Key NISSAN TEANA 2014 Owner's Guide

BCS
BCM (BODY CONTROL MODULE)BCS-51
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
Priority DTC
1 • B2562: LOW VOLTAGE
2 • U1000: CAN COMM CIRCUIT
• U1010: CONTROL UNIT (CAN)
3 • B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
• B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
• B2196: DONGLE UNIT
• B2198: NATS ANTENNA AMP
4 • B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP SW
• B2605: PNP SW
• B2608: STARTER RELAY
• B260A: IGNITION RELAY
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B261A: PUSH-BTN IGN SW
• B261B: RES ENG RUN
• B261E: VEHICLE TYPE
• B26F1: IGNITION RELAY
• B26F2: IGNITION RELAY
•B26F6: BCM
• B26FD: SHIFT LOCK SOLENOID
• B26FE: HOOD SWITCH
• B26FF: INTELLIGENT TUNER
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-52
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
DTC Index
INFOID:0000000009462019
NOTE: Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni- tion switch OFF → ON again.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it . It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
5 • C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL
• C1730: FLAT TIRE FL
• C1731: FLAT TIRE FR
• C1732: FLAT TIRE RR
• C1733: FLAT TIRE RL
• C1734: CONTROL UNIT
• C1735: IGNITION SIGNAL
6 • B2621: INSIDE ANTENNA
• B2622: INSIDE ANTENNA
7 B259A: ROOM LAMP FUSE
Priority DTC
CONSULT display Fail-safe
Intelligent Key
warning lamp ON Tire pressure
monitor warning lamp ON Reference page
No DTC is detected.
Further testing may be required. —— — —
U1000: CAN COMM CIRCUIT — — — BCS-68, "Description"
U1010: CONTROL UNIT (CAN) — — — BCS-69, "DTC Logic"
U0415: VEHICLE SPEED SIG — — —BCS-70, "Description"
B2190: NATS ANTENNA AMP×—— SEC-84, "Description"
B2191: DIFFERENCE OF KEY ×—— SEC-86, "Description"
B2192: ID DISCORD BCM-ECM ×—— SEC-87, "DTC Logic"
B2193: CHAIN OF BCM-ECM ×—— SEC-88, "DTC Logic"
B2195: ANTI SCANNING ×—— SEC-89, "DTC Logic"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS
BCM (BODY CONTROL MODULE)BCS-53
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
B2196: DONGLE UNIT — — —
SEC-90, "Description"
B2198: NATS ANTENNA AMP. — — — SEC-92, "DTC Logic"
B2555: STOP LAMP — — —SEC-94, "DTC Logic"
B2556: PUSH-BTN IGN SW —×— SEC-97, "DTC Logic"
B2557: VEHICLE SPEED — ×— SEC-99, "DTC Logic"
B2560: STARTER CONT RELAY ××—SEC-100, "Description"
B2562: LOW VOLTAGE ×—— BCS-71, "DTC Logic"
B259A: ROOM LAMP FUSE — — — BCS-72, "DTC Logic"
B2601: SHIFT POSITION —×—SEC-101, "DTC Logic"
B2602: SHIFT POSITION — ×—SEC-104, "DTC Logic"
B2603: SHIFT POSI STATUS — ×—SEC-106, "DTC Logic"
B2604: PNP SW — ×—SEC-110, "DTC Logic"
B2605: PNP SW — ×—SEC-113, "DTC Logic"
B2608: STARTER RELAY ××—SEC-116, "DTC Logic"
B260A: IGNITION RELAY ××—PCS-58, "DTC Logic"
B2614: ACC RELAY CIRC — ×— PCS-60, "DTC Logic"
B2615: BLOWER RELAY CIRC — ×— PCS-62, "DTC Logic"
B2616: IGN RELAY CIRC — ×— PCS-64, "DTC Logic"
B2617: STARTER RELAY CIRC ××—SEC-118, "Description"
B2618: BCM ××—PCS-66, "DTC Logic"
B261A: PUSH-BTN IGN SW — ×— PCS-68, "DTC Logic"
B261B: RES ENG RUN — — — DLK-87, "DTC Logic"
B261E: VEHICLE TYPE××
(Turn ON for
15 seconds) —
