light Oldsmobile Aurora 2001 s Workshop Manual

2-84
The DIC is used to program the personal choices of
two drivers. The drivers are recognized as DRIVER 1
and DRIVER 2. You will let the DIC and the vehicle
know which driver you are by using your remote lock
control transmitter or by pressing the appropriate
memory seat control button located on the driver's door
or choosing the driver with the DIC. Each remote lock
control transmitter was pre
-programmed to belong to
DRIVER 1 or DRIVER 2. The personalization features
may be programmed differently for each driver.
When you press the unlock symbol on the transmitter,
the DIC will automatically change driver numbers and the
vehicle will recall the personal choice settings that were
last made to correspond to your transmitter, including
your radio and comfort control settings. See ªComfort
Controls, Personalizationº in the Index.
If you unlock the vehicle using your door key instead
of your transmitter, the personal choice settings will
correspond to the previous driver of the vehicle as
identified by a transmitter, a memory seat control or
through the DIC. If this happens and you were not
the last driver of the vehicle, press your correct driver
number on the memory seat controls, press the
unlock symbol on your transmitter or select the
personalization programming mode and choose the
correct driver number.After you have the correct driver number on the display
use the SELECT down arrow button to scroll through
the following messages and feature options:

DOORS LOCK IN GEAR
- YES/NO

DOORS UNLOCK
- YES/NO

ALL DOORS IN PARK
- YES/NO

ALL DOORS AT KEY OFF
- YES/NO

DRIVERS DOOR IN PARK
- YES/NO

DRIVERS DOOR KEY OFF
- YES/NO

PASS WINDOW LOCKOUT
- YES/NO

KEY FOB FLASH LIGHTS
- YES/NO

KEY FOB CHIRP HORN
- YES/NO

DELAY LOCK OF DOORS
- YES/NO

PERIMETER LIGHTS
- YES/NO

EXT LIGHT TIMEOUT
- 25

DISPLAY DRIVER ID
- YES/NO

KEY FOB MEMORY SEAT
- YES/NO

DRIVING POSITION
- YES

EXIT POSITION
- YES

TILT MIRROR REVERSE
- YES/NO

2-87
Window Lockout Personalization
The number of passenger windows locked out by the
window LOCK switch can be programmed through
the DIC.
Press the SELECT right arrow button to toggle between
your choices and change the settings. Press the SELECT
down arrow button to store your changes in memory and
move on to the next selection.
If you select YES for PASS WINDOW LOCKOUT,
all three passenger window switches will be locked out
when the window LOCK switch is on.
If you select NO for PASS WINDOW LOCKOUT,
only the two rear passenger window switches will be
locked out when the window LOCK switch is on.
For more information on this feature, see ªWindow
Lockº in the Index.
Security Feedback
You can program the security feedback feature to
change to the following modes:
Mode 1: No feedback when locking or unlocking
the vehicle.
Mode 2: Parking lamps and the Daytime Running
Lamps will flash twice when unlocking the vehicle
and flash once when locking the vehicle.Mode 3: Horn chirps when all doors are unlocked
(second unlock button press) and when locking
the vehicle.
Mode 4: Parking lamps and the Daytime Running
Lamps will flash twice each time the button with the
unlock symbol is pressed; the horn chirps when all
doors are unlocked. Parking lamps and the exterior
lamps flash once and the horn chirps when locking
the vehicle.
You can change these modes by different selections
of the following DIC displays:

KEY FOB LIGHTS FLASH
- YES/NO

KEY FOB HORN CHIRP
- YES/NO
Press the SELECT right arrow button to toggle between
your choices and change the settings. Press the SELECT
down arrow button to store your changes in memory and
move on to the next selection.
If you would like to program your vehicle to Mode 1,
do the following:
1. Select NO for KEY FOB LIGHTS FLASH.
2. Select NO for KEY FOB HORN CHIRP.

