light OLDSMOBILE AURORA 1999 Owner's Manual

yellowblue
2-43 Fog Lamps
To turn on the fog lamps,
first turn on the parking
lamps or headlamps. Then
press the fog lamp switch
located on the left side of
the instrument panel. A
light will glow on the
switch when the fog lamps
are on. To turn off the fog
lamps, press it again.
The fog lamps will also turn off when you turn on your
high
-beam headlamps, but will turn on again when you
switch to low beams.
Cornering Lamps
The cornering lamps are designed to come on when you
signal a turn. This will provide more light for cornering
at night.
ProCarManuals.com

yellowblue
2-44 Twilight Sentinel


Twilight sentinel turns the
headlamps, taillamps and
parking lamps on and off
by sensing how dark it
is outside.
To operate it, leave the headlamp switch off and move
the twilight sentinel control toward MAX. The control is
located to the left of the steering column.
If you move the control all the way to MAX, your lamps will
remain on for three minutes after you turn off your engine. If
you move the control toward MIN, the lamps will go off
quickly when you turn off your engine. You can set this delay
time for only a few seconds or up to three minutes.
Light Sensor
Your twilight sentinel and daytime running lamps work
with the light sensor on top of the instrument panel.
Don't cover it up. If you do it will read ªdarkº and the
headlamps will come on.
Interior Lamps
Instrument Panel Brightness Control
You can brighten or dim your instrument cluster, radio and
climate control displays and control lights by rotating the
INTERIOR LIGHTS control between LO and HI when
your lights are on. Rotate the control all the way to HI and
you will turn on the interior courtesy lamps.
Courtesy Lamps
When any door is opened, several lamps go on. They
make it easy for you to enter and leave the car. To turn
on these lamps, rotate the INTERIOR LIGHTS knob all
the way to HI.
ProCarManuals.com

yellowblue
2-45 Illuminated Entry
Press the UNLOCK button on the remote lock control
transmitter and the interior courtesy lamps will come on
and stay on for up to one minute. The lamps will turn off
immediately by pressing the LOCK button on the
remote lock control transmitter, starting the ignition or
activating the power door locks.
Delayed Illumination
When you open the door to enter your vehicle, the
interior lamps will come on. When you close the door
with the ignition off, the interior lamps will stay on for
25 seconds or until the ignition is turned on. Note that
locking the doors with the power door lock switch will
override the delayed illumination feature and the lights
will turn off right away.
Theater Dimming
This feature allows for a three to five-second fade out of
the courtesy lamps instead of immediate turn off. They
will not fade if the interior lights switch is used.
Exit Lighting
With this feature, the interior lamps will come on for
25 seconds after you remove the key from the ignition.
This will give you time to find the door pull handle or
lock switches when you exit the vehicle.
Parade Dimming
This feature prohibits the dimming of your instrument
displays during daylight while your headlamps are on.
This feature operates with the light sensor for the
twilight sentinel and is fully automatic. When the light
sensor reads darkness outside, you will be able to dim
your instrument panel displays once again.
Perimeter Lighting
When the UNLOCK button on the remote lock control
transmitter is pressed, the headlamps, parking lamps,
back
-up lamps and cornering lamps will come on if it is
dark enough outside according to the twilight sentinel.
This feature can be programmed on or off for each
driver's transmitter.
To turn the feature off:
1. Turn the ignition key to OFF.
2. Press and hold the door lock switch throughout this
procedure. All doors will lock.
ProCarManuals.com

yellowblue
2-46
3. Press the instant alarm button on the remote lock
control transmitter. Perimeter lighting remains on at
this time and the horn will chirp two times.
4. Press the instant alarm button on the remote lock
control transmitter again. Perimeter lighting is
disabled and the horn will chirp one time.
5. Release the door lock switch. The perimeter lighting
option is now off.
To turn the feature on:
1. Turn the ignition key to OFF.
2. Press and hold the door lock switch throughout this
procedure. All doors will lock.
3. Press the instant alarm button on the remote lock
control transmitter. Perimeter lighting remains off at
this time and the horn will chirp one time.
4. Press the instant alarm button on the transmitter
again. Perimeter lighting is now enabled and the
horn will chirp two times.
5. Release the door lock switch. The perimeter lighting
option is now on.
This procedure changes the mode for only the
transmitter used to change this setting. The procedure
will need to be repeated for the second transmitter.Front Reading Lamps
These lamps and the interior courtesy lamps will come
on when you open a door. They will turn off when you
turn on the ignition. If a door is left open, they will turn
off after about 10 minutes.
To turn on the reading lamps when the doors are closed,
press the button behind the lamp you want on. Press it
again to turn the lamp off.
These lamps work even when the ignition is off. To
avoid draining your vehicle's battery, be sure to turn
off all front and rear reading lamps when leaving
your vehicle.
ProCarManuals.com

