. (SeeªTire
placardº (P.9-9) .)
Ð For detailed information, seeªTires and
wheelsº (P.8-31) .
The Anti-lock BrakingSystem(ABS)controls the
brakes sothe wheels donot lock during hardbraking
or when braking onslippery surfaces. Thesystem
detects therotation speedateach wheel andvaries
the brake fluidpressure toprevent eachwheel from
locking andsliding. Bypreventing eachwheel from
locking, thesystem helpsthedriver maintain steering
control andhelps tominimize swerving andspinning
on slippery surfaces.
Using system
GUID-331 31E90-4EC6 -4CBB-B87D-88A622F21705
Depress thebrake pedalandhold itdown. Depress
the brake pedal withfirmsteady pressure, butdonot
pump thebrakes. TheABS willoperate toprevent the
wheels fromlocking up.Steer thevehicle toavoid
obstacles.
WARNING:
Do not pump thebrake pedal. Doingsomay
result inincreased stoppingdistances.
Starting anddriving
5-23
&RQGLWLRQ


> (GLW   0RGHO &$@
5-24
Starting anddriving
Self-test feature
GUID-25A1 2632-42C1- 404E-B198-BDCF201D1 532
The ABS includes electronic sensors,electricpumps,
hydraulic solenoids andacomputer. Thecomputer has
a built-in diagnostic featurethattests thesystem each
time youstart theengine andmove thevehicle atalow
speed inforward orreverse. Whentheself-test
occurs, youmay hear aªclunkº noiseand/or feela
pulsation inthe brake pedal. Thisisnormal anddoes
not indicate amalfunction. Ifthe computer sensesa
malfunction, itswitches theABS offand illuminates the
ABS warning lightonthe instrument panel.Thebrake
system thenoperates normally,but without anti-lock
assistance.
If the ABS warning lightilluminates duringtheself-test
or while driving, havethevehicle checked bya
NISSAN dealer.
Normal operation
GUID-731 7FE84-7D F1-491B-AE 03-A1D3516 5D3DC
The ABS operates atspeeds above5to 10 km/h (3to
6 MPH) .The speed variesaccording toroad condi-
tions.
When theABS senses thatoneormore wheels are
close tolocking up,the actuator rapidlyapplies and
releases hydraulic pressure. Thisaction issimilar to
pumping thebrakes veryquickly .You may feela
pulsation inthe brake pedalandhear anoise from
under thehood orfeel avibration fromtheactuator
when itis operating. Thisisnormal andindicates that
the ABS isoperating properly.However, thepulsation
may indicate thatroad conditions arehazardous and
extra careisrequired whiledriving.
GUID-161 29265-62AC- 4A0C-9B39-4 8A5D69BB276
When leaving yourvehicle unoccupied:
. Always takethekey with you-even when leaving
the vehicle inyour owngarage.
. Close allwindows completely andlock alldoors.
. Always parkyourvehicle whereitcan beseen.
Park inawell litarea during thenight.
. Ifthe security systemisequipped, useit-even for
a short period.
. Never leavechildren orpets inthe vehicle
unattended.
. Never leavevaluables insidethevehicle. Always
take valuables withyou.
. Never leavethevehicle documents inthe vehicle.
. Never leavearticles onaroof rack. Remove them
from therack andkeep andlock them inside the
vehicle.
. Never leavethespare keyinthe vehicle.
GUID-EBC9 7F4F-D1CC-40F0-8EC6-B8EC419B4 084
WARNING:
. Whatever thecondition, drivewithcaution.
Accelerate anddecelerate withgreat care.If
accelerating ordecelerating toofast, the
drive wheels willlose even more traction.
. Allow morestopping distanceincold weath-
er driving. Braking shouldbestarted sooner
than ondry pavement.
. Keep atagreater distance fromthevehicle
in front ofyou onslippery roads.
. Wet ice(08C ,328F andfreezing rain),very
cold snow andicecan beslick andvery
difficult todrive on.The vehicle willhave a
lot less traction orgrip under thesecondi-
tions. Try to avoid driving onwet iceuntil the
road issalted orsanded.