2-88
If you would like to program your vehicle to Mode 2,
do the following:
1. Select YES for KEY FOB LIGHTS FLASH.
2. Select NO for KEY FOB HORN CHIRP.
If you would like to program your vehicle to Mode 3,
do the following:
1. Select NO for KEY FOB LIGHTS FLASH.
2. Select YES for KEY FOB HORN CHIRP.
If you would like to program your vehicle to Mode 4,
do the following:
1. Select YES for KEY FOB LIGHTS FLASH.
2. Select YES for KEY FOB HORN CHIRP.
For more information on this feature, see ªSecurity
Feedbackº in the Index.
Delayed Locking
The delayed locking feature, which delays the actual
locking of the vehicle, can be made active or inactive
through the DIC. When DELAY LOCK OF
DOORS appears on the display, use the SELECT
right arrow button to toggle between YES and NO.When you have made your choice, press the SELECT
down arrow button to record your selection and move on
to the next choice.
For more information on this feature, see ªDelayed
Lockingº in the Index.
Perimeter Lighting Personalization
When the unlock symbol on the transmitter is pressed,
the Daytime Running Lamps, parking lamps and
back
-up lamps will turn on if it is dark enough outside.
You can control activation of this feature by choosing
YES or NO when the PERIMETER LIGHTS choice is
displayed on the DIC. Make your choice by pressing the
SELECT right arrow button and record your choice by
pressing the SELECT down arrow button. You will then
be prompted to choose a TIMEOUT period.
The EXT LIGHTS TIMEOUT feature can be changed
to the desired setting by using the SELECT right arrow
button to toggle from 5 to 30 seconds. Each toggle will
increase the time by 5 seconds. Once the desired timeout
is displayed, press SELECT down arrow to record your
choice and move on to the next personal choice feature.
For more information on this feature, see ªPerimeter
Lightingº in the Index.

3-3

When you press the AUTO-PUSH knob, the lights
under the AUTO
-PUSH and AUTO FAN knobs
will illuminate. Your current comfort setting will be
shown in the digital display.

Set the comfort level you want inside the vehicle by
using the colored buttons located below the climate
control display.

Turn the AUTO
-PUSH knob to select the
manual air delivery mode operation of the climate
control system.
Temperature Buttons
To adjust the comfort level you want maintained inside
the vehicle, use the red and blue buttons located below
the digital display. If you want a warmer comfort level,
push the red button. If you want a cooler comfort level,
push the blue button. Your selected comfort setting will
be shown on the digital display for five seconds, then
the outside temperature will be displayed.Mode Control
Turn the AUTO
-PUSH knob to deliver air through
the floor, panel or windshield outlets. The system will
stay in the selected mode until the AUTO
-PUSH knob
is pressed.
AUTO FAN Knob
This knob controls the fan speed in either an automatic
mode or a manual mode.

Pressing the AUTO FAN knob puts the fan control
in the automatic mode. The AUTO FAN light will
appear below the knob. The fan speed indicators
will not be illuminated when the system is in the
automatic fan control mode.

Turning the AUTO FAN knob selects a manual
fan speed. Turn this knob clockwise to raise the fan
speed. Turn this knob counterclockwise to lower the
fan speed. Turning the AUTO FAN knob overrides
the automatic fan control mode. The fan speed
indicators will be illuminated while in the manual
fan control mode.

3-4
Automatic Operation
Press the AUTO
-PUSH knob when you want the
system to automatically adjust the interior temperature
to your preference. When the system is set for automatic
operation, air will come from the floor, the panel outlets
or the windshield outlets depending on the temperature
inside the vehicle, the outside temperature, the engine
coolant temperature and the sun load. Fan speed will
vary as the system reaches and maintains the comfort
setting you have selected.
To find your comfort setting, start with the system in
automatic mode by pressing the AUTO
-PUSH knob.
Adjust the comfort setting by using the red and blue
buttons located below the digital display until you
reach a setting of 75
F (24
C) on the display. Give the
vehicle about 30 minutes to stabilize and then readjust
the comfort setting if necessary. The display will show
the comfort setting for five seconds and then it will
show the outside temperature.In cold weather, the system will delay turning on the
fan to avoid blowing cold air. The length of the delay
depends on the engine coolant temperature and the
outside temperature. Turning the AUTO FAN knob
will override this delay by turning off the automatic fan
mode and changing the fan speed.
Your automatic electronic climate control system has a
sun sensor located on the top of the instrument panel
that detects direct sunlight. To keep you and your
passengers comfortable, the system may supply cooler
air to the side toward the sun. Be careful not to put
anything over this sun sensor. The automatic electronic
climate control system may not operate correctly if this
sensor is covered.
To change the automatic electronic climate control
display from an English display to a metric display,
push the OFF button located in the Driver Information
Center (DIC) for two seconds. The display in the DIC
will also change from an English to a metric display. To
return to an English display, repeat the above procedure.

