reset Oldsmobile Cutlass Supreme 1993 Owner's Manuals

Features & Controls
72
To Resume a Sef Speed
Suppose you set your cruise control at a
desired speed and then you apply the
brake. This, of course, shuts
off the
cruise control. But you don’t need to
reset it. Once you’re going about
25
mph (40 lun/h) or more, you can move
the cruise control switch from
ON to
R/A (which stands for Resume/
Accelerate) for about half
a second.
You’ll go right back up to your chosen
speed and stay there.
A If you hold the switch at R/A
- longer than half a second, the
hicle will keep going faster until
you release the switch or apply the
brake. You could be startled and
even lose control.
So unless you
want to go faster, don’t hold the
switch at
R/A.
To Increase Speed While Using
Cruise Control
There are two ways to go to a higher
speed. Here’s the first:
1. Use the accelerator pedal to get to
the higher speed.
2. Push the button at the end of the
lever, then release the button and the
accelerator pedal.
You’ll now cruise at the higher speed.
Here’s the second way to
go to a higher
speed:
1. Move the cruise switch from ON to
R/A.
Hold it there until you get up to the
speed you want, and then release the
switch.
2. To increase your speed in very small
amounts, move the switch to
R/A for
less than half a second and then
release it. Each time you do this, your
vehicle will go about
1 mph
(1.6 lWh) faster.

9.2
h
Speedometer
(ELECTRONIC CLUSTER)
Press the E/M (English/Metric) button
on the le& side of the instrument cluster
to switch the display between miles per
hour (mph) and kilometers per hotrr
*
Odometer and Trip Odometer
(ELECTRONIC CLUSTER)
Your odometer shows how faryour
vehicle has been driven,
.in either miles
(used in the U.S.) or in kilometers
(used in Canada). YQW trip odometer
tells how far
you have driven since you
last reset it.
To set it to zero, display~the
trip odometer
by pressing the SELECT
button, then press the RESET button.
Both buttons are located on the right
side
of the instrument cluster. Your Oldsmobile
has a tamper resistant
odometer. The odometer
will read
EKROR if someone has ,tampered with
it.
You may wonder what happens if your
vehicle needs
a new odometer installed.
If the new one can be s&to the mileage
total
of the old odometer, then it must
be. But
if it can’t, then it’s set at zero
and a label must be put on the- driver’s
door to show the old mileage reading
when
the llew odometer was installed.

Speedometer (ANALOG CLUSTER)
Your speedometer lets you see your
speed
in both~miles per hour (rnph) and
kilometers per
hour (km/h).
Odometer and Trip Odometer
(ANALOG CLUSTER)
Your odometer shows how far your
vehicle has been driven, in either miles
(used in the U.S.) .or in kilometers
(used
in Canada). Your trip odometer
tells how far you have driven since you
last reset it.
To set it to zero, press the
RESET button located next to the trip
odometer
on the right side of the
instrument panel.
Your Oldsmobile has a tamper resistant
odometer.
If you see silver lines
between the numbers, you’ll know
someone has probably tampered with it
and the numbers may not be true.
You may wonder what happens if your
vehicle needs a new odometer installed.
If the new one can be set to the mileage
total
of the old odometer, then it must
be. But
if it can’t, then-it’s set at zero
and a label must be put
on the driver’s
door to
show the old mileage reading
when the new odometer was installed.
93

brake is fully released, it means you
have a brake problem.
If the light comes
on while driving, pull
off the road and stop carefully. You may
notice that the pedal is harder to push.
Or, the pedal may go closer to the floor.
It may take longer to stop. If the light is
still on, have the vehicle towed for
service. (See the
Index under Towing
Your Oldsrnobile.)
CAUTION
Your brake system may not I
be working properly if the
brake warning light is on. Driving
with the brake warning light on can
lead to an accident. If the light is
still on after you’ve pulled
off the
road and stopped carefully, have
the vehicle towed for service.
Anti-Lock Brake System Warning
Light
(opTloN)
With anti-lock, this light will go on
when you start your engine and it will
stay on for three seconds. That’s
normal. If the light doesn’t come on,
have it fixed
so it will be ready to warn
you if there is a problem.
If the light stays on or comes on when
you’re driving, stop as soon as possible
and turn the key
off. Then start the
engine to reset the system.
If the light
still stays on, or comes
on again while
you’re driving, your Oldsmobile needs
service. Unless the regular brake system
warning light
is also on, you will still
have brakes, but not anti-lock brakes.
If
the regular brake system warning light
99