. Watch forslippery spots(glaring ice).These
may appear onanotherwise clearroadin
shaded areas.Ifapatch ofice isseen ahead,
brake before reaching it.Try not tobrake
while actually onthe ice, and avoid any
sudden steering maneuvers.
. Donot use cruise control onslippery roads.
. Snow cantrap dangerous exhaustgasunder
your vehicle. Keepsnow clearofthe exhaust
pipe andfrom around yourvehicle.
VEHICLE SECURITY COLDWEATHER DRIVING
&RQGLWLRQ


> (GLW   0RGHO &$@
6-2
In case ofemergency
GUID-DC13 C8BB-D3C5 -4ABE-9B25 -588DE68D 652F
SIC2475
The hazard indicator flasherswitchoperates regard-
less ofthe ignition switchposition exceptwhenthe
battery isdischarged.
The hazard indicator flasherisused towarn other
drivers whenyouhave tostop orpark under
emergency conditions.
When thehazard indicator flasherswitchispushed, all
turn signal lightswillflash. To turn offthe hazard
indicator flasher,pushthehazard indicator flasher
switch again.
GUID-731 D6607-4AF E-4B6B-8CEA- 9FC3B0AD95C8
If you have aflat tire, follow theinstructions asfollows.
ST OPPING VEHICLE
GUID-6E33 62D8-C092 -442C-91E5- C16CBD838BC7
WARNING:
. Besure toapply theparking brakefirmly.
. Besure tomove theshift lever tothe ªRº
(Reverse) position(ManualTransmission
(MT) model) .
. Besure tomove theshift lever tothe ªPº
(Park) position (Continuously Variable
T ransmission (CVT)model) .
. Never change tireswhen thevehicle ison a
slope, iceorslippery area.Thisishazardous.
. Never change tireswhen theoncoming
traffic isclose toyour vehicle. Callfor
professional roadassistance.
1. Safely movethevehicle offthe road away from
traffic.
2. Turn onthe hazard indicator flasherlights.
3. Park onalevel surface.
4. Apply theparking brake.
5. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªRº (Reverse) position.
6. Turn offthe engine.
7. Open thehood:
.
T o warn other traffic.
.
T o signal professional roadassistance person-
nel that youneed assistance.
8. Have allpassengers getoutfrom thevehicle and
stand inasafe place, awayfromother traffic and clear
ofthe vehicle.
PREP ARING TOOLS ANDSPARE TIRE
GUID-0A9AE2 68-59C1-4A9D-8532-F659 3649CFF6
JVE0104X
Open theback door. Raise thecargo floorboard
*
1
.
Remove jackingtools.
HAZARD INDICATOR FLASHER
SWIT CH FLA
TTIRE
&RQGLWLRQ


> (GLW   0RGHO &$@
JVE0019X
The spare tireislocated underthecargo floorboard.
Loosen theclamp
*
2
and remove thespacer
*
1
and
take outthespare tire.
BL OCKING WHEELS
GUID-23 E7DEFB-5802 -48C9-BB6F-FDF013EA 5A18
MCE0001D
WARNING:
Be sure toblock theappropriate wheelto
prevent thevehicle frommoving, whichmay
cause personal injury.
Place suitable blocks
*
1
at both thefront andback of
the wheel diagonally oppositetheflattire
*
A
to
prevent thevehicle frommoving whenitis jacked up.
REMOVING WHEELCOVER (ifequipped)
GUID-03E2 B6E6-23A9-4 BB1-9E8F-DBC8ACF2A 577
SCE0630
WARNING:
Never useyour hands toremove thewheel
cover. Thismaycause personal injury.
T o remove thewheel cover, usethejack rod
*
1
as
illustrated.
Apply cloth
*
2
between thewheel andjack rodto
prevent damaging thewheel andwheel cover.
REMOVING TIRE
GUID-F9E36 B2A-7AA5-4 B04-8663-E2B23C1A97 CC
Jacking upvehicle
GUID-B3 7ACDE4-B 409-461F-93 E1-BF96415D 844D
JVE0016X
Jack -uppoints
In case ofemergency
6-3
&RQGLWLRQ


> (GLW   0RGHO &$@
6-4
In case ofemergency
SCE0504
WARNING:
. Besure toread andfollow theinstructions in
this section.
