light PEUGEOT 1007 2008 User Guide

Page 19 of 189

1
22
Low fuel level warning
light
This comes on for a few sec-
onds each time the ignition is
switched on.
When this light fi rst comes on, you
have enough fuel to drive approxi-
mately 30 miles (50 km) (The tank
capacity is approximately 40 litres).
Water in diesel filter
indicator
This comes on for a few sec-
onds each time the ignition is
switched on.
If it comes on, with the engine running,
this indicates that there is a risk of
damage to the injection system.
Consult a PEUGEOT dealer as soon
as possible.
Diesel engine pre-heat
warning light
Wait until the warning light
goes out before starting the
engine.
If the temperature is high enough,
the warning light comes on for less
than one second. You can start the
engine without waiting. Passenger air bag
disarmed warning light
This comes on for a few sec-
onds each time the ignition is
switched on.
If the passenger air bag is disarmed,
the warning light remains on.
Always consult a PEUGEOT dealer if
the warning light fl ashes.
Seat belt not fastened
warning light
When the ignition is switched
on, this warning light comes
on if the driver (and/or a passenger)
has not fastened his seat belt.
Above 12 mph (20 km/h), this warning
light fl ashes for two minutes accom-
panied by an audible signal which be-
comes progressively louder. Once the
two minutes have elapsed, the warning
light remains on until the driver (and/or
passenger) fastens his seat belt.

The driver must ensure that all
passengers fasten and use the
seat belts correctly. Door open warning
light
This comes on if a door, the
bonnet or the boot is still open.
Above 6 mph (10 km/h), this warning
light is accompanied by an audible
signal and a message on the multi-
function display.
"Foot on brake"
warning light
("2 Tronic" gearbox)
When this warning light comes on,
you must put your foot on the brake
(example: when starting the engine).
If you do not put your foot on the
brake, this warning light fl ashes. Front, steering column,
side and curtain air
bags warning light
This comes on for a few seconds each
time the ignition is switched on.
With the engine running, illumination
of this warning light, accompanied by
an audible signal, indicates a fault
in the front, steering column, side or
curtain air bags.
Consult a PEUGEOT dealer.
Emission control
system warning light
This comes on each time the
ignition is switched on and
remains on until the engine is
started.
If it comes on, with the engine run-
ning, it indicates a malfunction of the
emission control system.
Consult a PEUGEOT dealer.

Page 20 of 189

1
23
Lack of oil
If "OIL" fl ashes and the service
warning light comes on, accompanied
by an audible signal and a message
on the multifunction display, this
indicates a lack of oil which could
damage the engine.
If the lack of oil is confi rmed by a
check using the dipstick, it is essential
that the level is topped up.
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 5 seconds after the
service indicator display.
Oil level gauge fault
Check the oil level using the dip-
stick.
If "OIL --" fl ashes, this indicates a
malfunction of the engine oil level
gauge.
Consult a PEUGEOT dealer.
INSTRUMENT PANEL DISPLAY
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator
- total distance recorder (total and trip distances).
The level read on the dipstick
will only be correct if the ve-
hicle is on level ground and
the engine has been off for
more than 15 minutes.
Oil level correct

Note: the trip distance is displayed
for thirty seconds, when the ignition
is switched off, on opening and
closing the driver’s door as well as
on locking the vehicle.
It also displays the "2 Tronic" gear-
box positions and operating modes
selected, as well as the information
relating to the cruise control or speed
limiter when one of these functions is
active.

Page 22 of 189

1
25
Service indicator zero re-set
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder
re-set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears. Total/trip distance recorder
Briefl y pressing the button alternates
between the total and trip distance
displays.
To reset the trip distance recorder to
zero, when it is displayed press the
button until zeros appear.
Lighting rheostat
With the lights on, press the button to
vary the intensity of the lighting of the
instruments and controls. When the
lighting reaches the required bright-
ness, release the button.
After this operation, if you
wish to disconnect the bat-
tery, lock the vehicle and
wait for at least fi ve minutes,
otherwise the zero re-set will not be
registered.

Page 29 of 189


2
32
Vehicle confi guration
Once the "Vehicle confi guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- wiper linked with reverse gear,
- "follow-me-home" lighting. Languages
Once the "Languages" menu has been
selected, you can change the language
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil, Deutsch, English, Espanol).
Display settings
Once the "Display settings" menu has
been selected, you can gain access
to the following settings:
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty). Once you have selected a setting,
press the
"OK" button to change its
value.
Wait for approximately ten sec-
onds without any action to allow the
changed data to be recorded or press
the "ESC" button to cancel.
The display then returns to the nor-
mal display. Units
Once the "Units" menu has been
selected, you can change the units
of the following parameters:
- temperature (°C or °F),
- fuel consumption (l/100, mpg or
km/l).
For safety reasons, it is im-
perative that confi guration of
the multifunction displays by
the driver takes place when
stationary.

