can NISSAN TEANA 2003 Service Manual

LAN-44
[CAN]
TROUBLE DIAGNOSIS

TROUBLE DIAGNOSISPFP:00004
CAN Diagnostic Support MonitorBKS002DN
Use “CAN DIAG SUPPORT MNTR” for detecting the root cause.
MONITOR ITEM LIST (CONSULT-II)
ECM
NOTE:
Replace the unit when “NG” is indicated on the “INITIAL DIAG”.
Driver seat control unit
NOTE:
Replace the unit when “NG” is indicated on the “INITIAL DIAG”.
AFS control unit
0: Error at present, 1 – 39: Error in the past (Number means the number of times the ignition switch is turned OFF→ON)
*: 39 or higher number is fixed at 39 until the self-diagnosis result is erased.SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT
ENGINEINITIAL DIAG Status of CAN controller
OKNG
TRANSMIT DIAG Signal transmission status
UNKWN TCM Signal receiving status from the TCM
VDC/TCS/ABSModels with VDC: Signal receiving status from the ABS actuator
and electric unit (control unit)
Models with ABS: Not used even though indicated
METER/M&A Signal receiving status from the unified meter and A/C amp. OK UNKWN
ICC Not used even though indicated
BCM/SEC Signal receiving status from the BCM
OK UNKWN
IPDM E/R Signal receiving from the IPDM E/R
AWD/4WD/e4WD
Not used even though indicated
EPS
SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT
AUTO DRIVE
POS.INITIAL DIAG Status of CAN controller
OKNG
TRANSMIT DIAG Signal transmission status
UNKWN BCM/SEC Signal receiving status from the BCM
METER/M&A Signal receiving status from the unified meter and A/C amp.
TCM Signal receiving status from the TCM
SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT PAST PRSNT PAST
ADAPTIVE
LIGHTTRANSMIT DIAG Not used even though indicated
ECM Signal receiving status from the ECM
OKOK
or
1 – 39
*UNKWN 0 METER/M&ASignal receiving status from the unified
meter and A/C amp.
TCM Signal receiving status from the TCM
STRGSignal receiving status from the steering
angle sensor
EPS Not used even though indicated
IPDM E/R Signal receiving status from the IPDM E/R OKOK
or
1 – 39
*UNKWN 0

TROUBLE DIAGNOSIS
LAN-45
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN

BCM
NOTE:
Replace the unit when “NG” is indicated on the “INITIAL DIAG”.
Intelligent Key unit
0: Error at present, 1 – 39: Error in the past (Number means the number of times the ignition switch is turned OFF→ON)
*: 39 or higher number is fixed at 39 until the self-diagnosis result is erased.
Unified meter and A/C amp.
0: Error at present, 1 – 39: Error in the past (Number means the number of times the ignition switch is turned OFF→ON)
*: 39 or higher number is fixed at 39 until the self-diagnosis result is erased.SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT
BCMINITIAL DIAG Status of CAN controller
OKNG
TRANSMIT DIAG Signal transmission status
UNKWN ECM Signal receiving status from the ECM
IPDM E/R Signal receiving from the IPDM E/R
METER/M&A Signal receiving status from the unified meter and A/C amp.
I-KEY Not used even though indicated
TCM Signal receiving status from the TCM OK UNKWN
SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT PAST PRSNT PAST
INTELLIGENT
KEYTRANSMIT DIAG Signal transmission status
OKOK
or
1 – 39
*UNKWN 0 ECM Signal receiving status from the ECM
METER/M&ASignal receiving status from the unified
meter and A/C amp.
BCM/SEC Signal receiving status from the BCM
SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT PAST PRSNT PAST
METER A/C AMPTRANSMIT DIAG Signal transmission status
OKOK
or
1 – 39
*UNKWN 0 ECM Signal receiving status from the ECM
TCM Signal receiving status from the TCM
BCM/SEC Signal receiving status from the BCM
VDC/TCS/ABSSignal receiving status from the ABS actu-
ator and electric unit (control unit)
IPDM E/R Not used even though indicated
DISPLAYModels with color display: Signal receiving
status from the display control unit
OKOK
or
1 – 39
*UNKWN 0 Models without color display: Signal
receiving status from the display unit
I-KEYSignal receiving status from the Intelligent
Key unit
EPS
Not used even though indicated AW D/4W D
e4WD
ICC
LANE KEEP
TIRE-P

