NISSAN X-TRAIL 2005 Service Repair Manual

FRONT WIPER AND WASHER SYSTEM
WW-9
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation of Front Wiper Drive Assembly EKS0032R
REMOVAL
1. Operate wiper motor, and stop it at the upper limit position.
2. Remove front wiper arm from the vehicle.
3. Remove the cowl top cover. Refer to EI-20, "
COWL TOP" .
1. Rubber 2. Wiper frame 3. Wiper link
4. Motor arm 5. Wiper Motor 6. Rubber
7. Wiper link . .
1. Rubber 2. Wiper frame 3. Wiper link
4. Motor arm 5. Wiper Motor 6. Rubber
7. Wiper link . .
PKIC0593E
PKIC0594E

WW-10
FRONT WIPER AND WASHER SYSTEM

4. Remove 4 screws and remove front wiper drive assembly from
the vehicle.
5. Disconnect front wiper motor connector.
6. Remove wiper link from wiper frame.
7. Remove motor arm from wiper motor.
8. Remove front wiper motor from wiper frame.
INSTALLATION
1. Connect front wiper motor to connector. Turn the front wiper
switch ON to operate front wiper motor, then turn the front wiper
switch OFF (auto stop).
2. Disconnect wiper motor connector.
3. Install front wiper motor to the wiper frame.
4. Install front wiper drive assembly to the vehicle.
5. Install wiper link to the wiper motor arm.
6. Connect front wiper motor connector. Turn the front wiper switch
ON to operate the front wiper motor, then turn wiper switch OFF
(auto stop)
7. Rotate motor arm to the upper limit position.
8. Install front wiper drive assembly to the vehicle.
9. Turn the front wiper switch ON to operate the Wiper motor, then
turn front wiper switch OFF (auto stop)
10. Install cowl top cover. Refer to EI-20, "
COWL TOP" .
11. Install wiper arm to the vehicle.
CAUTION:

Never drop the wiper motor or cause it to contact other parts.

Check the grease conditions of the motor arm and wiper link joint (at retainer). Apply grease if
necessary.
SKIA0016E
PKIA0475E
Motor arm mounting
nut : 17.7 N·m (1.8 kg-m, 13 ft-lb)
Wiper motor mount-
ing screw : 4.5 N·m (0.46 kg-m, 40 in-lb)
Front wiper drive
assembly mounting
bolt : 7.7 N·m (0.79 kg-m, 68 in-lb)
SKIA0092E
PKIA0476E

FRONT WIPER AND WASHER SYSTEM
WW-11
C
D
E
F
G
H
I
J
L
MA
B
WW

Front Washer Nozzle AdjustmentEKS0032S
Adjust front washer nozzle with suitable tool as shown in the figure.
Unit: mm (in)
NOTE:
*: The diameters of these circles are less than 80 mm (3.15 in).
Washer Tube LayoutEKS0032T
Adjustable range : ±10° (In any direction)
PKIA0478E
*1 395 (15.55) *5 100 (3.94)
*2 395 (15.55) *6 100 (3.94)
*3 395 (15.55) *7 400 (15.88)
*4 395 (15.55) *8 400 (15.88)
PKIA5764E
PKIA5765E
PKIA0539E

WW-12
FRONT WIPER AND WASHER SYSTEM

Removal and Installation of Front Washer Nozzle EKS0032U
REMOVAL
Push front washer nozzle pawl toward engine hood to pull out.
INSTALLATION
1. After connecting washer hose, press nozzle from cowl top cover surface.
2. Assemble nozzle and socket.
3. Adjust nozzle injection position.
Inspection for Front Washer Nozzle EKS0032V
CHECK VALVE
Blow air in the injection direction, and check that air flows only one
way. Make sure that the reverse direction (inhale) is not possible.
Removal and Installation of Wiper and Washer Switch EKS0032W
REMOVAL
1. Remove steering column cover. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" in “INSTRUMENT PANEL (IP)” section.
2. Remove wiper and washer switch connector.
3. Remove two screws then remove wiper and washer switch from
the spiral cable.
INSTALLATION
Installation is the reverse order of removal.
PKIA9740E
PKIA9741E
SKIA0018E

