service OPEL 1900 1973 Service Manual

9A-2 1973 OPEL SERVICE MANUALHEATER SYSTEM
- GT
CONTENTS
Subject
DESCRIPTION AND OPERATION:
Flow-ThroughVentilationSystem................................
Heater System Description............................................
HeaterSystemOperation................................................
DIAGNOSIS:
Heater and Defroster........................................................
MAINTENANCE AND ADJUSTMENTS:
Control
CableAdjustment..............................................
MAJOR REPAIR:
Removal
81 Installation Instrument Panel
FreshAirOutlet..............................................................
Removal
& Installation Kick Panel Fresh
AirOutlet..........................................................................
Removal&InstallationBlowerSwitch......................
Removal&InstallationHeater......................................
Removal&InstallationDefrosterOutlet..................
Removal
81InstallationHeaterValve........................
SPECIFICATIONS:
Specifications......................................................................Page No.9A-29A-29A-49A-49A-49A-59A-59A-59A-59A-09A-99A-9
DESCRIPTION AND OPERATION
FLOW-THROUGH VENTILATION SYSTEMA separate ventilation system for direct intake of
outside air is controlled by two plastic fresh air inlet
nozzles in the side kick panels and two lever operated
inlet nozzles located on either end of the instrument
panel assembly.
The air allowed to enter the passenger compartment
will exit through outlets on both sides of the back
glass. See Figure 9A-1.
HEATER SYSTEM DESCRIPTIONThe GT heater system consists of two components
assemblies: (1) heater assembly, and (2) control as-
sembly. The heater assembly consists of the heater
housing and air valves; heater core and blower motor
and fan assembly.Figure
9A-1 GT Air Flow
The flow of air enters the car through the cowl;
passes through the blower fan, through or around the
heater core, past the air inlet door and is then di-
rected to either the floor outlets or defroster outlets
or both depending on the position of the defroster
door.

9A-4 1973 OPEL SERVICE MANUAL
Figure 9A-4 Heater Control
Blower Switch - This switch actuates blower motor
to low or high blower speed.
HEATER SYSTEM OPERATION
To operate heater proceed as follows:
1. Position air inlet, heater-defroster control as
desired.
White arrow head pointing down--air out of heater
outlets. White arrow head pointing up--air out of
defroster outlets.
Between lower and upper position--air to both heater
and defroster outlets.
2. Position temperature control as desired to increase
or decrease temperature of air flow.
3. Position blower switch as desired to operate
blower at low or high speed.
Dlid3NDSlS
HEATER SYSTEM TROUBLE DIAGNOSIS
TROUBLE
Temperature of heated air at outlets too low.
CAUSE AND CORRECTION
Check radiator cap for proper sealing action-- re-
place if necessary.
Check for adequate coolant supply. If level is down,
correct cause of coolant loss and refill radiator.
Inspect hose for kinks--relieve kink or replace hoses.
Check thermostat operation by measuring tempera-
ture of coolant at radiator. Temperature should be
within 5 degrees F. of thermostat rated value (189
degrees F.).
Check that air doors and water temperature control
valye are operating properly.
Check for plugged heater core--backflush heater core
as necessary.
TROUBLE
Inadequate defrosting action.
CAUSE AND COiiRECTlON
Examine heater-defroster door for proper operat-
ions--adjust bowden cable as required so that door is
fully closed in FULL DEFROST position.
Check that air hoses connecting to defroster outlets
are secure.
Check for air leaks around edges of heater air dis-
tributor housing--seal leaks as necessary with body
sealer. Check for body air leaks and seal as necessary
with body sealer.
TROUBLE
Blower inoperative.
CAUSE AND CORRECTION
Check blower fuse--replace if necessary, fuse position
3 - amperage 8.
Check wiring for open circuit--correct as required. Inspect for defective component (i.e., blower switch
or blower motor)--replace or repair as necessary.
MAINTENANCE AND ADJUSTMENTS
CONTROL CABLE ADJUSTMENT
Adjustment of control cables is accomplished by po-
sitioning of the jacket or sheath of the control cable
as held by the clamps on the control assembly and
heater case.
To adjust control cables, loosen clamps and move
cable sheath in or out as required to obtain full travel
of lever or of door or both.