yellowblue
2-47 Rear Reading Lamps
These lamps go on when you open the doors. You can
also turn them on by pressing the button to the side of
the lamp. Press it again to turn them off.
Trunk Lamp
When you open the trunk to its full open position, a
lamp will come on inside the trunk. This lamp will
automatically turn off when the trunk is closed.
Inadvertent Load Protection
This feature automatically shuts off the interior lamps
if any are left on for more than 10 minutes when the
ignition is off or a door is left open. This will keep
your battery from running down.
Mirrors
Electrochromic Day/Night Rearview Mirror
with Compass
Your vehicle may have an electrochromic inside
rearview mirror with a compass.
When set in the MIRROR position, this mirror
automatically changes to reduce glare from headlamps
behind you. A time delay feature prevents rapid
changing from the day to night positions while driving
under lights and through traffic.
The mirror also includes an eight
-point compass display in
the upper right corner of the mirror face. When on, the
compass automatically calibrates as the vehicle is driven.
ProCarManuals.com

yellowblue
2-48
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause
the liquid cleaner to enter the mirror housing. Use a
cotton swab and glass cleaner to clean the photocells
when necessary.
Mirror Operation
The right side of the button located at the bottom of the
mirror turns the electrochromic mirror on and off. To
turn on the automatic dimming feature, press MIRROR.
To turn off automatic dimming, press MIRROR again.
The green indicator light will be illuminated when this
feature is active.Compass Operation
Press the COMPASS button once to turn the compass
on or off.
When the ignition and the compass feature are on, the
compass will show two character boxes for
approximately two seconds. After two seconds, the
mirror will display the compass heading.
If, after two seconds, the display does not show a
compass heading (ªNº for North, for example), there
may be a strong magnetic field interfering with the
compass. Such interference may be caused by a
magnetic antenna mount, magnetic note pad holder or a
similar magnetic item.
Compass Calibration
If the letter ªCº should ever appear in the compass
window, the compass may need calibration.
The mirror can be calibrated in one of two ways:

Drive the vehicle in circles at five mph (8 km/h) or
less until the display reads a direction, or

Drive the vehicle on your everyday routine.
ProCarManuals.com

yellowblue
2-52 Convenience Net
Your vehicle has a convenience net just inside the back
wall of the trunk.
Put small loads, like grocery bags, behind the net. It can
help keep them from falling over during sharp turns or
quick starts and stops.
The net isn't for larger, heavier loads. Store them in the
trunk as far forward as you can. You can unhook the net
so that it will lie flat when you're not using it.
Two positions exist for the convenience net, depending
on the size of the cargo.
Use this position for small loads.
Use this position for slightly larger loads.
When installing the net in either position, be sure the
ªup labelº (A) is pointing up.
ProCarManuals.com

yellowblue
2-53
Ashtrays and Cigarette Lighter
Push and release the cover to reveal the front ashtray,
lighter and accessory power outlet.
NOTICE:
Don't put papers and other things that burn
into your ashtrays. If you do, cigarettes or
other smoking materials could set them on fire,
causing damage.
To open either rear ashtray, you may press and release
the cover.
To clean an ashtray, make sure the cover is open fully,
then lift out the ashtray by pulling on the snuffer.
To use a lighter, just push it in all the way and let go.
When it's ready, it will pop back by itself.
NOTICE:
Don't hold a cigarette lighter in with your hand
while it is heating. If you do, it won't be able to
back away from the heating element when it's
ready. That can make it overheat, damaging the
lighter and the heating element.
Sun Visors
To block out glare, you can swing down the visors. You
can also remove them from the center mount and swing
them to the side, while the auxiliary visor remains to
block glare from the front.
To extend the visor at the sides, pull out the extension.
Illuminated Visor Vanity Mirrors
When you open the cover to the driver or passenger side
visor vanity mirror, the lamps will come on. You can
adjust the brightness of the lamps with the switch by
sliding the lever up or down.
ProCarManuals.com

yellowblue
2-56
Universal Transmitter
This transmitter allows you to consolidate the functions
of up to three individual hand
-held transmitters. It will
operate garage doors and gates, or other devices
controlled by radio frequency such as home/office
lighting systems.The transmitter will learn and transmit the frequencies
of most current transmitters and is powered by your
vehicle's battery and charging system.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of
the device.
Changes and modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
ProCarManuals.com

yellowblue
2-57 Programming the Transmitter
Do not use the Universal Transmitter with any garage
door opener that does not have the ªstop and reverseº
safety feature. This includes any garage door opener
model manufactured before April 1, 1982.
Be sure that people and objects are clear of the garage
door you are programming.
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. If you have previously programmed a Universal
Transmitter channel, proceed to Step 2. Otherwise,
hold down the two outside buttons on the Universal
Transmitter until the indicator light begins to flash
rapidly (after 20 seconds). Then release the buttons.
This procedure initializes the memory and erases any
previous settings for all three channels.2. Decide which one of the three channels you want to
program. Hold the end of the hand-held transmitter
about 2 to 5 inches (5 to 13 cm) away from the
surface of the Universal Transmitter so that you can
still see the indicator light.
3. Using both hands, press the hand
-held transmitter
button and the desired button on the Universal
Transmitter. Continue to press both buttons
through Step 4.
4. Hold down both buttons until you see the indicator
light on the Universal Transmitter flash slowly and
then rapidly. The rapid flashing indicates that the
Universal Transmitter has been programmed.
Release both buttons once the indicator light starts
to flash rapidly.
ProCarManuals.com