keyless OLDSMOBILE SILHOUETTE 2003 User Guide

Theft-Deterrent Systems While armed, the doors will not unlock with the power
door lock switch.
Vehicle theft is big business, especially in some cities.
Although your vehicle has a number of theft-deterrent Once
armed, the alarm will go
off if someone tries to
enter the vehicle (without using the remote keyless entry
features, we know that nothing we put on it can make it
transmitter or a key) or turns the ignition to ON. The
impossible to steal. horn will sound and the parking lamps will flash for up to
Content Theft-Deterrent
Your vehicle may have a theft-deterrent alarm system. two minutes.
When
the alarm is armed, the liftgate may be opened
with the remote keyless entry transmitter or with a key.
Arming with the Power Lock Switch
Your alarm system will arm when you use either power
door lock switch to lock the doors while any door or the
liftgate is open and the key is removed from the ignition.
If you would like to turn on power door lock switch arming,
see
Vehicle Personalization on page 2-62.
When the security light flashes quickly the system is
ready to arm with the power door lock switches.
Then the security light will stop flashing and stay on
when you press the rear of the power door lock switch,
and the liftgate are closed and locked, the security light
will begin flashing at a very slow rate to let you know
the system is armed.
tc ]et ;‘cs k~s;~i the syste~ is srm.jnn 3- ‘ Aftnr .‘--. E!! &mrs
A light located on top of your instrument panel (near the
center of the vehicle, next to the windshield) will flash
slowly to let you know that the system has been armed.
2-27

Arming with the Remote Keyless Entry
Transmitter
Your alarm system will arm when you use your remote
keyless entry transmitter
to lock the doors, if the key
is not in the ignition. The security light will turn on to let
you know the system is arming. After all doors and
the liftgate are closed and locked, the security light will
begin flashing at a very slow rate
to let you know
the system is armed.
Arming with Your Key
Your alarm system will arm when you use your key to
lock the doors. The security light will turn on to let
you know the system is arming. After all doors and the
liftgate are closed and locked, the security light will
begin flashing at a very slow rate
to let you know the
system is armed. If you would like your key not
to
arm the system, see Vehicle Personalization on
page 2-62.
Arming Confirmation
If remote unlock confirmation is on, your parking lamps
will flash briefly
to let you know when your alarm system
has disarmed. If you would not like the parking lamps
to
flash, see Vehicle Personalization on page 2-62.
Disarming with the Remote Keyless
Entry Transmitter
Your alarm system will disarm when you use your
remote keyless entry transmitter to unlock the doors.
The security light will stop flashing
to let you know the
system is no longer armed.
Disarming with Your Key
Your alarm system will disarm when you use your key to
unlock the doors. The security light will stop flashing to let
you know the system is no longer armed. If you would like
your key not
to disarm the alarm system, see Vehicle
Personalization on page 2-62.
2-28

Before your vehicle was shipped from the factory,
it was programmed in Mode
3. The mode to which the
vehicle was programmed may have been changed since
it left the factory.
To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Follow the instructions for Entering Programming
Mode on page 2-63.
2. Press LOCK on the power door lock switch.
3. Count the number of chimes you hear.
The number of chimes indicates the vehicle’s
current programmed mode. (If you do not wish to
change the current mode, you can either exit
the programming mode by following the instructions
later in this section or program the next feature
available on your vehicle.)
4. Press LOCK to change the current mode.
5. Press LOCK until you hear the number of chimes
corresponding
to the mode selection you want.
The mode you selected is
now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
Last Door Locking and Lockout
Deterrent
This feature allows you to customize the automatic
locking of the doors when exiting the vehicle.
Programmable Modes
Mode 1: Both Features Off (Doors will always lock
immediately when you press LOCK on the power door
lock switch or the remote keyless entry transmitter.)
Mode
2: Lockout Deterrent Only (If you leave your key
in the ignition with the driver’s door open, you won’t
be able to lock the doors with the power door locks.)
Mode
3: Last Door Closed Locking Only (If the power
door lock switch or the remote keyless entry transmitter
is used to lock the vehicle while any door or the
liftgate is open, you will hear three chimes. The doors
will not lock. Five seconds after the last door is
closed, all doors and the liftgate will lock.)
Mode
4: Both Features On (This combines
Modes
2 and 3.)
2-65

