display PEUGEOT 207 2008 Owner's Guide

i
ACCESS
Starting the vehicle

 Insert the key in the ignition switch.
The system recognises the starting code.

 Turn the key fully towards the fascia
to position 3 (Starting) .

 When the engine starts, release the
key.
Switching the vehicle off

 Immobilise the vehicle.


Turn the key fully towards you to position 1
(Stop) .


Remove the key from the ignition switch.
Remote control problem
Following disconnection of the vehicle
battery, replacement of the remote control
battery or in the event of a remote control
malfunction, you can no longer unlock,
lock or locate your vehicle.

 First of all, use the key in the lock to
unlock or lock your vehicle.

 Then, reinitialise the remote control.
If the problem persists, contact a
PEUGEOT dealer as soon as possible. Changing the battery
Battery ref.: CR1620/3 volts.
Reinitialisation

 Switch off the ignition.

 Turn the key to position 2 (Ignition) .

 Press the closed padlock immediately
for a few seconds.

 Switch off the ignition and remove
the key from the ignition switch.
The remote control is fully operational
again.
 Unclip the casing using a coin at the
notch.

 Slide the fl at battery out of its location.

 Slide the new battery into its location
observing the original direction.

 Clip the casing.

 Reinitialise the remote control. This replacement battery is avail-
able from PEUGEOT dealers.
If the battery is fl at, you are in-
formed by lighting of this warning
light, an audible signal and a mes-
sage on the multifunction display.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park:

 press the closed padlock, the courtesy
lights come on and the direction indi-
cators fl ash for a few seconds.
Key reminder
If the key is left in the ignition switch,
an audible signal sounds when the
driver’s door is opened.

!
ACCESS
74
DOORS

 After unlocking the vehicle using the
remote control or the key, pull the
door handle. From inside

 Pull the front door control to open
the door; this unlocks the vehicle
completely.

 Pull the rear door control to open the
door; this unlocks the door concerned
only.
The interior door controls do not
operate when the vehicle is dead-
locked. Closing
If a door is not closed correctly:
- when the engine is running,
this warning light comes on,
accompanied by a message
on the multifunction display
for a few seconds,
- when the vehicle is moving (speed
above 6 mph (10 km/h)), this warn-
ing light comes on, accompanied by
an audible signal and a message on
the multifunction display for a few
seconds.
Opening
From outside

i
!i
75
If the vehicle is locked or dead-
locked from the outside, the red
indicator light fl ashes and button A
is inactive.

 In this case, use the remote
control or the key to unlock the
vehicle.
If one of the doors or the boot or
rear screen is open, the automatic
central locking does not take place.
Manual centralised control
System which provides full manual
locking or unlocking of the doors from
the inside.
Locking

 Press button A to lock the vehicle.
The red indicator light on the button
comes on. Automatic centralised
control
System which provides full automatic
locking or unlocking of the doors, boot
and rear screen while driving.

You can activate or deactivate this function. Activation

 Press button A for more than two
seconds.
A confi rmation message appears on the
multifunction display.
Unlocking

 Above 6 mph (10 km/h), press button

A to unlock the doors, the boot and
the rear screen temporarily.
If one of the doors is open, the central
locking from the inside does not take
place.
Unlocking

 Press button A again to unlock the
vehicle.
The red indicator light on the button
switches off. Locking
When the speed exceeds 6 mph
(10 km/h), the doors, the boot and the
rear screen lock automatically.
Deactivation

 Press button A again for more than
two seconds.
A confi rmation message appears on the
multifunction display.

ACCESS
Emergency control
System which locks or unlocks the doors
mechanically in the event of a malfunction
of the central locking.

 Insert the key in the lock, located on
the edge of the door, then turn it one
eighth of a turn .
Locking the driver’s door

 Insert the key in the lock, then turn it
to the right.
Unlocking the driver’s door

 Insert the key in the lock, then turn it
to the left.
Locking the front and rear
passenger doors
Unlocking the front and rear
passenger doors

 Pull the interior door opening control. -
when the engine is running,
this warning light comes on,
accompanied by a message
on the multifunction display
for a few seconds,
- when the vehicle is moving (speed
above 6 mph (10 km/h)), this warn-
ing light comes on, accompanied by
an audible signal and a message on
the multifunction display for a few
seconds. Tailgate release
System for mechanical unlocking of the
boot in the event of a central locking
malfunction.
Unlocking

 Fold back the rear seats to gain
access to the lock from inside the
boot.

 Insert a small screwdriver into hole

A of the lock to unlock the tailgate.
Opening

 After unlocking the vehicle using the
remote control or the key, pull the
handle and raise the tailgate. BOOT (SALOON)
Closing
If the tailgate is not closed correctly:

ACCESS
Emergency control
System which locks or unlocks the doors
mechanically in the event of a malfunction
of the central locking.