9A-6 1973 OPEL SERVICE MANUAL
b. Remove retaining screw in headlamp lever handle
and remove handle.c. Console cover is held in place by four push button
type studs, unsnap studs by prying cover up and
work cover upwards over shift lever and rubber shift
lever boot.
5. Remove left cover and right plug in instrument
panel cover and through openitigs remove instru-
ment panel attaching screws (points A and B). See
Figures 9A-7 and 9A-8. At this point it will be neces-
sary to lower the steering column, refer to Group 3
for this procedure.6. Remove two multiple wire plug connectors from
steering column harness.
7. Detach speedo cable
8. Remove
dir&ional signal flasher unit. See Figure9A-9.
Figure
9A-9 Directional Flasher Unit
9. Remove 6 instrument cluster retaining screws. See
Figure 9A-10.
Figure
9A-7 Instrument Panel Cover Screw Cover and
Plug LocationsFigure SA-10 Removing Instrument Cluster detaining
SCWWSFigure
SA-8 Location of Hidden Screws10. Grasp instrument cluster and pull straight back,
being careful of wires, etc. See Figure 9A-11.
11. Unscrew heater controls (A) and support bracket
(B). See Figure 9A-12.
12. Disconnect heater and defroster duct
hoses’frominstrument panel. See Figure 9A-13.

9A-8 1973 OPEL SERVICE MANUAL
Installation
1. Install heater blower and case assembly, securing
with one (1) bolt at the top and two (2) nuts from the
bottom. See Figure
9A-15.
2. Install instrument panel padding and connect
heater and defroster duct hoses, making sure hoses
are properly positioned and connected. See Figure
9A-16.
Figure 9A-16 Heater and Defroster Duct Hoses
3. Install support bracket (B) and heater control (A).
See Figure
9A-12.
4. Carefully push cluster back into instrument panel
housing, making sure electrical wires, etc., are not
pinched.
5. Install six (6) cluster retaining screws. See Figure
9A-10.
6. Install directional signal flasher. See Figure
9A- 9.
7. Attach speedometer cable.
8. Attach two (2) multiple wire plug connectors in
steering column harness.
9. Install steering column. Refer to Group 90.
10. Install instrument panel cover and attach
through openings (points A and B). See Figures
9A-7
and 9A-8.
11. Install right and left opening covers. 12. Install the console shift
cover
between the seats
using the following instructions:
a. Install console cover over shift lever and rubber
shift lever boot.
b. Install cover by pushing down until cover snaps into the four (4) push button type studs.
c. Install two (2) screws under ash tray opening and
install ash tray. 13.
In engine compartment, install hood lock control
cable to lock bar using retaining clip. See Figure
9A-
6.
14. Attach return hoses (B) and coolant feed hoses
(A) to heater core. See Figure
9A-5.
15. Attach lower radiator hose and add collected
coolant.
16. Check for proper operation and leaks in system.
REMOVAL AND INSTALLATION DEFROSTER
OUTLET
Removal
1. Remove instrument panel cover assembly. Refer
to Group 1.
2. Remove screws securing outlet to cover assembly.
Installation1. Install defroster outlet, securing with screws.
2. Install instrument panel cover assembly. Refer to
Group 1.
Figure 9A-17 Heater Valve

SA-10 1973 OPEL SERVICE MANUAL
HEATER SYSTEM
OPEL 1900 - MANTA
CONTENTS
Subject
DESCRIPTION AND OPERATION:
Heater System
. . . , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Function of the Heater
and Ventilation System
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DIAGNOSIS:
HeaterSystem
Trouble
Diagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAINTENANCE AND ADJUSTMENTS:
ControlCable
Adjustment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAJOR REPAIR:
Removal&InstallationHeaterHousing,. . . . . . . . . . . . . . . . . . . .Removal
& Installation Defroster Jets. . . . . . . . . . . . . . . . . . . . . .Removal
81 Installation Heater Control Housing . . . .
Removal
& Installation Heater Motor. . . . . . . . . . . . . . . . . . . . . . . .SPECIFICATIONS:
Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page No.
9A-10
9A-11
9A-11
PA-12
PA-12
9A-13
9A-14
9A-15
9A-16
DESCRIPTION AND OPERATIONHEATER SYSTEM
The temperature of the air entering the vehicle is
regulated by the heater valve and the blower. The
distribution of this air is controlled by the heater air
distributor housing under the instrument panel.
Moving the upper control lever from the left towards
the right opens the heater valve. This lever regulates
the flow of coolant through the heater core and
thereby increases or decreases the air temperature
proportionate to its travel. See Figure 9A-30.
Figure 9A-30 Heater Control AssemblyThe connectors for water inlet and outlet are located
on the left side of the heater core, viewed in driving
direction. The coolant flow is shown in the drawing.
See Figure 9A-3 1.
Figure
9A-31 Coolant Flow in Heater Core
Due to the separation of the inflowing and outflow-
ing water in the heater core, an even heating of the

