mirror OLDSMOBILE AURORA 2002 Owners Manual

1-4 Power Lumbar Control (Option)
If your vehicle has this
option, the power lumbar
controls are located on
the outboard side of each
front seat.
Use the power seat control first to get the proper
position, then continue with the lumbar adjustment.
To reshape the lower seatback, press the lumbar control
forward to increase support and rearward to decrease
support. Press the control up or down to raise or lower
the support mechanism.
Keep in mind that as your seating position changes,
as it may during long trips, so should the position of
your lumbar support. Adjust the seat as needed.
If you have the independent front cushion moved down
as far as it will go, you may feel the lumbar support
higher in your back. Readjust the location of the cushion
until you are comfortable. You may also want to adjust
the seatback for maximum comfort.
Memory Seat and Mirrors (If Equipped)
If your vehicle has this
feature, the controls are
located on the driver's
door panel, and are used to
program and recall memory
settings for the driver's
seating, outside mirror
positions and comfort
controls. See ªComfort
Controlsº in the Index for
more information.
To save your seat and mirror positions into memory,
use the following procedure:
1. First identify the DRIVER # on the Driver
Information Center (DIC) by pressing the memory
button (1 or 2) or by pressing the button with
the unlock symbol on the remote keyless entry
transmitter. See ªDriver Information Center (DIC)º
in the Index.
2. Adjust the driver's seat and lumbar position to a safe
and comfortable driving position. Adjust both outside
mirrors to suit you. See ªMirrorsº in the Index.
ProCarManuals.com

1-5
3. Press and hold the memory button (1 or 2)
corresponding with your DRIVER # displayed on
the DIC for longer than three seconds. You will
hear two beeps confirming that the seat and mirror
positions have been entered into memory.
To set the seat and mirror positions for a second driver,
follow the previous steps, but start by pressing the
button with the unlock symbol on the transmitter that
displays the other DRIVER # on the DIC. Be sure to
use the memory button (1 or 2) which corresponds to
the DRIVER # identified by the second transmitter.
To recall your memory positions, your vehicle must
be in PARK (P). Push and release the memory button
(1 or 2) corresponding to the desired driving position.
The seat and mirrors will move to the position previously
stored for the identified driver. You will hear one beep.
To store the exit position for an easy exit, use the
following procedure:
1. First identify the DRIVER # on the DIC by pressing
the memory button (1 or 2) or by pressing the button
with the unlock symbol on the transmitter.
2. Adjust the driver's seat to the desired exit position.
3. Press and hold the EXIT button for longer than three
seconds. You will hear two beeps confirming that the
seat exit position has been entered into memory.To set the exit position for a second driver, follow the
previous steps, but start by pressing the button with the
unlock symbol on the transmitter that displays the other
DRIVER # on the DIC. Be sure to use the memory
button (1 or 2) which corresponds to the DRIVER #
identified by the other transmitter.
To recall the exit position, your vehicle must be in
PARK (P). Push and release the EXIT button and
the seat will move to the exit position previously stored
for the current identified driver. You will hear one beep.
If an exit position has not been stored for the current
identified driver, the seat will move all the way back.
To stop recall movement of the seat at any time, press
the driver's power seat control located on the outboard
side of the front seat.
Mirror and lumbar positions will not be stored or
recalled for the exit position.
If you would like your stored driving or exit position
to be recalled when unlocking your vehicle with the
transmitter, see ªDIC Personalization Programmingº
in the Index.
ProCarManuals.com

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2
-4 Keys
2
-6 Door Locks
2
-10 Remote Keyless Entry System
2
-15 Trunk
2
-17 Theft
2
-18 Universal Theft-Deterrent
2
-20 PASS-Key
III
2
-22 New Vehicle ªBreak-Inº
2
-22 Ignition Positions
2
-24 Starting Your Engine
2
-25 Engine Coolant Heater (If Equipped)
2
-26 Automatic Transaxle Operation
2
-29 Parking Brake
2
-30 Shifting Into PARK (P)
2
-32 Shifting Out of PARK (P)2
-32 Parking Over Things That Burn
2
-33 Engine Exhaust
2
-34 Tilt Wheel
2
-35 Turn Signal/Multifunction Lever
2
-43 Exterior Lamps
2
-47 Interior Lamps
2
-51 Mirrors
2
-55 Storage Compartments
2
-57 Accessory Power Outlet
2
-58 OnStar
System (If Equipped)
2
-62 Sunroof (Option)
2
-63 HomeLink
Transmitter (If Equipped)
2
-66 The Instrument Panel - Your
Information System
2
-70 Warning Lights, Gages and Indicators
2
-83 Driver Information Center (DIC)
ProCarManuals.com