 Insert the key in the lock, located on
the edge of the door, then turn it one
eighth of a turn .
Locking the driver’s door

 Insert the key in the lock, then turn it
to the right.
Unlocking the driver’s door

 Insert the key in the lock, then turn it
to the left.
Locking the front and rear
passenger doors
Unlocking the front and rear
passenger doors

 Pull the interior door opening control. -
when the engine is running,
this warning light comes on,
accompanied by a message
on the multifunction display
for a few seconds,
- when the vehicle is moving (speed
above 6 mph (10 km/h)), this warn-
ing light comes on, accompanied by
an audible signal and a message on
the multifunction display for a few
seconds. Tailgate release
System for mechanical unlocking of the
boot in the event of a central locking
malfunction.
Unlocking

 Fold back the rear seats to gain
access to the lock from inside the
boot.

 Insert a small screwdriver into hole

A of the lock to unlock the tailgate.
Opening

 After unlocking the vehicle using the
remote control or the key, pull the
handle and raise the tailgate. BOOT (SALOON)
Closing
If the tailgate is not closed correctly:

i
i
77
Opening

 After unlocking the vehicle using the
remote control or the key, with the
rear screen closed, pull on the handle

A and raise the tailgate.
- when the engine is running,
this warning light comes on,
accompanied by a message
on the multifunction display
for a few seconds,
- when the vehicle is moving (speed
above 6 mph (10 km/h)), this warn-
ing light comes on, accompanied by
an audible signal and a message on
the multifunction display for a few
seconds.
Closing

 Lower the tailgate using the interior
grab handle.
If the tailgate is not closed correctly:
REAR SCREEN (SW)
Opening

 After unlocking the vehicle using the
remote control or the key, with the
boot closed, press the control B and
raise the rear screen using the base

C of the wiper arm.
The boot and the rear screen cannot
both be open at the same time.

If the rear wiper is in a wiping position,
the rear screen will not open until the
end of the cycle.
Closing

 Close the rear screen by pressing at
the centre of the glass.
If the rear screen is not closed correctly:
- when the engine is running,
this warning light comes on,
accompanied by a message
on the multifunction display
for a few seconds,
- when the vehicle is moving (speed
above 6 mph (10 km/h)), this warn-
ing light comes on, accompanied by
an audible signal and a message on
the multifunction display for a few
seconds.
BOOT (SW)
If the rear screen is open, the central
locking does not take place.

81
LIGHTING CONTROLS
System for selection and control of the
various front and rear lights providing
the vehicle’s lighting. Manual controls
The lighting commands are made directly
by the driver by means of ring
A and
lever B .
lights off,
side lights only, dipped or main beam
headlamps,

B. lever for inversion of the lights by
pulling: dipped headlamps/main
beam headlamps.
In the lights off and side lights modes,
the driver can switch on the main beam
headlamps directly ("headlamp fl ash")
for as long as he pulls the lever.
Displays

The corresponding indicator light comes on on
the instrument panel to confi rm the selective
switching on of the lighting selected.
Main lighting
The vehicle’s various front and rear lights
are designed to adapt the driver’s visi-
bility gradually in relation to the climatic
conditions:
- side lights, to be seen,
- dipped headlamps to see without dazzling other drivers,
-
main beam headlamps for good visibility
when the road is clear.
Additional lighting
Other lights are installed to respond to
particular driving conditions:
- rear fog lamps to be seen from a distance,
-
front fog lamps for even better visibility,
- directional headlamps for improved visibility around bends.
Programmes
Various automatic lighting control
modes are also available according to
the following options:
- "follow-me-home" lighting,
- automatic lighting,
- static directional lighting.
A. main lighting mode selection ring,
with:
Model without AUTO lighting
Model with AUTO lighting automatic lighting.

!
83
In fog or snow, the brightness
sensor may detect suffi cient light.
Therefore, the lights will not come
on automatically.
Do not cover the brightness sensor,
coupled with the rain sensor and
located in the centre of the wind-
screen behind the interior mirror;
the associated functions would no
longer be controlled.
Coupling with the "Follow-me-home"
lighting
Association with the automatic lighting
provides the "follow-me-home" lighting
with the following additional options:
- selection of the duration of main-
taining of the lighting for 15, 30 or
60 seconds in the vehicle param-
eters on the multifunction display
confi guration menu,
- automatic activation of "follow-me- home" lighting when automatic lighting
is in operation.
Automatic lighting
The side lights and dipped headlamps
are switched on automatically, without
any action on the part of the driver, when
a low level of external light is detected
(sensor behind the interior mirror) or when
the windscreen wipers are switched on.
As soon as the brightness returns to a
suffi cient level or the windscreen wipers
are switched off, the lights are switched
off automatically.
"Follow-me-home" lighting
The dipped headlamps remain on tem-
porarily, after switching off the vehicle’s
ignition, to make the driver’s exit easier
in poor light.
Activation

 With the ignition off, activate a
"headlamp fl ash" using lever B .