Page 30 of 189

2
33
General menu
Press the "MENU" button to gain
access to the general menu, then
press the "  " or "  " buttons to scroll
through the following items:
- radio-CD,
- vehicle confi guration,
- options,
- display settings,
- languages,
- units.
Press the "OK" button to select the
menu required. Vehicle confi guration
Once the "Vehicle confi guration"
menu has been selected, you can
activate or deactivate the following
equipment:
- rear wiper linked with reverse
gear,
- "follow-me-home" lighting.
Presentation
This displays the following informa-
tion, via the RD4 audio equipment
control keypad:
- the time,
- the date,
- the outside temperature (this fl ashes if there is a risk of ice),
- the audio source displays (radio, CD, ...),
- the status of the accesses (doors, boot, ...),
- the warning messages (e.g.: "Anti- pollution system faulty") or infor-
mation messages (e.g.: "Auto
lights on"), displayed temporarily,
can be cleared by pressing the

"ESC" button,
- the trip computer (see corre- sponding section).
MONOCHROME DISPLAY A
Options
Once the "Options" menu has been
selected, you can start diagnostics of
the status of the equipment (active,
not active, faulty).
Radio-CD
With the RD4 audio equipment
switched on, once the "Radio-CD"
menu has been selected, you can
activate or deactivate the functions
linked with the use of the radio (RDS
following, REG mode), the CD or the
CD changer (introscan, random play,
CD repeat).

Page 33 of 189


2
36
Defi ne the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
lowing equipment:
- wiper linked with reverse gear,
- "follow-me-home" lighting and duration.
Example: "Duration of the "follow-me-
home" lighting" Display confi guration
Once this menu has been selected,
you can access the following settings:
- brightness-video setting,
- date and time setting,
- selection of the units.
Once you have selected a setting,
press the navigator.
Turn the navigator to change its value.
Press the navigator to record the
change and move on to the next
setting or press the
"ESC" button to
cancel. Selection of the language
Once this menu has been selected,
you can change the language
used on the display (Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil).
For safety reasons, it is im-
perative that confi guration of
the multifunction displays by
the driver takes place when
stationary.

Page 35 of 189


2
38
Defi ne the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the
following equipment:
- wiper linked with reverse gear,
- "follow-me-home lighting" and duration.
Example: "Duration of follow-me-
home lighting" Display confi guration
Once this menu has been selected,
you can gain access to the following
settings:
- brightness-video setting,
- date and time setting,
- selection of the units.
When you have selected a setting,
press the
"OK" button, then press
the "  " or "  " buttons to change its
value.
Press the "OK" button to record the
change and move on to the next
setting or press the "ESC" button to
cancel. Selection of the language
Once this menu has been selected,
you can change the language
used by the display (Deutsch,
English, Espanol, Français, Italiano,
Nederlands, Portugues, Portugues-
Brasil).
For safety reasons, it is im-
perative that confi guration of
the multifunction displays by
the driver takes place when
stationary.

Page 37 of 189


2
40
Selection of the language
Once the "Selection of the language"
menu has been selected, you gain
access to the following parameters:
- selection of the display, infor-mation and voice commands
language (Français, English,
Italiano, Portugues, Espanol,
Deutsch, Nederlands).
Display confi guration
Once the "Display confi guration"
menu has been selected, you gain
access to the following parameters:
- selection of the palette of colours available for the display,
- setting of the brightness and bril- liance of the display,
- setting of the date and time (12 or 24 hour mode, adjustment
of the minutes on GPS),
- selection of the units (tempera- ture in °Celsius or °Fahrenheit;
consumption in l/100 km or mpg
or km/l).
Sounds
Once the "Sounds" menu has been
selected, you gain access to the
following parameters:
- setting of the voice commands,
- setting of the voice synthesiser (volume of the instructions
and other messages, male or
female),
- activation of the auxiliary input AUX. Defi ne the vehicle parameters
Once the "Defi ne the vehicle param-
eters" menu has been selected, you
can activate or deactivate certain
driving and comfort equipment:
- wiper linked with reverse gear
(refer to the "Visibility" section),
- "follow-me-home" lighting and duration (refer to the "Visibility"
section).
"Configuration" menu

 Press the "MENU" button on
the RT4 GPS audio/telephone
to gain access to the general
menu .

 Turn the dial to select the

"Confi guration" menu, then
press it to confi rm.
Once this menu has been selected,
you can gain access to the following
functions:

Page 38 of 189

2
41

 Select the line "Duration of the
"follow-me-home" lighting" then
confi rm.
Example: setting the duration of the
"follow-me-home" lighting.

 Turn the dial to select the "Lighting
confi guration" menu, then press it
to confi rm.

 Select the duration then press
the dial.

 Turn the dial to set the value
required (15, 30 or 60 seconds),
then press the dial.


Select the "OK" box, then confi rm.
The RT4 GPS audio/tele-
phone must reinitialise and
restart in order to change
the voice used by the voice
synthesiser (male or female)
or the language used by the
system.
For safety reasons, it is im-
perative that confi guration of
the multifunction displays by
the driver takes place when
stationary.

Page 41 of 189

3
44
Turn the control from blue
(cold) to red (hot) to adjust
the temperature to your
requirements.
HEATING/VENTILATION
The heating and ventilation can only
operate when the engine is running.
1. Temperature adjustment
Version with button and indicator light Version with manual control
2. Air fl ow adjustment Turn the control from
position 1 to position 4 to
obtain a fl ow of air suffi cient
to ensure your comfort.
To maintain a certain level of comfort
in the passenger compartment, avoid
position 0 as much as possible.
However, in position 0 , a slight fl ow
of air, due to the movement of the
vehicle, can still be felt.

Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 ... 70 next >