3-5
Manual Operation
You may override the automatic airflow distribution by
turning the AUTO
-PUSH knob. After you turn this
knob, the comfort setting will be displayed for five
seconds, then the outside temperature will be displayed.
The fan control will remain in the automatic control
mode unless you turn the AUTO FAN knob to select
a manual fan speed.
PANEL: This setting directs airflow through the
upper air outlets located in the instrument panel.
BI-LEVEL: This setting directs the airflow
through both the panel air outlets and the lower floor
outlets. There is also a small amount of air directed to
the front defroster and the side window defrosters.
FLOOR: This setting directs most of the airflow
to the lower floor outlets with some airflow directed to
the side window defrosters. There is also a small amount
of airflow directed to the front defroster.
DEFOG: This setting directs the majority of
the airflow to the lower floor outlets and the front
defroster. A small amount of airflow is directed to the
side window defroster outlets. This mode can be useful to remove the moisture from the inside of the windshield
when the outside temperature is cold or the humidity is
high. Be sure the A/C indicator light comes on to allow
the air compressor to come on automatically to help
dehumidify the air.
DEF (Defrost): This setting directs the majority
of the airflow to the windshield with some airflow to
the side window defrosters and lower floor outlets.
To increase the fan speed, turn the AUTO FAN knob
clockwise. If defrost is selected from AUTO mode,
your automatic electronic climate control system will
automatically increase the defrost outlet temperature
and fan speed. For maximum front defrost performance
under extreme icing or frosting conditions, increase the
temperature setting to 90
F (33
C) and increase
the fan speed to high.
Even though A/C is not selected, in front defrost
mode the A/C compressor will run automatically
at temperatures over approximately 40
F (4
C) to
improve windshield clearing performance. This
dehumidifies the air to help dry the windshield.
Even though the compressor may be running,
the A/C indicator light will not come on in front
defrost unless you select A/C.

3-6
RECIRC: Press this button to limit the amount
of outside air entering your vehicle. This is helpful when
you are trying to cool the interior of the vehicle quickly
or limit the amount of outside air entering your vehicle
for some other reason. The RECIRC button and the
AUTO
-PUSH knob may be selected at the same time.
The system will remain in RECIRC until the ignition
is turned off, then the system will return back to the
previously selected mode. RECIRC may be selected
in all manual airflow modes except front defrost.
When the weather is cool or damp, operating in
RECIRC for extended periods of time may cause
fogging of the vehicle's windows. To clear the fog,
switch back to outside air by turning off RECIRC,
select either DEFOG or front defrost mode and increase
the fan speed. To avoid refogging of the windows,
minimize your use of RECIRC under these conditions
and turn the A/C on to help dehumidify the air.
A/C: Press this button to turn the air conditioning
compressor on and off. If the system is operating in
the automatic mode, the A/C indicator light will
automatically illuminate. In the auto mode, the
A/C compressor will only operate when the system
determines it is needed.OFF: Turn the AUTO
-PUSH knob to OFF. Turning
the system off will cause the fan to turn off and the
airflow to be directed out the lower floor outlets. The
system will still try to keep the interior of the vehicle
at the previously chosen comfort setting. The outside
temperature will show in the display when the system
is set to OFF.
Air Conditioning
The air conditioner cools and dehumidifies the air for
the inside of the vehicle.
The air conditioning compressor is enabled in all
modes unless the A/C button is in the off position
(the indicator light will not be illuminated). However,
the air conditioning compressor will not operate when
the outside temperature is below 34
F (1
C). When
the air conditioner is on, you may sometimes notice
slight changes in your vehicle's engine speed and power.
This is normal, because the system is designed to cycle
the compressor on and off to keep the desired cooling
and help fuel economy.