. DO NOTGET UNDER AVEHICLE THATIS
SUPPORTED BY A JACK .
. Never useajack which isnot provided with
your vehicle.
. The jack, which isprovided withyour vehicle,
is designed onlytolift your vehicle duringa
tire change. Donot use thejack provided
with your vehicle onother vehicles.
. Never jackupthe vehicle atalocation other
than thejack -uppoint thatisspecified.
. Never liftthe vehicle morethannecessary.
. Never useblocks onorunder thejack.
. Never startorrun theengine whilethe
vehicle ison the jack. Thevehicle maymove
suddenly, andthismay cause anaccident.
. Never allowpassengers toremain inthe
vehicle whilethetire isoff the ground. .
Besure toread thecaution labelattached to
the jack body before using.
1. Place thejack directly underthejack-up point as
illustrated sothat thetop ofthe jack contacts the
vehicle atthe jack-up point.
The jack should beplaced onfirm level
ground.
2. Align thejack head between thetwo notches
located atthe jack-up point ofeither thefront or
the rear section.
3. Fitthe groove ofthe jack head between the
notches asshown.
4. Loosen eachwheel nut,counterclockwise, oneor
two turns withthewheel nutwrench.
Do not remove thewheel nutsuntil thetire is
off the ground.
5. Carefully raisethevehicle untiltheclearance
between thetireand ground isachieved.
6. To lift the vehicle, securely holdthejack lever and
rod with both hands andturn thejack lever.
Removing tire
GUID-972 115C8-16B 3-429F-9DF 1-CC69110A0 0AF
1. Remove thewheel nuts.
2. Remove thedamaged tire.
CAUTION:
The tireisheavy. Besure thatyour feetareclear
from thetire and usegloves asnecessary to
avoid injury.
INST ALLING SPARE TIRE
GUID-028 A15EE-D4 CA-4435-AF C6-94D3C9E C3071
SCE0039
WARNING:
. Never usewheel nutswhich arenot provided
with your vehicle. Incorrect wheelnutsor
improperly tightenedwheelnutsmaycause
the wheel tobecome looseorcome off.This
could cause anaccident.
. Never useoilorgrease onthe wheel studs
or nuts. Thismaycause thewheel nutsto
become loose.
1. Clean anymud ordirt from thesurface between
the wheel andhub.
&RQGLWLRQ


> (GLW   0RGHO &$@
2. Carefully putthespare tireonand tighten the
wheel nutswithyour fingers. Checkthatallthe
wheel nutscontact thewheel surface horizontally .
3. Tighten thewheel nutsalternately andevenly in
the sequence illustrated(
*
1
-
*
5
) , more than2
times withthewheel nutwrench, untilthey are
tight.
4. Lower thevehicle slowlyuntilthetire touches the
ground.
5. Tighten thewheel nutssecurely ,with thewheel
nut wrench, inthe sequence illustrated.
6. Lower thevehicle completely .
Tighten thewheel nutstothe specified torque
with atorque wrench assoon aspossible.
Wheel nuttightening torque:
108 N´m (11kg-m, 80ft-lb)
The wheel nutsmust bekept tightened to
specification atall times. Itis recommended
that thewheel nutsbetightened tospecification
at each lubrication interval.
WARNING:
Retighten thewheel nutswhen thevehicle has
been driven for1,000 km(600 miles) (alsoin
cases ofaflat tire, etc.).
ST OWING DAMAGED TIREANDTOOLS
GUID-1FAB B527-F376-4605-B0E 8-545A3C1B479F
WARNING:
Be sure thatthetire, jack andtools usedare
properly storedafteruse.Such items can
become dangerous projectilesinan accident or
sudden stop.
1. Securely storethejack, tools andthedamaged
tire inthe storage area.
2. Replace thecargo floorboard.
3. Close theback door.
GUID-CA 3FC571-40 A7-4E0F-A6D6-412F4AB 6C190
WARNING:
. Incorrect jumpstarting canlead toabattery
explosion. Thebattery explosion mayresult
in severe injuryordeath. Itmay also result in
damage tothe vehicle. Besure tofollow the
instructions inthis section.
