NISSAN VERSA 2006 Workshop Service Repair Manual

DRIVER AIR BAG MODULE
SRS-43
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: June 20062007 Versa
CAUTION:

Make sure driver air bag module harness (1) is routed prop-
erly to avoid SRS component damage during installation.
LHIA0112E

SRS-44
SPIRAL CABLE
Revision: June 20062007 Versa
SPIRAL CABLEPFP:25554
Removal and InstallationEHS001UE
REMOVAL
WAR NIN G:
When servicing the SRS, do not work from directly in front of air bag module.
CAUTION:

Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at
least 3 minutes.

Do not tap or bump the steering wheel.

Do not disassemble the spiral cable.

Do not allow oil, grease or water to come in contact with the spiral cable.

Replace the spiral cable if it has been dropped or sustained an impact.

With the steering linkage disconnected, the spiral cable may snap by turning the steering wheel
beyond the limited number of turns. The spiral cable can be turned counterclockwise about 2.5
turns from the neutral position.
1. Disconnect the negative and positive battery cables, then wait at least 3 minutes.
2. Set the front wheels to the straight-ahead/neutral position.
3. Remove the steering wheel. Refer to PS-6, "
STEERING WHEEL" .
4. Remove the column cover upper and lower.
LHIA0113E
1. Nut, refer to PS-6, "STEERING
WHEEL"
2. Steering wheel 3. Lighting and turn signal switch
4. Spiral cable 5. Driver air bag module connectors 6. Wiper and washer switch
7. Column cover lower 8. Steering lock escutcheon 9. Steering column assembly
10. Column cover upper Pawl

SPIRAL CABLE
SRS-45
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: June 20062007 Versa
5. Disconnect wiper and washer switch connector (1). Then while
pressing tabs (2), pull wiper and washer switch away from spiral
cable to remove.
6. Disconnect lighting and turn signal switch connector (1). Then
while pressing tabs (2), pull lighting and turn signal switch
toward driver door to remove.
7. Remove the screws, then release the tab at the top and pull the
spiral cable away from the steering column assembly.
8. Disconnect spiral cable connectors.
INSTALLATION
Installation is in the reverse order of removal.

Align spiral cable correctly when installing steering wheel, refer
to PS-6, "
STEERING WHEEL" . Make sure spiral cable align-
ment and centering marks (B) are matched and in the neutral
position. The neutral position is detected by turning left 2.6 revo-
lutions from the right end position, ending with the locating pin
(A) at the top. Place steering wheel in straight ahead position,
then install it with the locating pin hole (C) directly over spiral
cable locating pin.

After the work is completed, perform self-diagnosis to make sure
no malfunction is detected. Refer to SRS-21, "
SRS Operation
Check" .
WHIA0315E
WHIA0316E
PHIA1024J

SRS-46
FRONT PASSENGER AIR BAG MODULE
Revision: June 20062007 Versa
FRONT PASSENGER AIR BAG MODULEPFP:K8515
Removal and InstallationEHS001UF
REMOVAL
WAR NIN G:

When servicing the SRS, do not work from directly in front of air bag module.

Always place front passenger air bag module with pad side facing upward.
CAUTION:

Before servicing SRS, turn the ignition switch OFF, disconnect both battery cables and wait at
least 3 minutes.

Do not use old bolts after removal; replace with new bolts.

Do not insert any foreign objects (screwdriver, etc.) into air bag module or harness connectors.

Do not disassemble air bag module.

Do not expose the front passenger air bag module to temperatures exceeding 90°C (194°F).

Replace the front passenger air bag module if it has been
dropped or sustained an impact.

Do not allow oil, grease or water to come in contact with the
front passenger air bag module.
1. Disconnect the negative and positive battery cables, then wait at least 3 minutes.
2. Remove the side ventilator assembly (right). Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
3. Disconnect front passenger air bag module connector (1) and
remove the upper instrument panel assembly bolts (2).
⇐: Vehicle front
4. Remove the front passenger air bag module bolts (3) from the
steering member.
5. Release the pawls and remove the front passenger air bag mod-
ule (1) from the upper instrument panel assembly (2).
INSALLATION
Installation is in the reverse order of removal.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRS-21, "
SRS Operation Check" .
WHIA0321E
WHIA0317E
WHIA0318E

SIDE CURTAIN AIR BAG MODULE
SRS-47
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: June 20062007 Versa
SIDE CURTAIN AIR BAG MODULEPFP:985P0
Removal and InstallationEHS001UG
REMOVAL
WA RN ING:

When servicing the SRS, do not work from directly in front of air bag module.

Always place the curtain air bag module with deployment side facing upward.

Do not reuse center pillar upper garnish if removed.
CAUTION:

Before servicing SRS, turn the ignition switch OFF, disconnect both battery cables and wait at
least 3 minutes.

Do not use old bolts after removal; replace with new bolts.

Do not insert any foreign objects (screwdriver, etc.) into air bag module or harness connectors.

Do not disassemble air bag module.

Do not expose the side curtain air bag module to temperatures exceeding 90°C (194°F).

Replace the side curtain air bag module if it has been
dropped or sustained an impact.

Do not allow oil, grease or water to come in contact with the
side curtain air bag module.

Do not attempt to repair or replace damaged direct-connect
SRS component connectors. If a direct-connect harness
connector is damaged, the harness must be replaced.
1. Disconnect both the negative and positive battery cables, then wait at least 3 minutes.
2. Remove the headlining. Refer to EI-39, "
HEADLINING" .
WHIA0319E
1. Side curtain air bag module 2. Inflator 3. Ground bolt
⇐Vehicle front
WHIA0321E

SRS-48
SIDE CURTAIN AIR BAG MODULE
Revision: June 20062007 Versa
3. Disconnect side curtain air bag module connector.
NOTE:
For removal/installation of the direct-connect SRS connectors,
refer to SRS-8, "
Direct-connect SRS Component Connectors" .
4. Remove the bolts in order starting at the front or rear, then
remove the side curtain air bag module.
INSTALLATION
Installation is in the reverse order of removal.