2-38
For a single wiping cycle, move the lever down to
MIST. Hold it there until the wipers start, then release it.
The wipers will stop after one cycle. If you want more
cycles, hold the lever to MIST longer.
For steady wiping at low speed, move the lever up to the
LO position. For high
-speed wiping, move the lever up
further, to HI. To stop the wipers, move the lever to OFF.
You can set the wiper speed for a long or short delay
between wiper cycles. Move the lever up to the first
detent, INT (Intermittent). Turn the band labeled INT
ADJ (Intermittent Adjustment) down toward the shorter
lines for fewer wiper passes per minute. As you turn the
band toward the longer lines, the wiper cycles per
minute will increase.
Remember that damaged wiper blades may prevent
you from seeing well enough to drive safely. To avoid
damage, be sure to clear ice and snow from the wiper
blades before using them. If they're frozen to the
windshield, carefully loosen or thaw them. If your
blades do become damaged, get new blades or blade
inserts. See ªWindshield Wiper Blade Replacementº
in the Index.
Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice to prevent an overload.
Rainsense
II Wipers (If Equipped)
The moisture sensor is mounted on the interior side of
the windshield below the rearview mirror and is used to
automatically operate the windshield wipers. This
system operates by monitoring the amount of moisture
build
-up on the windshield. Wipes occur as needed to
clear the windshield depending on the driving conditions
and sensitivity setting. In light rain or snow, fewer wipes
will occur. In heavy rain or snow, wipes will occur more
frequently. The system will operate in the delay, low
speed and high speed modes. If the system is left on for
long periods of time, occasional wipes may occur
without any moisture on the windshield. This is normal
and indicates that the Rainsense system is activated.
The Rainsense system is activated by moving the wiper lever
up to the INT position and turning the INT ADJ band to
one of the five sensitivity levels within the delay area. The
bottom INT ADJ position is the lowest sensitivity setting,
level one. This allows more rain or snow to collect on
the windshield between wipes. You can increase the
sensitivity of the system and the frequency of wipes by
turning the INT ADJ band away from you to the higher
sensitivity levels. The top position is the highest sensitivity
setting, level five. A single wipe will occur each time you
turn the INT ADJ band to a higher sensitivity level to
indicate that the sensitivity level has been increased.
ProCarManuals.com

2-50 Rear Reading Lamps
These lamps will come on when you open the doors.
You can also turn them on by pressing the button on the
side of the lamp. Press it again to turn them off.
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle's battery
against drainage from the interior lamps, trunk lamp,
glove box lamp or cigarette lighters. When the ignition
is turned off, the power to these features will
automatically turn off after 10 minutes. Power will be
restored for an additional 10 minutes if any door is
opened, the trunk is opened or the courtesy lamp control
is turned on. To restore power to the cigarette lighters,
the ignition must be turned back to ON.
Battery Load Management
The battery load management feature is designed to
monitor the vehicle's electrical load and determine when
the battery is in a heavy discharge condition. During
times of high electrical loading, the engine may idle at a
higher rpm setting than normal to make sure the battery
charges. High electrical loads may occur when several
of the following are on: headlamps, high beams, fog
lamps, rear window defogger, blower fan, heated seats
and engine cooling fans.
If your vehicle's battery remains in a heavy discharge
condition for a long period of time, the fan, rear
defogger, heated seats and heated mirrors will be
disabled and the DIC will display BATTERY SAVER
ACTIVE. This can happen either under long periods of
idling or low speed driving with high electrical loading,
or in the event of a charging system fault.
ProCarManuals.com

2-51
Mirrors
Electrochromic Day/Night Rearview Mirror
with Compass
Your vehicle has an electrochromic inside rearview
mirror with a compass. Your vehicle's mirror may also
contain OnStar

controls.
(On/Off): This is the on/off button for mirrors
equipped with OnStar controls.
Pressing the MIRROR button (or the on/off button for
mirrors equipped with OnStar controls) located at the
bottom of the mirror, turns the automatic dimming
feature on or off.
The mirror also includes an eight
-point compass
display in the upper right corner of the mirror face.
When on, the compass automatically calibrates as the
vehicle is driven.
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause
the liquid cleaner to enter the mirror housing.Mirror Operation
To turn on the automatic dimming feature, press
MIRROR (or press and hold the on/off button for
about three seconds for mirrors equipped with OnStar
controls). To turn off automatic dimming, press
MIRROR (or press and hold the on/off button for
about three seconds for mirrors equipped with OnStar
controls) again. The green indicator light will be
illuminated when this feature is active. The automatic
dimming feature will be active each time the vehicle
is started.
Compass Operation
Press COMPASS (or the on/off button for mirrors
equipped with OnStar controls) once to turn the
compass on or off.
When the ignition and the compass feature are on, the
compass will show two character boxes for
approximately two seconds. After two seconds, the
mirror will display the compass heading.
ProCarManuals.com