LAN-46
[CAN]
TROUBLE DIAGNOSIS

TCM (Models with A/T)
NOTE:
Replace the unit when “NG” is indicated on the “INITIAL DIAG”.
TCM (Models with CVT)
NOTE:
Replace the unit when “NG” is indicated on the “INITIAL DIAG”.
ABS actuator and electric unit (control unit) (Models with ABS)
0: Error at present, 1 – 39: Error in the past (Number means the number of times the ignition switch is turned OFF→ON)
*: 39 or higher number is fixed at 39 until the self-diagnosis result is erased.
ABS actuator and electric unit (control unit) (Models with VDC)
CAUTION:
Never replace the unit even when “NG” is indicated on the “INITIAL DIAG” at this stage. Follow the trouble diagnosis proce-
dures. SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT
A/TINITIAL DIAG Status of CAN controller
OKNG
TRANSMIT DIAG Signal transmission status
UNKWN ECM Signal receiving status from the ECM
VDC/TCS/ABSModels with VDC: Signal receiving status from the ABS actuator
and electric unit (control unit)
Models with ABS: Not used even though indicated
METER/M&ASignal receiving status from the unified meter and A/C amp.
meterOK UNKWN
ICC/e4WD Not used even though indicated
SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT
TRANSMISSIONINITIAL DIAG Status of CAN controller
OKNG
TRANSMIT DIAG Signal transmission status
UNKWN ECM Signal receiving status from the ECM
VDC/TCS/ABSSignal receiving status from the ABS actuator and electric unit
(control unit)
METER/M&A Signal receiving status from the unified meter and A/C amp.
ICC Not used even though indicated
SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT PAST PRSNT PAST
ABSTRANSMIT DIAG Signal transmission status
OKOK
or
1 – 39*UNKWN 0
ECM Signal receiving status from the ECM
SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT
ABSINITIAL DIAG Status of CAN controller
OKNG
Caution
TRANSMIT DIAG Signal transmission status
UNKWN ECM Signal receiving status from the ECM
TCM Signal receiving status from the TCM
METER/M&A Not used even though indicated
STRG Signal receiving status from the steering angle sensor OK UNKWN
ICC Not used even though indicated

TROUBLE DIAGNOSIS
LAN-47
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN

IPDM E/R
0: Error at present, 1 – 39: Error in the past (Number means the number of times the ignition switch is turned OFF→ON)
*: 39 or higher number is fixed at 39 until the self-diagnosis result is erased.SELECT SYS-
TEMCAN DIAG SUP-
PORT MNTRDescriptionNormal Error
PRSNT PAST PRSNT PAST
IPDM E/RTRANSMIT DIAG Signal transmission status
OKOK
or
1 – 39*UNKWN 0 ECM Signal receiving status from the ECM
BCM/SEC Signal receiving status from the BCM

LAN-48
[CAN]
TROUBLE DIAGNOSIS

MONITOR ITEM LIST (ON-BOARD DIAGNOSIS)
Display control unit
NOTE:
CAN diagnostic support monitor of the display control unit is indicated on the vehicle display.

Models with color display: Refer to AV- 9 3 , "CAN DIAGNOSIS" .
*: The error counter stops counting when it reaches “50” and holds “50” until it is reset.
PKIC9893E
Unit name Diagnosis item DescriptionIndicated items on CAN DIAG SUPPORT MONITOR
Normal Error
Result indi-
catedError
counter
(Reference)Result indi-
catedError
counter
(Reference)
Display control
unitCommunication Status of CAN controller
OK0
or
1 – 50*NG
1 – 50* CAN System 1 Signal transmission status
UNKWN CAN System 2Signal receiving status from the
BCM
CAN System 3Signal receiving status from the
ECM
CAN System 4 Not used even though indicated
CAN System 5Signal receiving status from the
unified meter and A/C amp.OK0
or
1 – 50*UNKWN 1 – 50*
CAN System 6 Not used even though indicated
CAN System 7Signal receiving status from the
IPDM E/ROK0
or
1 – 50*UNKWN 1 – 50*
CAN System 8
Not used even though indicated
CAN System 9

TROUBLE DIAGNOSIS
LAN-49
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN

CAN System Specification ChartBKS002DO
Determine CAN system type from the following specification chart. Then choose the correct diagnosis sheet.
NOTE:
Refer to LAN-19, "
CHECK OF CAN SYSTEM TYPE (HOW TO USE CAN SYSTEM TYPE SPECIFICATION
CHART)" for how to use CAN system specification chart.
×: ApplicableBody typeSedan
Axle2WD
Engine QR20DE/VQ23DE VQ23DE VQ35DE
Transmission A/T CVT
Brake control ABS VDC
Automatic drive positioner×××
Adaptive front-lighting system××
Intelligent Key system××
Integrated display system××
Integrated color display system××
CAN system type 1 2 3 4
Diagnosis sheetLAN-64, "
DIAG-
NOSIS SHEET"
LAN-65, "DIAG-
NOSIS SHEET"
LAN-66, "DIAG-
NOSIS SHEET"
LAN-67, "DIAG-
NOSIS SHEET"
CAN communication signal chartLAN-51, "TYPE 1/TYPE 2"LAN-52, "TYPE 3"LAN-54, "TYPE 4"