9A-i2 1973 OPEL SERVICE MANUAL
Check that air doors and water temperature control
valve are operating properly.
Check for plugged heater core-backflush heater core
as necessary.TROUBLEInadequate defrosting action.
CAUSE AND CORRECTIONExamine heater-defroster door for proper operation.
Adjust bowden cable so that door is fully closed in
FULL DEFROST position.
Check that air hoses connecting to defroster outlets
are secure.
Check for air leaks around edges of heater air dis-
tributor housing. Seal leaks, as necessary, with bodysea@. Check for body air leaks and seal, as neces-
sary, with body sealer.
TROUBLEBlower inoperative.
CAUSE AND CORRECTIONCheck blower fuse. Replace, if necessary, fuse posi-
tion 4
- amperage 15.
Check wiring for open circuit. Correct, as required.
Inspect for defective component, (i.e., blower switch
or blower motor)
- replace or repair as necessary.
MAINTENANCE AND ADJUSTMENTS
CONTROL CABLE ADJUSTMENTAdjustment of control cables is accomplished by po-
sitioning of the jacket or sheath of the control cable,
as held by the clamps on the control assembly and
heater case or by loosening screws and slidingbowden wire to obtain desired door or water valve
position.
MAJOR REPAIR
REMOVING AND INSTALLING HEATER HOUSING
Removal1. Unscrew hood lock together with ground wire(ground wire only on vehicles with radio interference
suppression). See Figure 9A-33.
Figure 9A-33 Hood Lock Attachments
2. Unscrew heater housing cover.
3. Pull hose of windshield washer system off jet and
take jet out of housing cover.
4. Unscrew bowden control wire from heater valve.
5. Unscrew heater housing from dash panel and pull
it off carefully. See Figure 9A-34.
Figure 9A-34 Heater Housing Attachments
6. Remove water hoses from heater core and pull
heater core out of heater housing. See Figure
9A-35.

9A-14 1973 OPEL SERVICE MANUAL
upper attaching screw through opening for heater
control housing and lower attaching screw below
instrument panel. See Figure 9A.-38.5. On right side, viewed in driving direction, install
air distributor housing attaching screws. See Figure9A-37.
6. Install radio.
7. Install glove compartment.
8. Install bowden control wires to heater valve and
air distributor housing.
9. Install instrument cover.
10. Install heater switch lever.
Figure 9A-38 Upper Attaching Screw
9. Pull defroster outlets downwards and remove out-
lets through glove compartment opening. See Figure9A-39.
REMOVAL AND INSTALLATION OF HEATER
CONTROL HOUSING
Removal1. Remove instrument panel cover
- refer to operat-
ion,
IRemoving and Installing Instrument Housing.
2. Remove two sheet metal screws for control hous-
ing attachment. See Figure 9A-40.
Figure 9A-39 Removing Defroster Jets
Installation
1. Apply sealing compound between air distributor
housing and dash panel.
2. Install defroster outlets, securing with two (2)
clips at the instrument panel. See Figure 9A-39.
3. Install air distributor housing to dash panel,
4. On left side, viewed in driving direction, installFigure 9A-40 Control Housing Attaching Screws
3. In engine compartment, detach bowden control
wire from heater valve. See Figure 9A-41.
4. Detach bowden control wire from air distribution
flap. See Figure 9A-42.
5. Pull wires off blower switch. See Figure 9A- 43.

9A-16 1973 OPEL SERVICE MANUAL
Figure 9A-44 Shroud Cover AttachmentsFigure 9A-46 Heater Motor Attaching Screws
Figure 9A-45 Heater Motor Wires
InstallationFigure 9A-47 Sealing Shroud
1. Install heater motor, attaching with three (3)
screws. See Figure 9A-46.
2. Connect multiple plug on left side of shroud. See
Figure 9A-45.3. Seal shroud cover front and rear contacting areas
with sealing cement. See Figure 9A-47.
4. Install shroud cover, attaching with five (5)
screws.SPECIFICATIONS
EngineRecommended Coolant
..........................................................................Ethylene-Glycol Base
ThermostatOpensAt(Degrees)
F.......................................................................................189Cooling System Capacity (With Heater)
..........................................................................6 Qt.
Blower Motor Type
......................................................................................................12 VDC
Blower Fan Type
..............................................................................................................Blade
Numberof FanBlades
..............................................................................................................7

