ECU PEUGEOT 207 2009 User Guide

Page 107 of 279

i
CHILD SAFETY
99
ISOFIX CHILD SEAT RECOMMENDED BY PEUGEOT AND APPROVED FOR YOUR VEHICLE
This child seat can also be used on seats which are not fi tted with ISOFIX mountings. In this case, it must be attached
to the vehicle seat using the three point seat belt.

Follow the instructions for fi tting the child seat given in the seat manufacturer's installation guide.

RÖMER Duo Plus ISOFIX (size category B1 )

Group 1: from 9 to 18 kg
Installed in the forwards-facing position.
Fitted with an upper strap to be secured on the upper ring B ,
referred to as the TOP TETHER.
Three seat body angles: sitting, reclining, lying.

Page 108 of 279

CHILD SAFETY
100
SUMMARY TABLE FOR THE INSTALLATION OF ISOFIX CHILD SEATS (SALOON)
In accordance with the European regulation, this table indicates the options for the installation of ISOFIX child seats on the
vehicle seats fi tted with ISOFIX mountings.
In the case of the universal and semi-universal ISOFIX child seat s, the child seat's ISOFIX size category, determined by a
letter from A to G , is indicated on the child seat next to the ISOFIX logo.

IUF: seat suitable for the installation of an I sofi x U niversal seat, " F orward facing" and secured using the "Top Tether" upper strap.

IL-SU: seat suitable for the installation an I sofi x S emi- U niversal seat which is:
- "rear facing" fi tted with a "Top Tether" upper strap or a stay,
- "forward facing" fi tted with a stay,
- an infant car seat fi tted with a "Top Tether" upper stra p or a stay.
For the securing of the "Top Tether" upper strap, refer to the "Isofi x Mountings" section.

X: seat which is not suitable for the installation of an I SOFIX seat of the size category indicated.

Weight of the child /indicative age


Less than 10 kg
(group 0)
Up to 6 months approx
Less than 10 kg
(group 0)

Less than 13 kg
(group 0+)
Up to 1 year approx
From 9 to 18 kg (group 1)
From 1 to 3 years approx

Type of ISOFIX child seat Infant car seat * "rear facing" "rear facing" "forward facing"

ISOFIX size category F G C D E C D A B B1

Universal and semi-universal
ISOFIX child seats which can be installed on the rear seats
IL-SU ** X IL-SU ** X IL-SU **
IUF **
IL-SU **
* The ISOFIX infant car seat, fi xed to the lowe r rings of a seat equipped with ISOFIX mountings, o ccupies the three rear seats.
To install it on the rear seats of a 3-door model, the fron t seat belt must be adjusted to the lowest position.
Infant car seats and "car cots" cannot be installed on the fron t passenger seat.
** The head restraint of the seat equipped with ISOF IX mountings must be removed and stored.

Page 109 of 279

CHILD SAFETY
101
SUMMARY TABLE FOR THE INSTALLATION OF ISOFIX CHILD SEATS (GTI)
In accordance with the European regulation, this table indicates the options for the installation of ISOFIX child seats on the
vehicle seats fi tted with ISOFIX mountings.
In the case of the universal and semi-universal ISOFIX child seat s, the child seat’s ISOFIX size category, determined by a
letter from A to G , is indicated on the child seat next to the ISOFIX logo.

IUF: seat suitable for the installation of an I sofi x U niversal seat, " F orward facing" and secured using the "Top Tether" upper strap.

IL-SU: seat suitable for the installation of an I sofi x S emi- U niversal seat which is:
- "rear facing" fi tted with a "Top Tether" upper strap or a stay,
- "forward facing" fi tted with a stay.
For the securing of the "Top Tether" upper strap, refer to the "Isofi x Mountings" section.

X: seat which is not suitable for the installation of an I SOFIX seat of the size category indicated.
Weight of the child /indicative age


Less than 10 kg
(group 0)
Up to 6 months approx
Less than 10 kg
(group 0)
Less than 13 kg
(group 0+)
Up to 1 year approx
From 9 to 18 kg (group 1)
From 1 to 3 years approx

Type of ISOFIX child seat Infant car seat *** "rear facing" "rear facing" "forward facing"

ISOFIX size category F G C * D ** E C * D ** A B B1

Universal and semi-universal
ISOFIX child seats which can be installed on the rear seats
X IL-SU IL-SU
IUF

IL-SU
* The corresponding front seat belt must be adjusted to the highest position minus one notch.
The corresponding front seat must be adjusted to the mid-way longitudinal position plus two notches.
** The corresponding front seat belt must be adjusted t o the highest position minus one notch.
*** Infant car seats and "car cots" cannot be installed on the front passenger seat.