 A second "headlamp fl ash" switches
the function off again.
Switching off
The "follow-me-home" lighting is
switched off automatically following the
door locking command, after a given
time. Activation

 Turn ring A to the "
AUTO
" position.
The automatic lighting is accompanied
by a message on the multifunction dis-
play. Operating fault
In the event of a malfunction of
the brightness sensor, the lights
come on accompanied by the
service warning light, an audible
signal and a message on the multifunction
display.
Have it checked by a PEUGEOT dealer.
Daytime lights *
On vehicles fi tted with daytime lights,
the dipped headlamps come on when
the vehicle is started.
This indicator light comes on
on the instrument panel.
The instruments and controls (instru-
ment panel, multifunction display, air
conditioning control panel, ...) are not
lit, unless the automatic switching on of
the lights mode is activated or the lights
are switched on manually.
Deactivation

 Turn ring A to a position other than
" AUTO " . Deactivation is accompanied
by a message on the multifunction dis-
play.
* According to country.

!
83
In fog or snow, the brightness
sensor may detect suffi cient light.
Therefore, the lights will not come
on automatically.
Do not cover the brightness sensor,
coupled with the rain sensor and
located in the centre of the wind-
screen behind the interior mirror;
the associated functions would no
longer be controlled.
Coupling with the "Follow-me-home"
lighting
Association with the automatic lighting
provides the "follow-me-home" lighting
with the following additional options:
- selection of the duration of main-
taining of the lighting for 15, 30 or
60 seconds in the vehicle param-
eters on the multifunction display
confi guration menu,
- automatic activation of "follow-me- home" lighting when automatic lighting
is in operation.
Automatic lighting
The side lights and dipped headlamps
are switched on automatically, without
any action on the part of the driver, when
a low level of external light is detected
(sensor behind the interior mirror) or when
the windscreen wipers are switched on.
As soon as the brightness returns to a
suffi cient level or the windscreen wipers
are switched off, the lights are switched
off automatically.
"Follow-me-home" lighting
The dipped headlamps remain on tem-
porarily, after switching off the vehicle’s
ignition, to make the driver’s exit easier
in poor light.
Activation

 With the ignition off, activate a
"headlamp fl ash" using lever B .

 A second "headlamp fl ash" switches
the function off again.
Switching off
The "follow-me-home" lighting is
switched off automatically following the
door locking command, after a given
time. Activation

 Turn ring A to the "
AUTO
" position.
The automatic lighting is accompanied
by a message on the multifunction dis-
play. Operating fault
In the event of a malfunction of
the brightness sensor, the lights
come on accompanied by the
service warning light, an audible
signal and a message on the multifunction
display.
Have it checked by a PEUGEOT dealer.
Daytime lights *
On vehicles fi tted with daytime lights,
the dipped headlamps come on when
the vehicle is started.
This indicator light comes on
on the instrument panel.
The instruments and controls (instru-
ment panel, multifunction display, air
conditioning control panel, ...) are not
lit, unless the automatic switching on of
the lights mode is activated or the lights
are switched on manually.
Deactivation

 Turn ring A to a position other than
" AUTO " . Deactivation is accompanied
by a message on the multifunction dis-
play.
* According to country.

i
84
STATIC DIRECTIONAL
LIGHTING
When the dipped or main beam head-
lamps are on, this function enables the
beam to light the inside of the turn with
an additional angle of approximately
30°.
The use of this lighting is optimum above
all at low and average speed (city driving,
winding roads, ...).
with directional lighting Programming
Switching on
The system is switched on from a certain
speed and a certain angle of rotation of
the steering wheel.
Operating fault The function is activated or
deactivated via the multi-
function display confi gura-
tion menu.
By default, this function is
activated.
In the event of a malfunction,
this warning light fl ashes on
the instrument panel, accom-
panied by a message on the
multifunction display.
Have it checked by a PEUGEOT dealer.
Switching off
The system is switched off below a
certain angle of rotation of the steering
wheel.
It is switched off when reverse gear is
engaged.
HEADLAMP ADJUSTMENT
The initial setting is position
"0" .
To avoid causing a nuisance to other
road users, the height of the headlamps
should be adjusted in relation to the
load in the vehicle.

0 . 1 or 2 people in the front seats.

-. 3 people.

1. 5 people.

2.
5 people + maximum authorised load.

3. Driver + maximum authorised load.

without directional lighting