headlamp PEUGEOT 207 2009 Owner's Manual

Page 157 of 279

!
149
Changing the third brake lamp bulbs
(4 bulbs W 5 W)

 Remove the two lamp fi xing nuts.

 Remove the lamp from the outside.

 Press on the two tabs and remove
the bulb holder

 Pull the bulb and change it.
To refi t, carry out these operations in re-
verse order.
Tighten the fi xing bolt suffi ciently by
hand to guarantee the sealing of the
lamp. Changing the number plate bulbs
(W 5 W)

 Insert a thin screwdriver into one of
the exterior holes of the lens.

 Push it towards the outside to unclip it

 Remove the lens.

 Pull the bulb and change it.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist
on the headlamps, the lamps and
their surrounds, to avoid damag-
ing their protective coating and
seals.

Page 160 of 279

152

Fuse N° Rating Functions

F8 20 A Audio equipment, audio/telephone, multifunction
screen, clock, steering wheel controls, tyre under-
infl ation detection, trailer fuse box.

F9 30 A Front 12 V socket, rear 12 V socket (SW).

F10 15 A Alarm siren, alarm control unit, directional
headlamps.

F11 15 A Diagnostic socket, low current ignition switch,
automatic gearbox control unit.

F12 15 A Rain/brightness sensor, amplifi er, trailer fuse box,
driving school module.

F13 5 A Engine fusebox, ABS relay, dual-function brake
switch, "2 Tronic" gearbox gear lever.

F14 15 A Instrument panel, seat belt warning lamps bar,
headlamp adjustment, air conditioning, hands-free
kit, rear parking assistance control unit, airbags.

F15 30 A Locking and deadlocking.

F17 40 A Rear screen and exterior mirrors demist/defrost.

SH - PARC shunt.

Page 161 of 279

153
Engine compartment fuses
The fuse box is placed in the engine
compartment, near the battery (left-
hand side).
Access to the fuses

 Unclip the cover.

 Replace the fuse (refer to the cor-
responding paragraph).

 When you have fi nished, close the
cover carefully to ensure the sealing
of the fuse box. Fuse table

Fuse N° Rating Functions

F1 20 A Engine control unit and fan assembly control relay
supply, timing and canister electrovalves (1.6 l
16V THP), air fl ow sensor (Diesel), injection pump
(Diesel), water in diesel sensor (Diesel), EGR
electrovalves, air heating (Diesel).

F2 15 A Horn

F3 10 A Front and rear wash-wipe.

F4 20 A Headlamp wash.

F5 15 A Fuel pump (petrol), Turbo electrovalves (1.6 l 16V
THP).

F6 10 A Vehicle speed sensor, automatic gearbox.

F7 10 A Electric power steering, directional headlamps,
directional headlamps control relay, switching and
protection unit (Diesel).

F8 25 A Starter control.

F9 10 A ABS/ESP control unit, brake pedal switch.

F10 30 A Engine control unit actuators (petrol: ignition coils,
electrovalves, oxygen sensors, injectors, heaters,
controlled thermostat) (Diesel: solenoid valves,
heaters).

F11 40 A Air conditioning blower.

F12 30 A Windscreen wipers Low/High speed.

Page 162 of 279

154

Fuse N° Rating Functions

F13 40 A Built-in systems interface supply (ignition positive).

F14 30 A Diesel heater (Diesel).

F15 10 A Left main beam headlamp.

F16 10 A Right main beam headlamp.

F17 15 A Left dipped beam headlamp.

F18 15 A Right dipped beam headlamp.
* The maxi-fuses provide additional protection for the electrical systems.
All work on the maxi-fuses must be
carried out by a PEUGEOT dealer. Maxi-fuse table

Fuse N° Rating Functions

Box 1

MF1 * 70 A Fan assembly.

MF2 * 20 A/30 A ABS/ESP pump.

MF3 * 20 A/30 A ABS/ESP electrovalves.

MF4 * 60 A Built-in systems interface supply.

MF5 * 60 A Built-in systems interface supply.

MF6 * 30 A Additional fan assembly (1.6 l 16V THP).

MF7 * 80 A Passenger compartment fusebox.

Box 2

MF8 * 30 A "2 Tronic" gearbox ECU.

MF9 * 80 A Heating unit (Diesel).

MF10 * 80 A Electric power steering.

MF11 * 40 A Valvetronic electric motor (1.6 l 16V THP).

Page 166 of 279

!
i
157
A fl at battery prevents the engine
from starting (refer to the corre-
sponding paragraph).
If the telephone is being used at
this time:
-
it will be maintained for 5 minutes
with your PC Sound hands-free kit,
- it will still be possible to fi nish the call with the PC Com.
ENERGY ECONOMY MODE
System which manages the duration of
use of certain functions to conserve a
suffi cient level of charge in the battery.
After the engine has stopped, you can
still use functions such as the audio
equipment, windscreen wipers, dipped
headlamps, courtesy lights, etc. for a
maximum combined duration of thir-
ty minutes. Exiting economy mode
These functions are reactivated auto-
matically next time the vehicle is driven.

 In order to resume the use of these
functions immediately, start the en-
gine and let it run for a few minutes.
The time available to you will then
be double the duration for which the
engine is left running. However, this
period will always be between fi ve and
thirty minutes.
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multi-func-
tion display indicating that the vehicle
has switched to economy mode and the
active functions are put on standby. CHANGING A WIPER BLADE Procedure for replacing a worn wiper blade with a new one without the use of tools.
Removing a front or rear wiper
blade
 Raise the corresponding wiper arm.
Unclip the wiper blade and remove it.
Fitting a front or rear wiper
blade
 At the front, check the size of the wiper blade as the shorter blade is fi tted on the right-hand side of the vehicle.
 Put the corresponding new wiper blade in place and clip it.
 Fold down the wiper arm carefully.

Page:   < prev 1-10 11-20 21-30