REFRIGERANT COMPONENTS
ALL MODELS
CONTENTS
Subject
DESCRIPTION AND OPERATION:
FundamentalPrinciplesofRefrigeration..................
Description of Air Conditioning Components
..........DIAGNOSIS:
GeneralInformation..........................................................
Leak Testing
System1........................................................
Functional Testing System............................................
DiagnosisGuide..................................................................
MAINTENANCE AND ADJUSTMENTS:
General Service Information and
Safety Precautions;........................................................
Charging
andDischargingSystem..............................
AddingOiltotheSystem................................................
Flushing the System........................................................
MAJOR REPAIR:
Removal and Installation Compressor
Opel1900.Manta........................................................
GT
........................................................................................
Removal and Installation Condenser
Receiver-Dehydrator
Assembly
- GT.................................................................
Receiver-Dehydrator
.Opel 1900.Manta................GT..................................................
Removal and Installation Evaporator and
Expansion Valve
- Opel 1900.Manta....................
GT......................................................
Disassembly and Reassembly of Clutch Drive
Plate
andShaftSeal....................................................
Disassembly and Reassembly of Pulley Assembly
and Coil and Housing Assembly..............................
Disassembly and
Reaissembly of Internal
Parts of Compressor and Leak Testing
Compressor..............................................................................
SPECIFICATIONS:
Specifications........................................................................Page No.
9B-18
98-33
98-38
98-39
98-39
90-40
98-41
98-41
9B-47
98-48
98-48
98-56
98-62
90-4990-58
98-52
98-59
98-63
98-67
98-69
98-82REFRIGERANT COMPONENTS ALL MODELS
96-17

98.18 1973 OPEL SERVICE MANUAL
DESCRIPTION AND OPERATION
FUNDAMENTAL PRINCIPLES OF REFRIGERATION
We all know what air conditioning does for us, but
very few understand how or why it works. An air
conditioner is functionally very similar to a refrigera-
tor, so let’s take a look at refrigeration. A refrigerator
is a simple mechanism which, surprisingly enough,
works quite a bit like a tea-kettle boiling on a stove.
That may sound far-fetched, but there is more
similarity between the two than most of us would
suspect. In fact, a modern refrigerator can make ice-
cubes and keep food cool and fresh only because a
liquid called the refrigerant boils inside the freezer.
Of codrse everyone knows a boiling tea-kettle is
“hot” and a refrigerator is “cold”. However, this is
where most of us are apt to get confused. We usually
think of “cold” as a definite, positive condition. Ac-
tually though, there is no such thing as “cold”. The
only way we can define it is in a rather negative sort
of way by saying “cold” is simply the lack of heat
just as darkness is the lack of light. We can:t make
things cold directly. All we can do is remove some
of the heat they contain and they will become cold
as a result. And that is the main job of any ice-box
or refrigerator. Both are simply devices for removing
heat.
All substances contain some heat. Theoretically, the
lowest temperature that any substance could obtain
is 459 degrees Fahrenheit below Zero. This may be
called “Cold”, and anything warmer than this con-
tains heat. Since man has never succeeded in getting
all the heat out of an object, we must think about the
transfer of heat from one object to another when
talking about controlling temperatures.
Figure
96-1 Transfer of Heat
Transfer of HeatThe only thing that will attract heat is a colder ob-ject.
:Like water, which always flows down-hill, heat
always flows down a temperature scale
- from a
warm level down to a colder one. When we hold our
hands out toward the fireplace, heat flows from the
hot fire out to our cold hands (Fig.
9B-1). When we
make a snowball, heat always flows from our warm
hands to the colder snow. In an ice-box, the ice al-
ways is colder than the stored food, so heat naturally
is drawn out of the warm food by the colder ice.
Measurement of HeatEveryone thinks he knows how heat is measured.
Thermometers are used in most: homes. Whenever
we speak of temperature from now on, we will mean
Fahrenheit. They can tell how hot a substance is, but
they can’t tell us everything about heat.
Figure
98-2 Applied Temperature Alone is Not the
Sole Measurement of Heat
When we put a tea-kettle on a stove, we expect it to
get hotter and hotter until it finally boils. All during
the process, we can tell exactly how hot the water is
by means of a thermometer (Fig.
9B-2). However,
our thermometer will show us that the flame is just
as hot when we first put the tea-kettle on the stove
as it is when the water finally boils. Why doesn’t the
water boil immediately then? Also, why does it take
longer to boil a quart of water than a cupful? Obvi-
ously temperature isn’t the only measurement of
heat.
Even though heat is intangible, it can be measured by
quantity as well as intensity. It is recognized that
thermometers indicate only the intensity of heat. The
unit for measuring quantity of heat is specified as
that amount necessary to make 1 pound of water 1
degree warmer (Fig.
9B-3). We call this quantity of
heat a British Thermal Unit. Often it is abbreviated
to Btu.
Perhaps we can get a better idea of these two charac-