display PEUGEOT 2008 2013 Owner's Manual

78
Driving








Starting-stopping the engine With a manual gearbox, put the gear lever in neutral.
With an electronic gearbox , put the gear lever on N
.
With an automatic gearbox , put the gear lever on P
or N.
)Inser t the key in the ignition switch.
The system recognises the star ting code. )Turn the key fully towards the dashboard toposition 3 (Starting).)When the engine starts, release the key.
Starting the engine

A heavy object (key fob...), attached tothe key and weighing down on its shaft in the ignition switch, could cause amalfunction.
Key left in the "Ignition on"position
On opening the driver's door, an aler t message is displayed, accompanied by an audible signal, to remind you that the key isstill in the ignition switch at position 1 (Stop).
)
Immobilise the vehicle.)
Turn the key fully towards you to
position 1 (Stop).) Remove the key from the ignition switch.


Switching the engine off

If the key has been left in the ignition
switch at position 2 (Ignition on),the ignition will be switched off automatically after one hour.
To switch the ignition back on, turn the key to position 1 (Stop)
, then back toposition 2 (Ignition on).


Free wheeling

For safety reasons, do not free wheel.
When free wheeling, some vehicle functions will no longer be active.

83
4
Driving

Never select neutral N
while the vehicleis moving. Only engage reverse gear Rwhen thevehicle is immobilised, with your foot on the brake pedal. In all cases, you must apply the parkingbrake to immobilise the vehicle.



"Au t o s equential" mode

In the automated mode, you can resumecontrol temporarily at any time using thesteering mounted control paddles.
The use of these paddles permits manual
selection of the gears in situations which
require a more rapid change-down than in
the automated mode (arrival at a roundabout,
leaving a car park with a steep gradient,
over taking...).
The gearbox engages the required gear if
the engine speed permits. AUTO
remains
displayed on the instrument panel.
After a few moments, the gearbox resumes
automatic control of the gears.
Stopping the vehicle
Before switching off the engine, you canchange to position N to be in neutral.
In this case,
you must apply the parking brake to immobilise the vehicle.
AUTO
and -
appear in the instrument panel.-


Operating fault

With the ignition on, if this warning
lamp comes on and AUTOflashes, accompanied by an
audible signal and a message in the screen,
this indicates a gearbox fault.
Have it checked by a PEUGEOT dealer or a qualified workshop.


For best acceleration, when over taking another vehicle for example, press the accelerator pedal firmly to pass the
point of resistance.

)
Select position N.)
Press the brake pedal.
)
Wait approximately 30 seconds until N
or agear appears in the instrument panel.)
Release the brake pedal.
The gearbox is operational again.
Reinitialisation
Following disconnection of the battery, the
gearbox must be reinitialised.
) Switch on the ignition.

85
4
Driving

Engagement of reverse gear isaccompanied by an audible signal.
Nflashes in the instrument panel,accompanied by an audible signaland a message in the instrument panel screen, if the gear lever is not inposition N
on starting.


For optimum acceleration, for example when over taking another vehicle, pressthe accelerator pedal firmly past the point of resistance.



Display in the instrument panelMoving off
Automated mode


Gear lever positions
N.
Neutral
R.Reverse1, 2, 3, 4, 5, 6.Gears in manual mode
AUTO. This comes on when the automatedmode is selected. It switches off on changing to manual mode.
)
Place your foot on the brakewhen
this warning lamp is flashing (for example, when star ting the engine).

)
Select position N.)
Press the brake pedal down fully. )
Start the engine.
Nappears in the instrument panelscreen.
)
Select automated mode (position A
), Amanual mode (position M ), or reverse(position R).R)
Release the parking brake.)
Ta k e your foot off the brake pedal, thenaccelerate.
AUTOand 1, 1
or R
appears in the instrument panel screen.
)
After star ting the vehicle, select position Afor enter automated mode.
AUTO
and the gear engaged appear
in the instrument
panel screen.
The
gearbox is then operating in auto-active
mode, without any action on the par t of the driver. It continuously selects the most suitablegear, depending on the:


- style of driving,

- profile of the road. Foot on brakeflashes on theinstrument panel, accompanied by an audible signal and a message in the instrument panel screen, if the brake pedal is not pressed on starting.

86
Driving

At very low speed, if reverse gear is requested, this will only be takeninto account when the vehicle is immobilised. A warning lamp appears in the instrument panel screen.
Manual gear changing
Manual mode

On sharp acceleration, the gearbox willnot change up unless the driver acts onthe gear lever or the steering mounted paddles.
Never select neutral N
while the vehicleis moving.
Only engage reverse gear Rwhen thevehicle is immobilised with the brakepedal pressed. This selective
gear change mode enables you
to over take, for example, while still remaining in automatic mode.)Operate the +or - steering mounted controlpaddle.
The gearbox engages the gear requested if theengine speed permits. AUTOis still displayed
in the instrument panel.