. Explosive hydrogengasisalways present in
the vicinity ofthe battery. Keepallsparks
and flames awayfromthebattery.
. Always wearsuitable eyeprotection and
remove rings,bracelets, andanyother jew-
elry whenever workingonornear abattery.
. Never leanover thebattery whilejump
starting.
. Never allowbattery fluidtocome into
contact witheyes, skin,clothes orthe
vehicle's paintedsurfaces. Batteryfluidisa
corrosive sulfuricacidwhich cancause
severe burns.Ifthe fluid comes intocontact
with anything, immediately flushthecon-
tacted areawithplenty ofwater.
. Keep thebattery outofthe reach ofchildren.
. The booster batterymustberated at12
volts. Useofan incorrectly ratedbattery will
damage yourvehicle.
. Never attempt tojump startafrozen battery.
It could explode andcause serious injury.
In case ofemergency
6-5
JUMP
STARTING
&RQGLWLRQ


> (GLW   0RGHO &$@
GUID-9D9 20AF3-899 E-4949-B9DE-B9DA38E BCD0D
Do not attempt tostart theengine bypushing the
vehicle.
CAUTION:
. Continuously Variable Transmission (CVT)/
Manual Transmission (MT)model cannot be
started bypushing. Attempting todo somay
cause damage tothe transmission.
. Three-way catalystequipped modelshould
not bestarted bypushing. Attempting todo
so may cause damage tothe catalyst.
. Never trytostart theengine bytowing.
When theengine starts,theforward surge
could cause thevehicle tocollide withthe
towing vehicle.
GUID-6FF3 F0CC-8B6E -46AC-926D-3 EB9C863FE4D
WARNING:
. Never continue drivingifyour vehicle over-
heats. Doingsocould cause avehicle fire.
. Never openthehood ifsteam iscoming out.
. Never remove theradiator orcoolant reser-
voir capwhile theengine ishot. Ifthe
radiator orcoolant reservoir capisremoved
when theengine ishot, pressurized hot
water willspurt outand possibly cause
burning, scalding orserious injury.
. Ifsteam orcoolant iscoming fromthe
engine, standclearofthe vehicle toprevent
getting burned.
. The engine cooling fanwill start atanytime
when thecoolant temperature exceedspre-
set degrees.
. Becareful nottoallow yourhands, hair,
jewelry orclothing tocome intocontact with,
or toget caught inthe cooling fanordrive
belts.
If your vehicle isoverheating (indicatedbythe high
temperature indicator),or ifyou feel alack ofengine
power, detectunusual noise,etc.,takethefollowing
steps:
1. Safely movethevehicle offthe road away from
traffic.
2. Turn onthe hazard indicator flasherlights.
3. Apply theparking brake.
4. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªNº (Neutral) position.
DO NOTST OP THE ENGINE . 5.
Open allthe windows.
6. Turn offthe airconditioner. Movethetemperature
control tomaximum hotand thefancontrol tohigh
speed.
7. Get outfrom thevehicle.
8. Visually inspectandlisten forsteam orcoolant
escaping fromtheradiator beforeopening the
hood. Wait until nosteam orcoolant canbeseen
before proceeding.
9. Open theengine hood.
10. Visually inspectifthe cooling fanisrunning.
11. Visually inspecttheradiator andradiator hosesfor
leakage.
If the cooling fanisnot running orthe coolant is
leaking, stoptheengine.
12. After theengine coolsdown, checkthecoolant
level inthe reservoir withtheengine running. Do
not open theradiator cap.
13. Add coolant tothe reservoir ifnecessary .
Have yourvehicle inspected/repaired ataNISSAN
dealer.
In case ofemergency
6-7
PUSH
STARTING IFYOUR VEHICLE OVERHEA TS
&RQGLWLRQ


> (GLW   0RGHO &$@
Freeing trapped vehicle
GUID-E1C5 3A8A-382D-4409-936A -B6A11CAB 094F
WARNING:
. Never allowanyone tostand nearthetowing
line during thepulling operation.
. Never spinthetires athigh speed. Thiscould
cause themtoexplode andresult inserious
injury. Partsofthe vehicle couldalsoover-
heat andbedamaged.