Page 110 of 279

CHILD SAFETY
102
SUMMARY TABLE FOR THE INSTALLATION OF ISOFIX CHILD SEATS (SW)
In accordance with the European regulation, this table indicates the options for the installation of ISOFIX child seats on the
vehicle seats fi tted with ISOFIX mountings.
In the case of the universal and semi-universal ISOFIX child seat s, the child seat's ISOFIX size category, determined by a
letter from A to G , is indicated on the child seat next to the ISOFIX logo.

IUF: seat suitable for the installation of an I sofi x U niversal seat, " F orward facing" and secured using the "Top Tether" upper strap.

IL-SU: seat suitable for the installation an I sofi x S emi- U niversal seat which is:
- "rear facing" fi tted with a "Top Tether" upper strap or a stay,
- "forward facing" fi tted with a stay,
- an infant car seat fi tted with a "Top Tether" upper stra p or a stay.
For the securing of the "Top Tether" upper strap, refer to the "Isofi x Mountings" section.
(a) The head restraint where the ISOFIX seat is fi tted must be removed and stored safely.


Weight of the child /indicative age

Less than 10 kg
(group 0)
Up to 6 months approx
Less than 10 kg
(group 0)

Less than 13 kg
(group 0+)
Up to 1 year approx
From 9 to 18 kg (group 1)
From 1 to 3 years approx

Type of ISOFIX child seat Infant car seat * "rear facing" "rear facing" "forward facing"

ISOFIX size category F G C ** D E C ** D A B B1

Universal and semi-universal
ISOFIX child seats which can be installed on the rear seats
IL-SU (a) IL-SU (a) IL-SU (a)
IUF (a)
IL-SU (a)
* The ISOFIX infant car seat, fi xed to the lower rings o f a seat equipped with ISOFIX mountings, occupies the three rear
seats and prevents use of the 2/3 - 1/3 modularity.
Infant car seats and "car cots" cannot be installed on the fron t passenger seat.
** The front seat must be adjusted to the most forward p osition minus fi ve notches.

Page 123 of 279

!
SAFETY
115
For the airbags to be fully
effective, observe the following
safety rules:
Sit in a normal upright position.
Wear a correctly adjusted seat belt.
Do not leave anything between the
occupants and the airbags (a child,
pet, object...). This could hamper the
operation of the airbags or injure the
occupants.
After an accident or if the vehicle has
been stolen or broken into, have the
airbag systems checked.
All work on the airbag system is strict-
ly forbidden unless it is carried out by
qualifi ed personnel of the PEUGEOT
dealer network.
Even if all of the precautions men-
tioned above are observed, a risk of
injury or of slight burns to the head,
chest or arms when an airbag is trig-
gered cannot be ruled out. In fact, the
bag infl ates almost instantly (within a
few milliseconds) then defl ates within
the same time discharging hot gas via
the openings provided for this pur-
pose. Front airbags
Do not drive holding the steering wheel by its spokes or resti
ng your hands on
the centre part of the wheel.
Passengers must not place their feet on the dashboard.
Smoke as little as possible as deployment of the airbags can cau se burns or the
risk of injury from a cigarette or pipe.
Never remove or pierce the steering wheel or hit it violently.
Side airbags *
Only put approved covers on the seats. These will not hinder the infl ation of the
side airbags. Consult a PEUGEOT dealer.
Do not fi x or attach anything to the seat backs. This could cause injury to the
chest or arms when the side airbag infl ates.
Do not sit with the upper part of the body any nea rer to the door than necessary.
Curtain airbags *
Do not fi x or attach anything to the roof. This could cause injury to the head
when the curtain airbag infl ates.
Do not remove the grab handles installed on the ro of, they play a part in securing
the curtain airbags.
* According to country.

Page 137 of 279

i
130
BONNET
Protects the components of the engine and provides access for checking levels.
 Push the exterior control B to the left and raise the bonnet.
 Unclip the strut C from its housing.
Fix the strut in one of the two notchesto hold the bonnet open.
Closing
 Take the strut out of the support notch.
 Clip the strut in its housing.
 Lower the bonnet and release it at the end of its travel.
 Pull on the bonnet to check that it is secured correctly.
RUNNING OUT OF FUEL
(DIESEL)
If your vehicle is fi tted with an HDI engine, the fuel circuit must be reprimed if you run out of fuel (refer to the corre-sponding graphic).
This system consists of a repriming pump and a transparent pipe.
Opening
 Open the front left door.
 Pull the interior control A , located at the bottom of the door frame.
1.4 litre Turbo HDI engine
 Open the bonnet.
 Fill the fuel tank with at least fi ve litres of diesel.
 Squeeze and release the repriming pump until fuel appears in the trans-parent pipe.
 Operate the starter until the engine starts.
 Close the bonnet.
1.6 litre Turbo HDI 16V engine
 Open the bonnet.
Fill the fuel tank with at least fi ve litres of diesel.
 Unclip the style cover to gain access to the repriming pump.
Squeeze and release the repriming pump until fuel appears in the trans-parent pipe with the green connector.
 Operate the starter until the engine starts.
 Put the style cover back in position and clip it in place.
 Close the bonnet.