LAN-50
[CAN]
TROUBLE DIAGNOSIS

VEHICLE EQUIPMENT IDENTIFICATION INFORMATION
NOTE:
Check CAN system type from the vehicle shape and equipment.
PKIC9870E

TROUBLE DIAGNOSIS
LAN-51
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN

CAN Communication Signal ChartBKS002DP
Refer to LAN-15, "How to Use CAN Communication Signal Chart" for how to use CAN communication signal
chart.
TYPE 1/TYPE 2
NOTE:
Refer to LAN-41, "
Abbreviation List" for the abbreviations of the connecting units.
T: Transmit R: Receive
Signals
ECM
ADP
BCM
M&A
DISP
TCM
ABS
IPDM-E
A/C compressor request signal T R
Accelerator pedal position signal T R
Closed throttle position signal T R
Cooling fan speed request signal T R
Engine and A/T integrated control signalTR
RT
Engine coolant temperature signal T R
Engine speed signal T R
Fuel consumption monitor signalTR
TR
Malfunction indicator signal T R
Wide open throttle position signal T R
A/C switch signal R T
Blower fan motor switch signal R T
Buzzer output signal T R
Door switch signal R T R R
Front fog light request signal T R R
Front wiper request signal T R
High beam request signal T R R
Ignition switch signal R T R
Key fob door unlock signal R T
Key fob ID signal R T
Key switch signal R T
Low beam request signal T R
Oil pressure switch signalRT
TR
Position light request signal T R R
Rear fog status signal T R
Rear window defogger switch signal T R
Sleep wake up signal T R R
Turn indicator signal T R
3rd position switch signal T R
A/C switch/indicator signalRT
TR
Distance to empty signal T R
Fuel level low warning signal T R
Stop lamp switch signal T R

LAN-52
[CAN]
TROUBLE DIAGNOSIS

*: P range only
TYPE 3
NOTE:
Refer to LAN-41, "
Abbreviation List" for the abbreviations of the connecting units.
T: Transmit R: Receive Vehicle speed signalRT
RRR T R
A/T CHECK indicator lamp signal R T
A/T position indicator lamp signal
R
*RT
Output shaft revolution signal R T
ABS warning lamp signal R T
Brake warning lamp signal R T
Front wiper stop position signal R T
High beam status signal R T
Low beam status signal R T
Rear window defogger control signal R R R TSignals
ECM
ADP
BCM
M&A
DISP
TCM
ABS
IPDM-E
SignalsECM
ADP
AFS
BCM
I-KEY
M&A
STRG
DISP
TCM
ABS
IPDM-E
A/C compressor request signal TR
Accelerator pedal position signal T R R
Closed throttle position signal T R
Cooling fan speed request signal TR
Engine and A/T integrated control signalTR
RT
Engine coolant temperature signal T R
Engine speed signal T R R
Fuel consumption monitor signalTR
TR
Malfunction indicator signal T R
Wide open throttle position signal T R
A/C switch signal R T
Blower fan motor switch signal R T
Buzzer output signalTR
TR
Door lock/unlock status signal T R
Door switch signal R T R R R
Front fog light request signal T R R
Front wiper request signal T R
High beam request signal T R R
Ignition switch signal R T R
Key fob door unlock signal R T
Key fob ID signal R T
Key switch signal R T

TROUBLE DIAGNOSIS
LAN-53
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN

*: P range onlyLow beam request signal T R
Oil pressure switch signalRT
TR
Position light request signal T R R
Rear fog status signal T R
Rear window defogger switch signal T R
Sleep wake up signalTRR R
RT
Turn indicator signal T R
Door lock/unlock/trunk open request signal R T
Hazard warning lamp request signal R T
Ignition knob switch signal R T
Key warning signal T R
Starter permission signal R T
3rd position switch signal T R
A/C switch/indicator signalRT
TR
Distance to empty signal T R
Fuel level low warning signal T R
Stop lamp switch signal T R
Vehicle speed signalRT
RRRRR T R
Steering angle sensor signal R T R
A/T CHECK indicator lamp signal R T
A/T position indicator lamp signal
R
*RR T
Output shaft revolution signal R T
ABS warning lamp signal R T
Brake warning lamp signal R T
SLIP indicator lamp signal R T
VDC OFF indicator lamp signal R T
VDC operation signalRT
Front wiper stop position signal R T
High beam status signal R R T
Low beam status signal R R T
Rear window defogger control signal R R R TSignals
ECM
ADP
AFS
BCM
I-KEY
M&A
STRG
DISP
TCM
ABS
IPDM-E