SEC-120, "Description"
B2621: INSIDE ANTENNA — — — DLK-88, "DTC Logic"
B2622: INSIDE ANTENNA — — —DLK-90, "DTC Logic"
B26F1: IGNITION RELAY — — —PCS-70, "DTC Logic"
B26F2: IGNITION RELAY — — —PCS-72, "DTC Logic"
B26F6: BCM — — —PCS-74, "DTC Logic"
B26FD: SHIFT LOCK SOLENOID — — — DLK-92, "DTC Logic"
B26FE: HOOD SWITCH — — —DLK-95, "DTC Logic"
B26FF: REMOTE KEYLESS ENTRY RE-
CEIVER —— —
DLK-97, "DTC Logic"
C1704: LOW PRESSURE FL — — ×
WT-28, "DTC Logic"
C1705: LOW PRESSURE FR — — ×
C1706: LOW PRESSURE RR — — ×
C1707: LOW PRESSURE RL — — ×
C1708: [NO DATA] FL — — ×
WT-30, "DTC Logic"
C1709: [NO DATA] FR — — ×
C1710: [NO DATA] RR — — ×
C1711: [NO DATA] RL — — ×
CONSULT display Fail-safe
Intelligent Key
warning lamp
ON Tire pressure
monitor warning
lamp ON Reference page
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-54
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
C1712: [CHECKSUM ERR] FL — —
×
WT-33, "DTC Logic"
C1713: [CHECKSUM ERR] FR — — ×
C1714: [CHECKSUM ERR] RR — — ×
C1715: [CHECKSUM ERR] RL — — ×
C1716: [PRESSDATA ERR] FL — — ×
WT-35, "DTC Logic"
C1717: [PRESSDATA ERR] FR — — ×
C1718: [PRESSDATA ERR] RR — — ×
C1719: [PRESSDATA ERR] RL — — ×
C1720: [CODE ERR] FL — — ×
WT-37, "DTC Logic"
C1721: [CODE ERR] FR — — ×
C1722: [CODE ERR] RR — — ×
C1723: [CODE ERR] RL — — ×
C1724: [BATT VOLT LOW] FL — — ×
WT-39, "DTC Logic"
C1725: [BATT VOLT LOW] FR — — ×
C1726: [BATT VOLT LOW] RR — — ×
C1727: [BATT VOLT LOW] RL — — ×
C1729: VHCL SPEED SIG ERR — — ×WT-41, "DTC Logic"
C1730: FLAT TIRE FL — — ×
WT-42, "DTC Logic"
C1731: FLAT TIRE FR — — ×
C1732: FLAT TIRE RR — — ×
C1733: FLAT TIRE RL — — ×
C1734: CONTROL UNIT — — ×WT-44, "DTC Logic"
C1735: IGNTION SIGNAL — — ×WT-46, "DTC Logic"
CONSULT display Fail-safe Intelligent Key
warning lamp
ON Tire pressure
monitor warning
lamp ON Reference page
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-66
< BASIC INSPECTION >[BCM]
INSPECTION AND ADJUSTMENT
CONFIGURATION (BCM) : Configuration list
INFOID:0000000009462025
CAUTION:
Thoroughly read and understand the vehicle specifi cation. Incorrect settings may result in abnormal
control of ECU.
⇔ : Items which confirm vehicle specifications MANUAL SETTING ITEM
Items Setting value
AUTO LIGHT WITHOUT ⇔ MODE1 ⇔ MODE2 ⇔ MODE3 ⇔ MODE4 ⇔ MODE5
FR FOG LAMP WITHOUT ⇔ MODE1 ⇔ MODE2
TIRE PRESSURE 220kPa ⇔ 230kPa ⇔ 240kPa
BCM AC CONTROL MODE1 ⇔ MODE2
Key Fob Type ENST/LCK/UNLCK/ALRM
⇔ ENST/LCK/UNLCK/BD/ALRM ⇔
ENST/LCK/UNLCK/TRK/ALRM ⇔ LCK/UNLCK/PBD/ALRM ⇔
LCK/UNLCK/ALRM ⇔ LCK/UNLCK/PBD ⇔ LCK/UNLCK/TRNK ⇔
LCK/UNLCK ⇔ LCK/UNLCK/TRNK/ALRM
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BCS-80
< REMOVAL AND INSTALLATION >[BCM]
BCM (BODY CONTROL MODULE)
REMOVAL AND INSTALLATION
BCM (BODY CONTROL MODULE)
Removal and InstallationINFOID:0000000009462044
REMOVAL
CAUTION:
Before replacing BCM, perform "READ CONFIGURATI ON" to save or print current vehicle specifica-
tion. Refer to BCS-64, "ADDITIONAL SERVICE WHEN R EPLACING CONTROL UNIT : Description"
.
1. Disconnect the negative battery terminal. Refer to PG-73, "Removal and Installation (Battery)"
.
2. Remove the combination meter. Refer to MWI-82, "Removal and Installation"
.