. Donot pull thevehicle usingtherear hook.
The rear hook isnot designed topull the
vehicle outinthe event thatthevehicle
becomes trapped.
In the event thatyour vehicle's tiresbecome trappedin
sand, snow,or mud, andthevehicle isunable tofree
itself without beingpulled, usetherecovery hooks.
. Use therecovery hooksonly.Do not attach the
pulling devicetoany other partofthe vehicle body.
Otherwise, thevehicle bodymaybedamaged.
. Use therecovery hookstofree avehicle only.
. The recovery hooksareunder tremendous stress
when usedtofree atrapped vehicle.Alwayspull
the pulling devicestraight outfrom thevehicle.
Never pullonthe recovery hooksatan angle. Front
:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
JVE0017X
Front
SCE0833
Front
*
1
Remove thehook cover fromthebumper witha
suitable tool.
*
2
Securely installtherecovery hookasillustrated.
(The hook isstored withthejacking tools.)
Make surethattherecovery hookisproperly secured
in its storage areaafter use. Rear:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
SCE0944
Rear
Do not use therear hook topull thevehicle.
In case ofemergency
6-9
&RQGLWLRQ


> (GLW   0RGHO &$@
7-4
Appear anceandcare
AIR FRESHENERS
GUID-491C 1655-FB80-4 2E5-B748-615749AEB 247
Most airfresheners useasolvent thatcould affect the
vehicle interior. Ifyou use anairfreshener, takethe
following precautions:
. Hanging-type airfresheners cancause permanent
discoloration whentheycontact vehicleinterior
surfaces. Placetheairfreshener inalocation that
allows itto hang freeandnotcontact aninterior
surface.
. Liquid-type airfresheners typicallycliponthe
vents. These products cancause immediate
damage anddiscoloration whenspilled oninterior
surfaces.
Carefully readandfollow themanufacturer's instruc-
tions before usingairfresheners.
FL OOR MATS
GUID-FE B53C0F-2B1 3-4DA5-9FFC -A4B230889197
The useofgenuine NISSAN floormats (ifequipped)
can extend thelifeofyour vehicle carpetandmake it
easier toclean theinterior. Regardless ofwhat mats
are used, besure theyarefitted foryour vehicle and
are properly positioned inthe foot well toprevent
interference withpedal operation. Matsshould be
maintained withregular cleaning andreplaced ifthey
become excessively worn.
Floor matpositioning aid(driver's side)
GUID-0F 3306F1-4A E6-4165-B1 83-646B6 719990D
JV A0010X
Example (LHDmodel)
This vehicle includes frontfloormatbrackets toact as
a floor matpositioning aid.NISSAN floormats have
been specially designed foryour vehicle model.
P osition themat byplacing thefloor matbracket hook
through thefloor matgrommet holewhile centering the
mat inthe foot area.
Periodically checkthatthemats areproperly posi-
tioned.
GLASS
GUID-47B68 639-6537-4853-8BB4-A5E527CF1 D3C
Use glass cleaner toremove smokeanddust filmfrom
the glass surfaces. Itis normal forglass tobecome
coated withafilm after thevehicle isparked inthe hot
sun. Glass cleaner andasoft cloth willeasily remove
this film.
CAUTION:
When cleaning theinside ofthe windows, donot
use sharp-edged tools,abrasive cleanersor
chlorine-based disinfectantcleaners.Theycould
damage theelectrical conductors, suchasrear
window defogger elements.
SEA TBEL TS
GUID-30 F2EF69-84CD -4146-8EDF-44903B81 C08C
WARNING:
. Donot allow wetseat belts toroll upinthe
retractor.
. Never usebleach, dyeorchemical solvents
to clean theseat belts, sincethese materials
may severely weakentheseat beltwebbing.
The seat belts canbecleaned bywiping themwitha
sponge dampened inamild soap solution.
Allow thebelts todry completely inthe shade before
using them. (SeeªSeat beltsº (P.1-7) .)
&RQGLWLRQ


> (GLW   0RGHO &$@
Tires*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepressure withagauge oftenandalways
prior tolong distance trips.Adjust thepressure inall
tires, including thespare, tothe pressure specified.
Check carefully fordamage, cutsorexcessive wear.
Tire rotation*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
In the case thatTwo-Wheel Drive(2WD) andfront &
rear tires aresame size;Tires should berotated every
10,000 km(6,000 miles).Tires marked withdirectional
indicators canonly berotated between frontandrear.
Make surethatthedirectional indicatorspointinthe
direction ofwheel rotation afterthetire rotation is
completed.
In the case thatFour-Wheel Drive(4WD) andfront &
rear tires aresame size;Tires should berotated every
5,000 km(3,000 miles).Tires marked withdirectional
indicators canonly berotated between frontandrear.
Make surethatthedirectional indicatorspointinthe
direction ofwheel rotation afterthetire rotation is
completed.
In the case thatfront tiresaredifferent sizefrom rear
tires; Tirescannot berotated.
However, thetiming fortire rotation mayvaryaccording
to your driving habitsandtheroad surface conditions.
Tire Pressure Monitoring System(TPMS)trans-
mitter components (ifequipped) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Replace theTPMS transmitter grommetseal,valve
core andcap when thetires arereplaced duetowear
or age.
Wheel alignment andbalance:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
If the vehicle shouldpulltoeither sidewhile driving on
a straight andlevel road, orifyou detect uneven or
abnormal tirewear, theremaybeaneed forwheel
alignment. Ifthe steering wheelorseat vibrates at
normal highway speeds,wheelbalancing maybe needed.
Windshield:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Clean thewindshield onaregular basis.Check the
windshield atleast every sixmonths forcracks orother
damage. Repairasnecessary .
Wiper blades*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check forcracks orwear ifnot functioning correctly.
Inside vehicle
GUID-55 4469D2-12 96-4F49-B7A0 -0A8847FB7455
The maintenance itemslistedhereshould bechecked
on aregular basis,suchaswhen performing periodic
maintenance, cleaningthevehicle, etc.
Accelerator pedal:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepedal forsmooth operation andmake sure
that thepedal doesnotcatch orrequire uneven effort.
K eep thefloor mats away fromthepedal.
Brake pedal*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepedal forsmooth operation andmake sure
that itis the proper distance fromthefloor matwhen
depressed fully.Check thebrake booster function. Be
sure tokeep thefloor mats away fromthepedal.
Parking brake*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check theparking brakeoperation regularly.Check
that thelever (ifequipped) orthe pedal (ifequipped)
has theproper travel.Alsomake surethatthevehicle is
held securely onafairly steep hillwhen onlythe
parking brakeisapplied.
Seat belts:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatallparts ofthe seat beltsystem (for
example, buckles,anchors, adjusters andretractors)
operate properly andsmoothly ,and areinstalled
securely .Check thebelt webbing forcuts, fraying,
wear ordamage. Steering
wheel:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check forchanges inthe steering condition, suchas
excessive play,hard steering orstrange noises.
Warning lightsandchimes:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Make surethatallwarning lightsandchimes are
operating properly.
Windshield defogger:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thattheaircomes outofthe defogger outlets
properly andingood quantity whenoperating the
heater orair conditioner.
Windshield wiperandwasher*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatthewipers andwasher operate properly
and that thewipers donot streak.
Under hoodandvehicle
GUID-E5D 10961-EA14 -4A37-B87E- 268783A0FC3 8
The maintenance itemslistedhereshould bechecked
periodically (forexample, eachtimeyoucheck the
engine oilorrefuel) .
Battery*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Except formaintenance freebattery ,check thefluid
level ineach cell.Itshould bebetween theªUPPERº
and ªLOWERº lines.Vehicles operated inhigh
temperatures orunder severe conditions require
frequent checksofthe battery fluidlevel.
Brake (andclutch) fluidlevel(s)*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
For Manual Transmission (MT)model; makesurethat
the brake andclutch fluidlevels arebetween the
ªMAXº andªMINº linesonthe reservoirs.
Except forManual Transmission (MT)model; make
sure thatthebrake fluidlevel isbetween theªMAXº
and ªMINº linesonthe reservoir.
Maintenan ceand do-it-you rself
8-3
&RQGLWLRQ