NISSAN TEANA 2003 Service Manual

FRONT DOOR LOCK
BL-123
C
D
E
F
G
H
J
K
L
MA
B
BL

FRONT DOOR LOCKPFP:80502
Component StructureBIS000XV
Removal and Installation BIS000XW
REMOVAL
1. Remove the front door finisher. Refer to EI-35, "DOOR FINISHER" .
2. Disconnect inside handle cable and lock knob cable from inside handle.
CAUTION:
During removal and installation, work so as not to bend the
ends of the lock knob cable and inside handle cable.
1. Outside handle 2. Front gasket 3. TORX bolt (T30)
4. Lock knob cable 5. Inside handle 6. Screw
7. Inside handle cable 8. Door lock assembly 9. Outside handle cable
10. Clip 11. Key cylinder connecting rod (Driver
side only)12. TORX bolt (T30)
13. Outside handle bracket 14. TORX bolt (T30) 15. Grommet
16. Rear gasket 17. Door key cylinder assembly (Driver
side)
PIIB0282E
PIIA0632E

BL-124
FRONT DOOR LOCK

3. Remove the front door glass and front door module assembly. Refer to GW-46, "FRONT DOOR GLASS
AND REGULATOR" .
4. Remove key cylinder connecting rod (key cylinder side). (Driver side only)
5. Disconnect door antenna and door request switch connector
and remove harness clamp. (Models with intelligent key systems
only)
6. Remove door side grommet, and remove door key cylinder assembly (driver side) and outside handle
escutcheon (passenger side) bolts (TORX T30) from grommet hole.
CAUTION:
Do not forcibly remove the TORX bolts (T30).
7. Reach to separate the key cylinder rod connection (on the handle).
8. While pulling the outside handle, remove door key cylinder
assembly (driver side) and outside handle escutcheon (passen-
ger side).
9. While pulling outside handle, slide toward rear of vehicle to
remove outside handle.
10. Remove the front gasket and rear gasket.
PIIB0283E
MIIB0128E
MIIB0129E
MIIB0130E

FRONT DOOR LOCK
BL-125
C
D
E
F
G
H
J
K
L
MA
B
BL

11. Remove the TORX bolt (T30) of the outside handle bracket.
12. While pulling outside handle bracket, slide toward front of vehi-
cle to remove outside handle bracket.
13. Reach to separate outside handle cable connection.
14. Remove the TORX bolts (T30) of door lock assembly.
15. Disconnect connectors of caught part and door lock assembly, and then remove door lock assembly. :5.8 N·m (0.59 kg-m, 51 in-lb)
PIIB0295E
PIIB0580E
MIIB0134E
MIIB0132E

BL-126
FRONT DOOR LOCK

INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:

Install each rod by rotating the rod holder until it engages with a tactile feel.

Before installing door lock assembly, apply Anti-Corrosion Wax M-97 Super or equivalent onto
mounting seat on the body.

When installing door lock assembly, be careful so that the outside handle cable bends as shown in
the figure.

Place the outside handle cable on the front of door lock
assembly before installing.
Disassembly and AssemblyBIS000XX
DOOR KEY CYLINDER ASSEMBLY
Removal
Remove the key cylinder escutcheon pawl and remove the door key cylinder.
Installation
Install in the reverse order of removal.
1. Door lock assembly
PIIB0296E
PIIB0284E
1. Door key cylinder assembly 2. Key cylinder escutcheon 3. Door key cylinder
PIIA6431E

FRONT DOOR LOCK
BL-127
C
D
E
F
G
H
J
K
L
MA
B
BL

OUTSIDE HANDLE
Removal
1. Remove handle cover screws.
2. Remove handle cover, and then remove door antenna. (Vehicles with intelligent key systems only)
Installation
Install in the reverse order of removal.
1. Outside handle 2. Screw 3. Handle cover
4. Door request switch 5. Pawl 6. Door antenna
PIIB0285E