Before your vehicle was shipped from the factory,
it was programmed in Mode
4. The mode to which the
vehicle was programmed may have been changed since
it left the factory. To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Follow the instructions for Entering Programming
Mode on page
2-63.
2. Press UNLOCK on the power door lock switch.
3. Count the number of chimes you hear.
The number of chimes indicates the vehicle’s
current programmed mode.
(If you do not wish to
change the current mode, you can either exit
the programming mode by following the instructions
later in this section or program the next feature
available on your vehicle.)
4. Press UNLOCK to change the current mode.
5. Press UNLOCK until you hear the number of chimes
corresponding to the mode selection you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
Remote Driver Unlock Control
This feature allows you to customize the UNLOCK
button on the remote keyless entry transmitter.
Programmable Modes
Mode 1: Remote All Doors Unlock (When you press
UNLOCK on your remote keyless entry transmitter,
all doors and the liftgate will unlock.)
Mode
2: Remote Driver’s Door Unlock Only
(When you press UNLOCK on your remote keyless
entry transmitter once, the driver’s door will unlock.
When you press UNLOCK on your remote keyless entry
transmitter again within five seconds, all doors and
the liftgate will unlock.)
Before your vehicle was shipped from the factory,
it was programmed in Mode 2. The mode to which the
vehicle was programmed may have been changed since
it left the factory. To determine the mode to which
your vehicle is programmed or to program your vehicle
to
a different mode, do the following:
1. Follow the instructions for Entering Programming
Mode on page
2-63.
2. Press UNLOCK on the remote keyless entry
transmitter.
2-66

3.
4.
5.
Count the number of chimes you hear.
The number of chimes indicates the vehicle's
current programmed mode. (If you do not wish to Remote Lock and Unlock
Confirmation
change the-current mode, you can either exit
the programming mode by following the instructions
later in this section or program the next feature received when locking or unlocking your vehicle with
available on your vehicle.) the remote keyless entry transmitter.
This feature allows
you to customize the feedback
Press UNLOCK to change the current mode.
Programmable Modes
corresponding to the mode selection you want.
Press until You hear the number Of chimes Mode 1: Both Features Off (Remote lock and unlock
confirmation are disabled.)
The mode you selected
is now set. You can either exit
the programming mode by following the instructions
Mode 2: Exterior Lamps Flash Only
later
in this section or program the next feature available 0 When you use the remote keyless entry transmitter
on your vehicle. to lock your vehicle, your parking lamps will flash to
let you know the command has been received.
When you use the remote keyless entry transmitter
to unlock your vehicle or operate your optional
power sliding door(s), your parking lamps will flash
to let you know the command has been received.
2-67

Mode 3: Exterior Lamps Flash and Horn Sounds
When you use the remote keyless entry transmitter
to lock your vehicle, the horn will sound and your
parking lamps will flash to let you know the
command has been received.
When you use the remote keyless entry transmitter
to unlock your vehicle or operate your optional
power sliding door(s), your parking lamps will flash
to let you know the command has been received.
Mode
4: Exterior Lamps Flash and Horn Sounds
(on second LOCK press)
When you use the remote keyless entry transmitter
to lock your vehicle, your parking lamps will flash
to let you know the command has been received.
The horn will sound and your parking lamps
will flash
if you press the LOCK button again
within five seconds.
When you use the remote keyless entry transmitter
to unlock your vehicle or operate your optional
power sliding door(s), your parking lamps will flash
to let you know the command has been received. Before your vehicle
was shipped from the factory,
it was programmed in Mode
4. The mode to which the
vehicle was programmed may have been changed since
it left the factory.
To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Follow the instructions for Entering Programming
2. Press LOCK on the remote keyless entry
3. Count the number of chimes you hear.
Mode on page 2-63.
transmitter.
The number
of chimes indicates the vehicle’s
current programmed mode. (If you
do not wish to
change the current mode, you can either exit
the programming mode by following the instructions
later in this section or program the next feature
available on your vehicle.)
4. Press LOCK to change the current mode.
5. Press LOCK until you hear the number of chimes
corresponding to the mode selection you want.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
2-68

Arming and Disarming the Content
Theft-Deterrent System
To arm or disarm the content theft-deterrent system,
the system must be turned on by using Modes
1, 2 or 4
listed previously.
This feature allows you to customize the arming and
disarming of the content-theft deterrent system.
Programmable Modes
Mode 1: Power Door Lock Switch Arming Off
The system will arm when you lock the doors
with your key or remote keyless entry transmitter.
The key must be removed from the ignition
when you lock the doors or the content
theft-deterrent system will not arm.
The system will disarm when you unlock the doors
with your key or remote keyless entry transmitter.
Mode
2: Remote Keyless Entry Transmitter
Arm/Disarm Only
0 The system will arm when you lock the doors with
your remote keyless entry transmitter. The key
must be removed from the ignition when you lock
the doors or the content theft-deterrent system
will not arm.
0 The system will disarm when you unlock the doors
with your remote keyless entry transmitter. While
this mode provides increased security, it can be
a problem
if your remote keyless entry transmitter
is damaged, lost
or if it fails to operate for any reason
while the content theft-deterrent system is armed.
The content theft-deterrent system must be disarmed
for the engine to run while in Mode
2; your key can
no longer disarm the system.
If your vehicle is equipped with the Onstar@ system,
Onstar@ will not be able to remotely unlock your vehicle
if it has been programmed to Mode 2.
Mode 3: Standard Arming and Disarming
0
0
0
The system will arm when you lock the doors using
either power door lock switch while any door or the
liftgate is open and the key is removed from the
ignition.
The system will arm when you lock the doors with
your key or remote keyless entry transmitter and
the key is removed from the ignition.
The system will disarm when you unlock the doors
with your key or remote keyless entry transmitter.
2-70