FRONT WIPER AND WASHER SYSTEM
WW-13
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation of Washer Tank EKS0032X
REMOVAL
1. Remove washer tank inlet mounting screw and pull out washer
tank inlet.
2. Remove fender protector. Refer to EI-21, "
FENDER PROTEC-
TOR" .
3. Remove washer motor connector.
4. Remove washer tank mounting screw and pawl.
5. Remove washer hose, and remove the washer tank from the
vehicle.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
After installation, add water up to the upper level of the washer tank inlet, and check for water leaks.
Removal and Installation of Washer Motor EKS0032Y
REMOVAL
1. Remove fender protector. Refer to EI-21, "FENDER PROTECTOR"
2. Remove washer motor connector and hose.
3. Pull out washer motor in the direction of the arrow in the figure,
and remove the washer motor from the washer tank.
INSTALLATION
Installation is the reverse order of removal.
CAUTION:
When installing washer motor, there should be no packing twists, etc.
PKIA0484E
PKIA8885E
Washer tank mounting screw
: 4.5 N·m (0.46 kg-m, 40 in-lb)
PKIC0591E

WW-14
REAR WIPER AND WASHER SYSTEM

REAR WIPER AND WASHER SYSTEMPFP:28710
Wiring Diagram — WIP/R —EKS0032Z
TKWA1556E

REAR WIPER AND WASHER SYSTEM
WW-15
C
D
E
F
G
H
I
J
L
MA
B
WW

TKWA1557E

WW-16
REAR WIPER AND WASHER SYSTEM

Terminal and Reference Values for Combination SwitchEKS00330
Removal and Installation of Rear Wiper Arms EKS00331
WIPER ARMS
1. Turn on wiper switch to operate wiper motor and then turn it
“OFF” (auto stop).
2. Lift the blade up and then set it down onto glass surface. Set the
black center to clearance “L” immediately before tightening the
nut.
3. Eject washer fluid. Turn on wiper switch to operate wiper motor
and then turn it “OFF”.
4. Ensure that wiper blades stop on the lowest heat wire.

Tighten wiper arm nut to specified torque.

Before reinstalling wiper arm, clean up the pivot area as illus-
trated. This will reduce possibility of wiper arm looseness.
Terminal
No.Wire
colorSignal name Measuring condition
Reference value
Ignition switch Condition or operation
21 WWiper motor
Operation signal (ON)ON Wiper switchOFF Battery voltage
ON Approx. 0V
22 LG/B Washer switch signal ON Wiper switchWASH Approx. 0V
OFF Battery voltage
23 BR/YWiper motor
Operation signalON Wiper switch: INT
24 B/W Ground OFF — —
SKIA0083J
Clearance “L” : 55.6 - 70.6 mm (2.189 - 2.780 in)
Rear wiper arm nuts
: 15.2 N·m (1.6 kg-m, 11 ft-lb)
SKIA0077E
SEL024J

REAR WIPER AND WASHER SYSTEM
WW-17
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation of Rear Wiper MotorEKS00332
REMOVAL
1. Remove the back door finisher. Refer to EI-34, "BACK DOOR TRIM" .
2. Disconnect wiper motor connector.
3. Remove wiper arm from the vehicle.
4. Remove wiper motor form the vehicle.
5. Remove rubber from the vehicle.
INSTALLATION
1. Install rubber to the vehicle.
2. Install wiper motor to the vehicle.
3. Connect wiper motor to connector. Turn the rear wiper switch ON to operate wiper motor, then turn the
rear wiper switch OFF (auto stop).
4. Install wiper arm to the vehicle.
5. Install back door finisher. Refer to EI-34, "
BACK DOOR TRIM" .
CAUTION:

Never drop the wiper motor or cause it to contact other parts.

Check the grease conditions of the motor arm and wiper link joint (at retainer). Apply grease if
necessary.
1. Wiper motor 2. Rubber 3. Nut cover
4. Wiper arm 5. Wiper blade
PKIA7846E
SKIA0040E
Rear wiper motor mounting bolt
: 4.5 N·m (0.46 kg-m, 40 in-lb)

WW-18
REAR WIPER AND WASHER SYSTEM

Rear Washer Nozzle AdjustmentEKS00333

Adjust rear washer nozzle with suitable tool as shown in the figure at left.
Unit: mm (in)
*: The diameter of this circle is less than 40 mm (1.57in).
Removal and Installation of Rear Washer Nozzle EKS00334
REMOVAL
1. Remove washer hose from rear washer nozzle.
2. Remove rear washer nozzle mounting screw and remove rear
washer nozzle.
INSTALLATION
1. After connecting washer hose, press nozzle from cowl top cover surface.
2. Assemble nozzle and socket.
3. Adjust nozzle injection position.
Inspection for Rear Washer Nozzle EKS00335
CHECK VALVE
Blow air in the injection direction, and check that air flows only one
way. Make sure that the reverse direction (inhale) is not possible. Adjustable range : ±10° (In any direction)
PKIA0487E
*H 90 (3.54)
* L 150 (5.91)
SKIA0091E
PKIA5552E
SKIA0042E