BL-128
REAR DOOR LOCK

REAR DOOR LOCKPFP:82502
Component StructureBIS000XY
Removal and InstallationBIS000XZ
REMOVAL
1. Remove the rear door finisher. Refer to EI-35, "DOOR FINISHER" .
2. Disconnect inside handle cable and lock knob cable from inside handle.
CAUTION:
During removal and installation, work so as not to bend the
ends of the lock knob cable and inside handle cable.
3. Remove the rear door sealing, glass and corner piece assembly. Refer to GW-50, "
REAR DOOR GLASS
AND REGULATOR" .
4. Remove door side grommet, and remove outside handle escutcheon bolt (TORX T30) from grommet
hole.
1. Outside handle 2. Front gasket 3. TORX bolt (T30)
4. Inside handle 5. Screw 6. Lock knob cable
7. Inside handle cable 8. Door lock assembly 9. Outside handle cable
10. Outside handle bracket 11. TORX bolt (T30) 12. TORX bolt (T30)
13 Grommet 14. Rear gasket 15. Outside handle escutcheon
PIIB0286E
PIIA0632E

REAR DOOR LOCK
BL-129
C
D
E
F
G
H
J
K
L
MA
B
BL

CAUTION:
Do not forcibly remove the TORX bolts (T30).
5. While pulling the outside handle, remove outside handle
escutcheon.
6. While pulling outside handle, slide toward rear of vehicle to
remove outside handle.
7. Remove the front gasket and rear gasket.
8. Remove the TORX bolt (T30), and remove the outside handle
bracket.
MIIB0128E
SIIA1752E
MIIB0130E
: 5.8 N·m (0.59 kg-m, 51 in-lb)
PIIB0295E

BL-130
REAR DOOR LOCK

9. While pulling outside handle, slide toward front of vehicle to
remove outside handle bracket.
10. Reach to separate outside handle cable connection.
11. Remove the TORX bolts (T30) of door lock assembly.
12. Disconnect the door lock actuator connector and remove door lock assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:

To install each rod, be sure to rotate the rod holder until a click is felt.

Before installing door lock assembly, apply Anti-Corrosion Wax M-97 Super or equivalent onto
mounting seat on the body.

Place the outside handle bracket cable on the rear of door lock assembly before installing.
PIIB0580E
MIIB0134E
MIIB0132E

TRUNK LID
BL-131
C
D
E
F
G
H
J
K
L
MA
B
BL

TRUNK LIDPFP:H4300
Fitting AdjustmentBIS000Y0
LONGITUDINAL AND LATERAL CLEARANCE ADJUSTMENT
1. With the striker released, loosen the trunk lid hinge mounting bolts and close the trunk lid.
2. Make the lateral clearance and the clearance to the rear window glass equal, and open the trunk lid to
tighten the mounting bolts to the specified torque.
3. Finally tighten the striker mounting bolts to the specified torque.
SURFACE HEIGHT ADJUSTMENT
1. Loosen the striker mounting bolts. Raise the striker to the top position, and temporarily tighten the upper
mounting bolt at the position.
2. Close the trunk lid lightly and adjust the surface height, then open the trunk lid to finally tighten the striker
mounting bolts to the specified torque.
1. Trunk lid 2. Rear fender 3. Rear combination lamp
4. Rear bumper facie 5. Trunk lid hinge 6. Bolts
7. Trunk lid striker 8. Bolts
PIIB0287E

BL-132
TRUNK LID

Removal and Installation of Trunk Lid AssemblyBIS000Y1
REMOVAL
1. Disconnect the connectors in the trunk lid, and remove the har-
ness clamps to pull the harness out of the trunk lid.
2. Insert flat-bladed screwdriver into the gap and remove holder.
1. Trunk lid assembly 2. Trunk lid hinge 3. emergency lever
4. Trunk lid stay 5. Trunk lid finisher 6. Trunk lid lock
PIIB0288E
PIIB0289E
SIIA1561E