NISSAN X-TRAIL 2005 Service Repair Manual

REAR WIPER AND WASHER SYSTEM
WW-19
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation of Wiper and Washer Switch EKS00336
Refer to WW-12, "Removal and Installation of Wiper and Washer Switch" .
Removal and Installation of Washer Tank EKS00337
Refer to WW-13, "Removal and Installation of Washer Tank" .
Removal and Installation of Washer Motor EKS00338
Refer to WW-13, "Removal and Installation of Washer Motor" .
Washer Tube LayoutEKS00339
PKIA0540E

WW-20
HEADLAMP WASHER

HEADLAMP WASHERPFP:28620
System DescriptionEKS0036H
The headlamp washer is controlled by the headlamp washer timer. With power and ground supplied, the head-
lamp washer motor operates.
Power is supplied at all times

through 30A fusible link (letter E, located in fuse and fusible link box)

to headlamp washer motor terminal 1,

through 10A fuse (No. 31, located in fuse and fusible link box)

to lighting switch terminal 11.
With the ignition switch in the ON or START position, power is supplied (with xenon headlamp)

through 10A fuse [No. 11, located in fuse block (J/B)]

to headlamp washer timer terminal 4.
With the ignition switch in the ON or START position, power is supplied (without xenon headlamp)

through 10A fuse [No. 13, located in fuse block (J/B)]

to headlamp washer timer terminal 4.
Ground is supplied

to headlamp washer timer terminal 5

through grounds E24 and E50.
When headlamp washer switch is pushed during lighting switch is in 1ST or 2ND position, ground is supplied
(with xenon headlamp)

to headlamp washer motor terminal 2

through headlamp washer timer terminal 2,

to headlamp washer timer terminal 6

through front wiper and washer switch terminal 18

through front wiper and washer switch terminal 17

through grounds M24 and M50.
When headlamp washer switch is pushed during lighting switch is in 1ST or 2ND position, ground is supplied
(without xenon headlamp)

to headlamp washer motor terminal 2

through headlamp washer timer terminal 2,

to headlamp washer timer terminal 6

through headlamp washer switch terminal 2

through headlamp washer switch terminal 1

through grounds M27 and M70.
With power and ground supplied, the headlamp washer motor operates.

HEADLAMP WASHER
WW-21
C
D
E
F
G
H
I
J
L
MA
B
WW

Wiring Diagram —HLC—EKS0036I
TKWB1139E

WW-22
HEADLAMP WASHER

TKWB1140E

HEADLAMP WASHER
WW-23
C
D
E
F
G
H
I
J
L
MA
B
WW

Wiring Diagram —HLC—/RHD modelsEKS00ES9
TKWB1141E

WW-24
HEADLAMP WASHER

TKWB1142E

HEADLAMP WASHER
WW-25
C
D
E
F
G
H
I
J
L
MA
B
WW

Removal and Installation of Headlamp Washer NozzleEKS0036J
REMOVAL
1. Remove front bumper. Refer to EI-14, "FRONT BUMPER"
2. Remove hose clip and metal clip.
3. Remove headlamp washer nozzle from front bumper.
INSTALLATION
Installation is in the reverse order of removal.
Inspection for Headlamp Washer NozzleEKS0036K
CHECK VALVE
Blow air in the injection direction, and check that air flows only one
way. Make sure that the reverse direction is not possible.
Removal and Installation of Washer TankEKS0036L
Refer to WW-13, "Removal and Installation of Washer Tank" .
Removal and Installation of Washer MotorEKS0036M
1. Remove front bumper. Refer to EI-14, "FRONT BUMPER"
2. Remove washer motor connector and hose.
3. Pull out washer motor in the direction of the arrow in the figure,
and remove the washer motor from the washer tank.
CAUTION:
When installing washer motor, there should be no packing
twist, etc.
PKIA0490E
PKIA0491E
PKIC0596E

WW-26
HEADLAMP WASHER

Washer Tube LayoutEKS0036N
PKIC1040E

HORN
WW-27
C
D
E
F
G
H
I
J
L
MA
B
WW

HORNPFP:25610
Wiring Diagram — HORN —EKS0033A
TKWA1560E

WW-28
HORN

Removal and InstallationEKS0033B
REMOVAL
1. Remove the front grille. Refer to EI-19, "FRONT GRILLE"
2. Disconnect horn connector.
3. Remove horn.
INSTALLATION
Installation is the reverse order of removal.
SKIA0027E
Horn mounting bolt
: 17 N·m (1.7 kg-m, 13 ft-lb)