Comfort Copttrols &Audio Systems
122
AMIFM Stereo Radio with
Cassette Player (CONT.)
2. Press SET. The SET indicator will
appear on the digital screen for five
seconds.
3. While the SET indicator is displayed,
press one of the four pushbuttons.
4. Repeat steps 1-3 for each of four AM
and four FM stations.
Up to three additional stations on each
band may be preset by “pairing”
pushbuttons:
1, Tune in the desired station.
2. Press SET, and within five seconds
press any two adjacent pushbuttons at the same time.
3. The station can be tuned in when the
same two pushbuttons are pressed at
the same time.
To Play a Cassette Tape:
With the power on, insert a tape into
the cassette door. Using tapes that are
longer than
90 minutes (45 minutes on
each side) is not recommended.
When the right indicator arrow is lit,
selections listed on the bottom side of
the cassette are playing. When the left
arrow is lit, selections listed on the top
side of the cassette are playing. To
change sides of the tape, press the
upper control knob
(VOLUME) while
the cassette is playing. The tape player
automatically begins playing the other
side when it reaches the end
of the tape.
Fast Forward Press the button with
the arrow pointing in the same direction
that the tape is playing.
To stop fast
forward, press the
STOP-EJECT
button.
Reverse: Press the button with the
arrow pointing in the opposite direction
that the tape is playing. To stop reverse,
press the
STOP-EJECT button.
STOP-EJECT To stop playing a tape,
fully press this button. The cassette will
be partially ejected, and the radio will
begin playing.

AMIFM Stereo with Cassette
Player and Music Search
The digital display indicates information
on time or radio station frequency, the
AM or FM radio band, whether the
station
is in stereo, and other radio
functions.
POWER: Turns the unit on and off
when the ignition is on.
VOL (Volume): Press the top of the
switch to increase the volume. Press the
bottom of the switch to decrease the
volume. The volume setting will be
displayed. To quickly reduce the volume
to a low level, press the center of the
VOL button.
BASS: Adjusts the bass level.
TREB (Treble): Adjusts the treble
level.
Press the top of each switch to increase
the level, or the bottom to decrease the
level. Press the center of each switch for
preset levels.
Balance Controls
b
Adjusts the lefthight and fronthear
speaker balance to your individual
taste. When you change either
adjustment, the bottom of the digital
screen will display the point
of balance
you have selected. For the normal
setting preset at the factory, press the
left and right or top and bottom button
at the same time.
.s
U
123

Comfort Controls &Audio Systems
I 124
AMIFM Stereo with Cassette
Player
and Music Search (CONT.)
Radio Controls
The band you select will be displayed on
the digital screen. The frequency
of the
station will
also be displayed, and if the
station is in stereo, the
STEREO
indicator will also be displayed.
RCL (Recall): Press to change
between the clock and the radio station
frequency display on the digital screen,
when the radio is on.
AM: Press to select the AM band.
FM: Press to select the FM band.
SEEK A : Press to tune in the next
station higher on the band.
SEEKV: Press to tune in the next
station lower on the band.
SCAN: Press to listen for a few seconds
to the next station on the AM or FM
band; the scan will continue every few
seconds until you press
SCAN again to
stop on a particular station.
TUNE: Press this control to tune in
stations higher or lower on the
AM or
FM radio band.
To Preset Radio Stations:
You can preselect up to 10 radio
stations (five AM and five
FM) and
tune to any
of them by pushing a single
button. Here’s how.
1. Tune to a desired station with the
lower hob.
2. Press SET.
3. Within about five seconds, press one
of the five numbered pushbuttons.
The station you selected will be
automatically tuned whenever you
press this button again.
4. Repeat for up to four more stations
on the same band, and up to five on
the other band.