After a few moments without any action on
the controls, the gearbox resumes automatic control of the gears.
) When the vehicle has moved off, select
pos
ition M to change to manual mode.


- Pull the lever towards the +sign to change up a gear.

- Push the lever towards the -sign to change down a gear.
The
gears engaged appear successively in the instrument panel screen.
The
gear change requests are only carried out
if the engine speed permits.
It is not necessary to release the accelerator
during gear changes.
When braking or slowing down, the gearbox
changes down automatically to permit
acceleration in the correct gear.

88
Driving
Four-speed automatic gearbox which offers a choice between the comfor t of fully automatic operation, enhanced by spor t and snow
programmes, or manual gear changing.
There are therefore four driving modes:-automatic
operation for electronic management of the gears by the gearbox,
-
sportprogramme for a more dynamic style
of driving,

- snowprogramme to improve driving when
traction is poor,

-
sequentialoperation for manual changing
of the gears by the driver.















Automatic gearbox
1.
Gear lever.2.
Button "S"(sport)
.
3.Button "7"(snow).



Gear selection gateGear lever
P.Park.
- Immobilisation of the vehicle, parking brakeon or off.
- Starting the engine.
R. Reverse.
- Reversing manoeuvres, vehicle stationary, engine at idle.N.Neutral.
- Immobilisation of the vehicle, parking brakeon.
- Star ting the engine.D.
Automatic operation. M + / -. Manual operation with sequential changing of the four gears.)Push for wards to change up through the
gears.or )Pull backwards to change down through
the gears.



Displays in the instrument panel

When you move the lever in the gate to select
a position, the corresponding indicator is
displayed in the instrument panel. P. Park R.ReverseN.
NeutralD.Drive (Automatic driving) S.Sport
programme 7.Snowprogramme
1 2 3 4. Gears engaged during manual
operation
-. Invalid value during manual operation


Foot on brake
)
Press the brake pedal when this
indicator lamp is displayed in the
instrument panel
(e.g.: starting
the engine).

89
4
Driving
)Apply the parking brake. )Select position P or N
.
)Star t the engine.
If this procedure is not followed, there is an
audible si
gnal, accompanied by the display of
an warning message.)With the engine running, press the brake pedal. )Release the parking brake. )Select position R, Dor M.)Gradually release the brake pedal.
The vehicle moves off immediately.


Moving off


When the engine is running at idle, with the brakes released, if position R, D
or M
is selected, the vehicle moves evenwithout the accelerator being pressed.
When the engine is running, never leave children in the vehicle without supervision. When carrying out maintenance with the engine running, apply the parkingbrake and select position P
.
P


If position N
is selected inadver tently while driving, allow the engine toreturn to idle then select position D
toaccelerate.
Never select position N
while the vehicle is moving.Never select positions P
or Runless thevehicle is completely stationary.

Automatic operation
)
Select position Dfor automaticchanging
of the four gears.The gearbox then operates in auto-adaptivemode, without any inter vention on the par t
of the driver. It continuously selects the most
suitable gear according to the style of driving,
the profile of the road and the load in the
v
ehicle.
For maximum acceleration without touching the gear lever, press the accelerator pedal downfully (kick down). The gearbox changes downautomatically or maintains the gear selecteduntil the maximum engine speed is reached.On braking, the gearbox changes downautomatically to provide efficient engine
braking.
If you release the accelerator sharply, thegearbox will not change to a higher gear for
safety reasons.

Sport and snow programmes


Sport programme "S"
)
Press button "S", after star ting the engine.
The
gearbox automatically favours a dynamic style of driving.
S
appears in the instrument panel.


Snow programme " 7
"
)
Press button "7
", after star ting the engine.
The gearbox adapts to driving on slipperyroads.
This programme improves star ting and drive
when traction is poor.
7 appears in the instrument panel.



Return to automatic
o
peration
) At any time, press the button selectedagain to quit the programme engaged and
return to auto-adaptive mode. These two special programmes supplement the
automatic operation in ver
y specific conditions of use.

90
Driving
Manual operation
)Select position M for sequentialchanging
o
f the four gears.)Push the lever towards the + sign tochange up a gear. )Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to another if the vehicle speed and engine speedpermit; otherwise, the gearbox will operate
temporarily in automatic mode.
D disappears and the gears engaged appear in succession in the
instrument panel.

Invalid value during manual operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can engage
position Por N
to place the gearbox in neutral.
In both cases, apply the parking brake to
immobilise the vehicle.

Operating fault
When the ignition is on, thelighting of this warning lamp,
accompanied by an audible signal and a
message in the multifunction screen, indicates
a gearbox fault.
In this case, the gearbox switches to back-up mode and is locked in 3rd gear. You may feel
a substantial knock when changing from Pto Rand from N to R
. This will not cause any damage to the gearbox.
Do not exceed 60 mph (10 0 km/h), local speed
restrictions permitting.

Contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
I
f the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D(automatic) to position M (manual) at any time.
When the vehicle is stationary or movingvery slowly, the gearbox selects gear M1automatically. The spor t and snow programmes do not
operate in manual mode.

There is a risk of damage to thegearbox:


- if you press the accelerator and brake pedals at the same time,

- if you force the movement of the gear lever from the Pposition toanother position when the battery isflat.
To reduce fuel consumption when at
a prolonged standstill with the enginerunning (traffic jam...), put the gear lever in the Nposition and apply the parkingbrake.

If the lever is not in position P
, when the Pdriver's door is opened or approximately 45 seconds after the ignition is switchedoff, a warning message appears in the screen.)Return the lever to position P; the
message disappears.

96
Driving





Speed limiter
System which prevents the vehicle fromexceeding the speed programmed by the driver.
When the programmed speed limit is reached,
pressing the accelerator pedal in the normalmanner no longer has any effect.
The speed limiter is switched onmanually: the programmed speed must be at least 20 mph (30 km/h).
The speed limiter is switched off
by manual foperation of the control.
The programmed speed can be exceeded
temporarily by pressing the accelerator firmly.
To return to the programmed speed, simply slow down to a speed below the programmed speed.

The speed limiter cannot, in any circumstances,replace the need to respect speed limits, nor can it replace the need for vigilance and responsibility on the par t of the driver.

The controls of this system are grouped
together on stalk A.1.Speed limiter mode selection thumb wheel.2. Value decrease button. 3.
Value increase button. 4.Speed limiter on / off button.


Steering mounted controls

The programmed information is grouped
together in the instrument panel screen.
5. Speed limiter on / off indication.
6.Speed limiter mode selection indication. 7. Programmed speed value. 8.Selection of a memorised speed setting.
(see "Memorising speeds")

Displays in the instrument panel
The programmed speed remains in the memorywhen the ignition is switched off.

97
4
Driving
) Turn thumb wheel 1to the "LIMIT"position: the speed limiter mode
i
s selected but is not switched on(PAUSE).
You do not have to switch the speed limiter
on in order to set the speed.



Programming
Pressing the accelerator pedal to exceed the programmed speed will not have
any effect unless you press the pedal firmlypast the ypoint of resistance.e The speed limiter is deactivated temporarily and the programmed speed,
which is still displayed, flashes.
Returning to the programmed speed, by means of intentional or unintentional
deceleration of the vehicle, automatically cancels the flashing of theprogrammed speed.

Leaving limiter mode
)
Turn thumb wheel 1to the "0"
position:
the speed limiter mode is deselected. The
displa
y returns to the distance recorder.
On a steep descent or in the event of sharp acceleration, the speed limiter willnot be able to prevent the vehicle from exceeding the programmed speed.
To avoid any risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- do not fit one mat on top of another.

In the event o
f a speed limiter fault, the speed
is cleared resulting in flashing of the dashes.
Have it checked by a PEUGEOT dealer or a qualified workshop.


Operating fault
)Set the speed value by pressing button 2or 3(e.g.: 55 mph(90 km/h)).
You can then change the programmed speed using buttons 2 and 3:


- by + or - 1 mph (km/h) = shor t press,

- by + or - 5 mph (km/h) = long press,

- in steps of + or - 5 mph (km/h) = maintained press.




Exceeding the programmed speed
)Switch the speed limiter back on by pressing button 4
again.


)Switch the speed limiter on by pressing button 4 . )Switch the speed limiter off by pressing button 4
: the display confirms that it has been switched off (PAUS E).

98
Driving





Cruise control
System which automatically maintains thespeed of the vehicle at the value programmed
by the driver, without any action on the accelerator pedal.
The cruise control is switched on
manually: itrequires a minimum vehicle speed of 25 mph(40 km/h), as well as the engagement of:
-
fourth gear on a manual gearbox,
- second gear on an electronic or automaticgearbox, in sequential mode,
- position A
on an electronic gearbox or position D
on an automatic gearbox.
Th
e cruise control is switched offmanuallyfor by pressing the brake or clutch pedal or on
triggering of the electronic stability system for safety reasons.
It is possible to exceed the programmed speed
temporarily by pressing the accelerator pedal. To return to the programmed speed, simply release the accelerator pedal. Switching off the ignition cancels any programmed speed value. The controls of this s
ystem are grouped
together on stalk A .
1.Cruise control mode selection thumb wheel.2. Value decrease button. 3.
Value increase button. 4.Cruise control off/resume button.


Steering mounted controls
The cruise control cannot, in any circumstances, replace the need to respect speed limits,nor can it replace the need for vigilance andresponsibility on the par t of the driver.


The programmed information is grouped
together in the instrument panel screen.
5. Cruise control off/resume indication.
6.Cruise control mode selection indication.7. Programmed speed value. 8.Selecting a memorised speed setting.
(see "Memorising speeds")

Displays in the instrument panel