For removal/installation of the direct-connect SRS connectors, refer to SRS-8, "Direct-connect SRS Com-
ponent Connectors" .

After replacement of side curtain air bag module, perform self-diagnosis to check that no malfunction is
detected. Refer to SRS-21, "
SRS Operation Check" .
PHIA0953J

CRASH ZONE SENSOR
SRS-49
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: June 20062007 Versa
CRASH ZONE SENSORPFP:98531
Removal and InstallationEHS001UH
REMOVAL
CAUTION:

Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at
least 3 minutes.

Do not disassemble the crash zone sensor.

Do not use old nuts after removal; replace with new nuts.

Replace the crash zone sensor if it has been dropped or
sustained an impact.

Check crash zone sensor to make sure it is free of deformi-
ties, dents, cracks or rust. If it shows any visible signs of
damage, replace it with a new one.
1. Disconnect both the negative and positive battery cables, then wait at least 3 minutes.
2. Remove upper radiator cover and front grille, refer to EI-19, "
FRONT GRILLE" .
3. Disconnect crash zone sensor harness connector (1).
4. Remove the nuts (2) and remove the crash zone sensor (3).
INSTALLATION
Installation is in the reverse order of removal.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRS-21, "
SRS Operation Check" .
WHIA0321E
WHIA0320E

SRS-50
SIDE AIR BAG (SATELLITE) SENSOR
Revision: June 20062007 Versa
SIDE AIR BAG (SATELLITE) SENSORPFP:98830
Removal and InstallationEHS001UI
REMOVAL
WAR NIN G:
Do not reuse center pillar upper garnish if removed.
CAUTION:

Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at
least 3 minutes.

Do not disassemble the side air bag (satellite) sensor.

Do not use old nuts after removal; replace with new nuts.

Replace the side air bag (satellite) sensor if it has been
dropped or sustained an impact.

Check side air bag (satellite) sensor to make sure it is free
of deformities, dents, cracks or rust. If it shows any visible
signs of damage, replace it with a new one.
1. Disconnect both the negative and positive battery cables, then wait at least 3 minutes.
2. Remove the front seat belt retractor. Refer to SB-3, "
Removal and Installation of Front Seat Belt" .
3. Remove the nuts (1) and remove side air bag (satellite) sensor
(2).
⇐: Vehicle front
4. Disconnect the side air bag (satellite) sensor harness connector
(3).
INSTALLATION
Installation is in the reverse order of removal.

After the work is completed, perform self-diagnosis to make sure no malfunction is detected. Refer to
SRS-21, "
SRS Operation Check" .
WHIA0321E
WHIA0322E

FRONT SEAT BELT PRE-TENSIONER
SRS-51
C
D
E
F
G
I
J
K
L
MA
B
SRS
Revision: June 20062007 Versa
FRONT SEAT BELT PRE-TENSIONERPFP:86884
Removal and InstallationEHS001UJ
For removal and installation procedures, refer to SB-3, "Removal and Installation of Front Seat Belt" .

SRS-52
DIAGNOSIS SENSOR UNIT
Revision: June 20062007 Versa
DIAGNOSIS SENSOR UNITPFP:28556
Removal and InstallationEHS001UK
REMOVAL
WAR NIN G:
Before disconnecting diagnosis sensor unit harness connector(s), be sure to disconnect harness con-
nectors from air bag modules and front seat belt pre-tensioner to prevent deployment by static elec-
tricity.
CAUTION:

Before servicing the SRS, turn the ignition switch OFF, disconnect both battery cables and wait at
least 3 minutes.

Do not disassemble diagnosis sensor unit.

Do not use old bolts; replace with new bolts.

Replace the diagnosis sensor unit if it has been dropped or sustained an impact.

Check diagnosis sensor unit bracket to make sure it is free of deformities, dents, cracks or rust. If
it shows any visible signs of damage, replace with new one.

The diagnosis sensor unit must always be installed with the arrow mark "⇐" pointing toward the
front of the vehicle for proper operation.
1. Disconnect the negative and positive battery cables, then wait at least 3 minutes.
2. Disconnect the harness connectors for each air bag module and seat belt pre-tensioner. Refer to SRS-41,
"DRIVER AIR BAG MODULE" , SRS-46, "FRONT PASSENGER AIR BAG MODULE" , SRS-47, "SIDE
CURTAIN AIR BAG MODULE" , SRS-51, "FRONT SEAT BELT PRE-TENSIONER" .
3. Remove center console assembly. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
4. Disconnect diagnosis sensor unit connectors.
5. Remove the bolts and the ground bolt, then remove the diagnosis sensor unit.
INSTALLATION
Installation is in the reverse order of removal.

The diagnosis sensor unit must always be installed with the arrow mark "⇐" pointing toward the front of
the vehicle.

Follow the tightening sequence 1,2,3,4 as shown.

After the work is completed, perform self-diagnosis to check that no malfunction is detected. Refer to
SRS-21, "
SRS Operation Check" .
ECU DISCRIMINATED NO.
After replacing the diagnosis sensor unit, confirm that the diagnosis sensor unit identification is correct for the
vehicle as equipped. Refer to SRS-19, "
CONSULT-II Function (AIR BAG)" .
1. Diagnosis sensor unit connectors 2. Ground Bolt 3. Bolt
4. Diagnosis sensor unit⇐Vehicle front
WHIA0323E