Comfort Controls &Audio Systems
126
-
..^^L^ I
AMIFM Stereo with Cassette
Player and Graphic Equalizer
The digital display indicates information
on time or radio station frequency, the
AM or FM radio band, whether the
station is in stereo, and other radio
functions.
POWER Turns the unit on and off
when the ignition is on.
VOL (Volume): Press the top of the
switch to increase the volume. Press the
bottom of the switch to decrease the
volume. The volume setting will be
displayed. To quickly reduce the volume
to a low level, press the center of the
VOL button.
Equalizer Controls
Boost the bass, emphasize a voice in a
song, brighten the treble-your
equalizer gives you freedom to adjust
five separate frequencies
of sound to
your individual taste. Move a lever up
to emphasize a frequency, move it clown
to de-emphasize. It’s best to begin with
the levers in the middle position, then
adjust individual levers as you like.
Balance Controls
b
Adjusts the lefthight and front/rear
speaker balance to your individual
taste. When you change either
adjustment, the bottom of the digital
screen will display the point of balance
you have selected. For the normal
setting preset at the factory, press the
center of the balance control.

i, DGlCO-l0C SI )
AM/FM Stereo with Compact Disc
Player
The digital display indicates information
on time or radio station frequency, the
AM or FM radio band, whether the
station
is in stereo, and other radio
functions.
POWER: Press to turn the unit on and
off when the ignition is on.
VOL (Volume): Adjusts the volume
up or down, and the bottom of the
digital screen displays the setting. For a
normal listening level preset at the
factory, press the center of the switch.
TUNE: Press this switch to tune in
higher frequencies and lower
frequencies.
SEEK: Press to tune automatically to
the next station higher on the band.
BAL (Balance): Adjusts the lefthight
and fronthear speaker balance to your
individual taste. When you change
either adjustment, the bottom of the
digital screen
will display the point of
balance you have selected.
For the
normal setting preset at the factory,
press the left and right or front and rear
buttons at the same time.
SCAN: Press to listen for a few
seconds to the next station on the AM
or
FM band; the scan will continue
every few seconds until you press
SCAN again to stop on a particular
station.
RCL (Recall): Press to change
between the clock and the radio station
frequency displayed on the digital
screen.
AM/FM: Press to switch between the
AM and
FM bands. 129

Comfort Controls &Audio Systems
130
AMIFM Stereo with Compact Disc
Player
(CONT.)
To Preset Radio Stations:
The five pushbuttons in the lower right
corner can be used to preset up to ten
radio stations (five
AM and five FM) .
The buttons have other uses when you
are playing a compact disc.
1. Tune the digital display to the station
you want.
2. Press SET. The SET indicator will
appear on the digital screen for five
seconds.
3. While the SET indicator is displayed,
press one
of the five pushbuttons.
4. Repeat steps 1-3 for each of five AM
and five FM stations.
To Play a Compact Disc:
Many of the controls for the radio also
have functions for the compact disc
player, as explained here.
Don’t use mini-discs that are called
singles. They won’t eject. Use only hll-
size compact discs.
1. Press POWER to turn the unit on.
2. Insert a disc part-way into the slot,
with the label side
up. The player will
pull it in. In a few seconds, the disc
should play.
If the disc comes back out:
The disc may be upside down.
The disc may be dirty, scratched or
wet.
There may be too much moisture in
the air (wait about one hour and try
again).
The player may be too hot, or the road
may be too rough
for the disc to play.
While a disc is playing, the CD indicator
is displayed on the digital screen, as is
the clock.
RCL (Recall): Press once 10 see which
track is playing. Press again within five
seconds to see how long your selection
has been playing. The track number
also will be displayed when the volume
is changed or a new track starts to play.
PREV (Previous): Press to play a
track again. If you hold the
PREV
button, the disc will keep backing up to
previous tracks.
NEXT: Press when you want to hear
the next track.
If you hold the NEXT
button, the disc will keep advancing to
other tracks.
REV (Reverse): Press and hold to
rapidly back up to a favorite passage.
Release to resume playing.
FF (Fast Forward): Press and hold to
rapidly advance the disc. Release to
resume playing.
COMP (Compression) : Depressing
this button makes
soft and loud