Before your vehicle was shipped from the factory,
it was programmed in Mode
1. The mode to which the
vehicle was programmed may have been changed since
it left the factory. To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Follow the instructions for Entering Programming
Mode on page
2-63.
2. Insert your spare key fully into any door key
cylinder and turn it to the unlock position.
This step is necessary to prevent accidental
programming of this feature to Mode
2. Do not
program this feature to Mode
2 without first
reading Mode
2 entirely. The door key cylinder
must remain in the unlock position during
Steps
2 through 4.
3. Press the button with the horn symbol on the
remote keyless entry transmitter.
4. Count the number of chimes you hear.
The number of chimes indicates the vehicle's
curreni programmed mode.
(ii you ao not wish io
change the current mode, you can either exit
the programming mode by following the instructions
later in this section or program the next feature
available on your vehicle.)
5. Press the panic button to change the current mode.
6. Press the panic button until you hear the number
of chimes corresponding to the mode selection
you want.
7. Remove your key from the door key cylinder.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
next in this section or program the next feature available
on your vehicle.
Exiting Programming Mode
To exit programming mode, turn the key from
ACCESSORY to
OFF and put the BCM PRGRM fuse
back into the instrument panel fuse block.
After programming a feature, you can exit the
programming mode at anytime.
Also, if your vehicle
is equipped with the content theft-deterrent system,
remember to arm the svstem before exitinq.
2-71

Entry Lighting
With entry lighting, the interior of your vehicle is
illuminated
so that you can see inside before you enter
your vehicle. The lamps will come on for
40 seconds
if you unlock your door using your key or the remote
keyless entry transmitter and the ignition is in LOCK or
OFF. After 40 seconds have passed, the interior lamps
will slowly fade out. The lamps will turn
off before
the
40 seconds if you:
Lock all the doors using the key,
press LOCK on the power door lock switch, or
press LOCK on the remote keyless entry
transmitter.
When any door is opened, entry lighting is cancelled.
The interior lamps will stay on while any door or liftgate
is open, and slowly fade out when all doors and the
liftgate are closed.
The interior lamps may stay on for up to
25 seconds
after all doors have been closed
if they have not been
locked. See “Delayed Lighting’’ following.
To turn the entry lighting feature
off or on, see Vehicle
Personalization on page
2-62.
Delayed Lighting
The delayed lighting feature will continue to illuminate
the interior for
25 seconds after all doors have been
closed
so that you can find your ignition and buckle your
safety belt at night. Delayed lighting will not occur
while the ignition is in RUN or ACCESSORY. After
25 seconds have passed, the interior lamps will slowly
fade out. The lamps
will fade out before the 25 seconds
have passed
if you:
Turn the ignition to RUN or ACCESSORY,
lock all doors using the remote keyless entry
transmitter, or
lock all the doors using the power door lock switch
or the key.
To turn the delayed lighting feature off or on, see
Vehicle Personalization on page 2-62.
3-1 8

Exit Lighting
With exit lighting, the interior lamps will come on for
about
25 seconds whenever you remove the key from
the ignition.
If you turn the ignition key to RUN or
ACCESSORY, the lamps will fade out. The lamps will
also fade out
if you lock the doors with the power
door lock switch or the remote keyless entry transmitter.
When any door is opened, exit lighting is cancelled.
The interior lamps will stay on while any door or
the liftgate is open, and slowly fade out when all doors
and the liftgate are closed.
The interior lamps may stay on for up to
25 seconds
after all doors have been closed
if they have not been
locked. See “Delayed Lighting’’ earlier in this section.
To turn the exit lighting feature
off or on, see Vehicle
Personalization on page
2-62.
Front Reading Lamps
There are two reading lamps in the overhead console.
To turn either reading lamp on or
off, press the lens
of the lamp. These lamps will come on each time you
override feature. See “Interior Lamps Override’’ earlier
in this section.
cpe!? E!. deer, C!!?!PSS \/e!-! tcrrn nr! the JnterInr !smps
3-1 9