Page 147 of 279

i
139
CHANGING A WHEEL *
Procedure for changing a faulty wheel
for the spare wheel using the tools pro-
vided with the vehicle.
The tools are installed in the boot under
the fl oor.
To gain access to them:

 open the boot,

 raise the fl oor,

 secure it by hooking the cord(s) on
the hook(s) on the rear shelf support,

 remove the box containing the tools.
Access to the tools
List of tools

1. Wheelbrace.
Permits removal of the wheel trim and removal of the wheel fi xing
bolts.

2. Jack with integral handle.
Permits raising of the vehicle.

3. "Bolt cover" tool.
Permits removal of the bolt pro- tectors (covers) on alloy wheels.

4. Socket for the security bolts (lo-
cated in the glove box).
Permits adaptation of the wheel- brace to the special "security"
bolts.
5. Removable towing eye.
Refer to the paragraph "Towing
the vehicle".
Other accessories
Wheel with trim

When removing the wheel , detach
the trim fi rst using the wheelbrace 1
pulling at the valve passage hole.

When refi tting the wheel , refi t the
trim starting by placing its notch
facing the valve and press around
its edge with the palm of your
hand.
All of these tools are specifi c to your
vehicle. Do not use them for other
purposes.
* According to country.

Page 148 of 279

i
i
140
Access to the spare wheel
(Saloon)
The spare wheel is installed in the boot
under the fl oor.
To gain access to it, refer to the paragraph
"Access to the tools" on the previous
page. Fitting the steel spare wheel
If your vehicle is fi tted with al-
loy wheels, it is normal to notice,
when tightening the bolts on fi tting,
that the washers do not come into
contact with the steel spare wheel.
The wheel is secured by the coni-
cal contact of each bolt. Taking out the wheel

 Unscrew the yellow central bolt.

 Raise the spare wheel towards you
from the rear.

 Take the wheel out of the boot.
Putting the wheel back in place

 Put the wheel back in its housing.

 Unscrew the yellow central bolt by a
few turns then put it in place in the
centre of the wheel.

 Tighten fully until the central bolt
clicks to retain the wheel correctly.

 Put the box back in place in the centre
of the wheel.

 Put the boot fl oor back in place.
Tyre under-infl ation detection
The spare wheel is not fi tted with
a sensor. The punctured wheel
must be repaired by a PEUGEOT
dealer.

Page 149 of 279

i
i
141
Access to the spare wheel (SW)
The spare wheel is installed in the boot
under the fl oor.
To gain access to it, refer to the para-
graph "Access to the tools". Fitting the steel spare wheel
If your vehicle is fi tted with al-
loy wheels, it is normal to notice,
when tightening the bolts on fi tting,
that the washers do not come into
contact with the steel spare wheel.
The wheel is secured by the coni-
cal contact of each bolt. Taking out the wheel

 Unscrew the yellow central bolt.

 Raise the spare wheel towards you
from the rear.

 Take the wheel out of the boot.
Putting the wheel back in place

 Put the wheel back in its housing.

 Unscrew the yellow central bolt by a
few turns then put it in place in the
centre of the wheel.

 Tighten fully until the central bolt
clicks to retain the wheel correctly.

 Put the box back in place in the centre
of the wheel.

 Put the boot fl oor back in place.
Tyre under-infl ation detection
The spare wheel is not fi tted with
a sensor. The punctured wheel
must be repaired by a PEUGEOT
dealer.

Page 150 of 279

i
142
Parking the vehicle
Immobilise the vehicle where it
does not block traffi c: the ground
must be level, stable and non-slip-
pery.
Apply the handbrake, switch off the
ignition and engage fi rst gear * to
lock the wheels.
If necessary, place a chock under
the wheel diagonally opposite the
wheel to be changed.
It is imperative that you ensure that
the occupants get out of the vehicle
and wait where they are safe.
Never go underneath a vehicle
raised using a jack; use an axle
stand.
Removing the wheel
List of operations

 Remove the chromed bolt cover from
each of the bolts using the tool 3 .

 If your vehicle is equipped with
this, fi t the security socket 4 on the
wheelbrace 1 to slacken the security
bolt.

 Slacken the other bolts using the
wheelbrace 1 only.

 Place the jack 2 in contact with one
of the two front A or rear B locations
provided on the underframe, which-
ever is closest to the wheel to be
changed.

 Extend the jack 2 until its base plate
is in contact with the ground. Ensure
that the centreline of the jack base
plate is directly below the location A
or B used.

 Raise the vehicle until there is suf-
fi cient space between the wheel and
the ground to admit the spare (not
punctured) wheel easily.

 Remove the bolts and store them in
a clean place.

 Remove the wheel.
* position R for the "2 Tronic" gear-
box; P for the automatic gearbox.

Page:   < prev 1-10 11-20 21-30 next >