2-52
Compass Calibration
If after two seconds, the display does not show a
compass heading (N for North, for example), there may
be a strong magnetic field interfering with the compass.
Such interference may be caused by a magnetic antenna
mount, magnetic note pad holder or a similar magnetic
item. If the letter C should ever appear in the compass
window, the compass may need calibration.
The mirror can be calibrated in one of two ways:

Drive the vehicle in circles at 5 mph (8 km/h) or less
until the display reads a direction, or

drive the vehicle on your everyday routine.
Mirrors equipped with OnStar controls can be placed in
calibration mode by pressing and holding the on off
button until a C is shown in the compass display.Compass Variance
The mirror is set in zone eight before leaving the
factory. It will be necessary to adjust the compass to
compensate for compass variance if you live outside
zone eight. Under certain circumstances, as during a
long distance cross
-country trip, it will be necessary to
adjust for compass variance. Compass variance is the
difference between earth's magnetic north and true
geographic north. If not adjusted to account for compass
variance, your compass could give false readings.
To adjust for compass variance, do the following:
1. Find your current location and variance zone number
on the following zone map.
2. Press and hold COMPASS (or the on/off button for
mirrors equipped with OnStar controls) until a zone
number appears in the display.
ProCarManuals.com

2-53
3. Once the zone number appears in the display, press
the COMPASS (or the on/off button for mirrors
equipped with OnStar controls) button quickly until
the correct zone number appears in the display.
Stop pressing the button and the mirror will return
to normal operation. If C appears in the compass
window, the compass may need calibration. See
ªCompass Calibrationº explained previously.
Power Remote Control Rearview Mirrors
The controls for the power remote rearview mirrors are
located on the driver's door armrest.
Press the left or right side of the L/R selector switch
located beneath the control pad to choose the left or
right mirror.
ProCarManuals.com

2-54
To adjust the mirror, use one of the four arrows located
on the control pad to move the mirror in the direction
you want it to go. When finished adjusting the mirrors,
leave the L/R selector switch in the center position, to
prevent unwanted mirror movement in case the control
pad is accidentally bumped while driving. Adjust each
outside mirror so that you can see a little of your
vehicle, and the area behind your vehicle.
If your vehicle is equipped with the memory function,
the mirrors and driver's seat position, can be stored into
memory. See ªMemory Seat and Mirrorsº in the Index.
Parallel Park Assist Mirror (If Equipped)
If you have the memory seat and mirrors feature, the
passenger's outside rearview mirror also includes a
tilt
-down feature that operates when the shift lever is
in REVERSE (R). When the vehicle is shifted out of
REVERSE (R), the passenger's mirror will return to
its original position after a five
-second delay. This
delay prevents movement of the mirror if multiple
gear transitions (REVERSE (R) to DRIVE (D)
to REVERSE (R)) occur during a parallel parking
maneuver. This feature can be programmed on or
off through the DIC. See ªDriver Information Centerº
or ªPersonalization Featuresº in the Index for
programming instructions. Vehicles are delivered with
this feature off.
Convex Outside Mirror
Your passenger's side mirror is convex. A convex
mirror's surface is curved so you can see more from
the driver's seat.
CAUTION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you
could hit a vehicle on your right. Check your
inside mirror or glance over your shoulder
before changing lanes.
Heated Outside Rearview Mirror
(If Equipped)
When you operate the rear window defogger, the heated
driver's and passenger's outside rearview mirrors also
warm up to help clear them of ice and snow. See ªRear
Window Defoggerº in the Index.
ProCarManuals.com

2-57
Sun Visors
To block out glare, you can swing down the visors. You
can also remove them from the center mount and swing
them to the side, while the auxiliary visor remains to
block glare from the front.
To extend the visor at the sides, pull out the extension.
Illuminated Visor Vanity Mirrors
When you open the cover to the driver's or passenger's
side visor vanity mirror, the lamps will come on.
Accessory Power Outlet
With accessory power outlets you can plug in auxiliary
electrical equipment such as a cellular telephone or
CB radio.
The accessory power outlet (12
-volt) is located on the
front passenger's side of the vehicle, near the floor on
the console.
Your vehicle may have a small cap that must be pulled
down to access the accessory power outlet. If it does,
when not using the outlet be sure to cover it with the
protective cap.The accessory power outlet will only operate when the
ignition is in ON and for 10 minutes after turning the
ignition off. If you would like the accessory power
outlet to operate regardless of ignition position, and for
extended periods of time, see ªEngine Compartment
Fuse Blockº in the Index or contact your dealer.
NOTICE:
When using accessory power outlets:

Maximum load of any electrical equipment
should not exceed 15 amps.

Be sure to turn off any electrical equipment
when not in use. Leaving electrical
equipment on for extended periods can
drain the battery.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result in
blown vehicle or adapter fuses. If you experience a
problem, see your dealer for additional information
on accessory power outlets.
ProCarManuals.com