3-7
On very hot days, open the windows long enough to
let the hot air out. This reduces the time required to
cool the interior of the vehicle to a comfortable level.
If the system is in the automatic mode (AUTO
-PUSH
knob indicator light is on), during very hot days the
system will automatically go to the RECIRC mode and
the temperature door will initially be at the full cold
position for maximum cooling. You can choose the
extreme comfort setting of 60
F (16
C), but the
system will not cool any faster by choosing the extreme
comfort setting.
Heating
In cold weather, if the automatic mode is selected
(AUTO
-PUSH knob indicator light is on), the system
will automatically direct the airflow out of the lower
floor outlets and the temperature door will initially be
positioned at the full hot position. You can choose the
extreme comfort setting of 90
F (32
C), but the
system will not warm up any faster by selecting the
extreme comfort setting.In cold weather, the system will delay turning on the
fan to avoid blowing cold air. The length of the delay
depends on the engine coolant temperature and the
outside temperature. The fan speed will increase as the
temperature of the engine coolant increases. Turning the
AUTO FAN knob will override this delay by turning
off the automatic fan control mode and changing the
fan speed.
Defogging and Defrosting
On cool, humid days, use the defog setting to keep
the windows clear while also providing heat through the
lower outlets. Turn the AUTO
-PUSH knob clockwise to
DEF to quickly remove fog or ice from the windshield.
For maximum front defrost performance under extreme
icing or frosting conditions, increase the temperature
setting to 90
F (33
C) and increase the fan speed
to high.

3-8 Rear Window Defogger
REAR: Press this
button to warm the
defogger grid on the
rear window. An
indicator light below
the button will glow
while the rear window
defogger is operating.
At speeds above 30 mph (48 km/h), the rear defogger
will stay on until you press the REAR button again.
At speeds below 30 mph (48 km/h), the rear window
defogger will turn off automatically after about
10 minutes of use. If you press it again, the defogger
will operate for about five minutes only. You can also
turn the defogger off by turning off the ignition.
Do not attach a temporary vehicle license across the
defogger grid on the rear window.
When you operate the rear window defogger, the outside
rearview mirrors are also heated to help remove ice and
fog if your vehicle is equipped with heated outside
rearview mirrors. For more information see ªHeated
Outside Rearview Mirrorº in the Index.
NOTICE:
Don't use a razor blade or something else sharp
on the inside of the rear window. If you do, you
could cut or damage the warming grid, and the
repairs wouldn't be covered by your warranty.
Passenger Temperature Control (Option)
With this feature, the right
front seat passenger can
control the comfort setting
for their own zone. To use
this feature, turn the knob
on the passenger's door to
a cooler or warmer setting.
The temperature can be set up to 8
F (4
C) cooler or
warmer than the main setting.

3-14
INFO: If the current station has a message, INFO
will appear on the display. Press this button to see the
message. If the whole message does not appear on the
display, parts of the message will appear every three
seconds until the message is completed. To see the parts
of the message faster than every three seconds, press this
button again. A new group of words will appear on the
display. Once the complete message has been displayed,
INFO will disappear from the display until another new
message is received.
P
-TYPE: This button is used to turn on and off
Program Type (PTY) select. The PTY icon and the light
next to the button will turn on. The last selected PTY
will appear on the display for five seconds. Turn the
P
-TYPE knob to select the PTY you want to listen to.
Press SEEK or SCAN to find radio stations of the PTY
you want to listen to. The last PTY selected will be used
for seek or scan modes. If a station with the selected
PTY is not found, NONE FOUND will appear on the
display. If both P
-TYPE and TRAF are on, the radio
will search for stations with traffic announcements and
the selected PTY.To use the P
-TYPE interrupt feature, press and hold the
P
-TYPE button until you hear a beep on the PTY you
want to interrupt on. An asterisk will appear next to the
PTY name (for example CLASSICAL*). When you are
listening to a cassette or compact disc, the last selected
RDS FM station will interrupt play if that selected PTY
format is broadcast.
PUSHBUTTONS: The six numbered pushbuttons
let you return to your favorite Program Types (PTYs).
These buttons have factory PTY presets. You can set
up to 12 PTYs (six FM1 and six FM2). Just:
1. Press P
-TYPE, if it is not already on.
2. Press AM
-FM to select FM1 or FM2.
3. Turn the SELECT knob to select a PTY.
4. Press and hold one of the six numbered buttons
until you hear a beep. Whenever you press that
numbered button, the PTY you set will return.
5. Repeat the steps for each pushbutton.