3. Remove the BCM screws (A) and pull out the BCM (1).
4. Disconnect the harness connectors from the BCM (1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Be sure to perform "WRITE CONFIGURA TION" when replacing BCM. Refer to BCS-65, "CONFIGURA-
TION (BCM) : Description".
• Be sure to perform the system initializati on (NATS) when replacing BCM. Refer to BCS-64, "ADDI-
TIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description".
• When replacing BCM, if new BCM does not come wi th keyfobs attached, all existing keyfobs must be
re-registered.
ALMIA0580ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-35
< SYSTEM DESCRIPTION > [VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
N
O P
× : Applicable
–: Not applicable N POSI SIG
(On/Off) ––
×Neutral position (On/Off) judged by transmission
range switch signal.
P POSI SIG
(On/Off) ––
×Park position (On/Off) judged by transmission range
switch signal.
ACCEL POS SIG
(%) ×
– ×Throttle valve open/close status judged by CAN com-
munication signal is displayed.
SIDE G-SENSOR
(m/s
2) ×
– ×Transverse acceleration detected by side G-sensor is
displayed.
STR ANGLE SIG
(deg) ×
– ×Steering angle detected by steering angle sensor is
displayed.
PRESS SENSOR
(bar) ×
– ×Brake pressure detected by pressure sensor is dis-
played.
EBD SIGNAL
(On/Off) ––
×EBD operation (On/Off) status is displayed.
ABS SIGNAL
(On/Off) ––
×ABS operation (On/Off) status is displayed.
TCS SIGNAL
(On/Off) ––
×TCS operation (On/Off) status is displayed.
VDC SIGNAL
(On/Off) ––
×VDC operation (On/Off) status is displayed.
EBD FAIL SIG
(On/Off) ––
×EBD fail signal (On/Off) status is displayed.
ABS FAIL SIG
(On/Off) ––
×ABS fail signal (On/Off) status is displayed.
TCS FAIL SIG
(On/Off) ––
×TCS fail signal (On/Off) status is displayed.
VDC FAIL SIG
(On/Off) ––
×VDC fail signal (On/Off) status is displayed.
CRANKING SIG
(On/Off) ––
×The input state of the key SW START position signal
is displayed.
FLUID LEV SW
(On/Off) ×
– ×Brake fluid level switch (On/Off) status is displayed.
PARK BRAKE SW
(On/Off) ×
– ×Park brake switch (On/Off) status is displayed.
USV[FL-RR]
(On/Off) ——
×Primary side USV solenoid valve (On/Off) status is
displayed.
USV[FR-RL]
(On/Off) ——
×Secondary side USV solenoid valve (On/Off) status is
displayed.
HSV[FL-RR]
(On/Off) ——
×Primary side HSV solenoid valve (On/Off) status is
displayed.
HSV[FR-RL]
(On/Off) ——
×Secondary side HSV solenoid valve (On/Off) status is
displayed.
V/R OUTPUT
(On/Off) ——
×Valve relay operation signal (On/Off) status is dis-
played.
M/R OUTPUT
(On/Off) ——
×Motor relay operation signal (On/Off) status is dis-
played.
ENGINE RPM
(tr/min) ×
– ×Engine speed judged by CAN communication signal
is displayed.
Item
(Unit) Data monitor item selection
Remarks
ECU INPUT
SIGNALS MAIN
SIGNALS SELECTION
FROM MENU
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
DIAGNOSIS AND REPAIR WORK FLOWDAS-33
< BASIC INSPECTION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
Utilize a work sheet sample to organize all of the information for troubleshooting.
KEY POINTS• WHAT..... System and functions
• WHEN..... Date, Frequencies
• WHERE..... Road conditions
• HOW..... Operating conditions, Symptoms
WORK SHEET SAMPLE
ALOIA0189GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS-102
< BASIC INSPECTION >[LDW]
DIAGNOSIS AND REPAIR WORK FLOW
Utilize a work sheet sample to organize all of the information for troubleshooting.
KEY POINTS• WHAT..... System and functions
• WHEN..... Date, Frequencies
• WHERE..... Road conditions
• HOW..... Operating conditions, Symptoms
WORK SHEET SAMPLE
ALOIA0189GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DAS
DIAGNOSIS AND REPAIR WORK FLOWDAS-177
< BASIC INSPECTION > [BSW]
C
D E
F
G H
I
J
K L
M B
N P
A
Utilize a work sheet sample to organize all of the information for troubleshooting.
KEY POINTS• WHAT..... System and functions
• WHEN..... Date, Frequencies
• WHERE..... Road conditions
• HOW..... Operating conditions, Symptoms
WORK SHEET SAMPLE
ALOIA0193GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM