Peugeot 207 CC Dag 2007 Workshop Manual

!i!
56
REAR SEATS
Fixed two-seat bench fitted with roll-over bars to guarantee your protection should the vehicle roll over.
Rear head rests*
The rear seat backs are pre-fitted with the head rest fixings.
The head rests are available as ac-cessories. To obtain them, contact a PEUGEOT dealer.
For the installation of the rear head rests, refer to the "Practical information - § Rear head rests" section.
6. Heated seats switch
With the engine running, the front seats can be heated separately.
 Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating re-quired:
0: Off.
1: Low.
2: Medium.
3: High.
STEERING WHEEL
ADJUSTMENT
The height and depth of the steering wheel can be adjusted to adapt the driv-ing position to the size of the driver.
Adjustment
When stationary, pull the control to unlock the steering wheel.
 Adjust the height and depth.
 Push the control to lock the steering wheel.
* During the year.

!i!
56
REAR SEATS
Fixed two-seat bench fitted with roll-over bars to guarantee your protection should the vehicle roll over.
Rear head rests*
The rear seat backs are pre-fitted with the head rest fixings.
The head rests are available as ac-cessories. To obtain them, contact a PEUGEOT dealer.
For the installation of the rear head rests, refer to the "Practical information - § Rear head rests" section.
6. Heated seats switch
With the engine running, the front seats can be heated separately.
 Use the adjustment dial, placed on the side of each front seat, to switch on and select the level of heating re-quired:
0: Off.
1: Low.
2: Medium.
3: High.
STEERING WHEEL
ADJUSTMENT
The height and depth of the steering wheel can be adjusted to adapt the driv-ing position to the size of the driver.
Adjustment
When stationary, pull the control to unlock the steering wheel.
 Adjust the height and depth.
 Push the control to lock the steering wheel.
* During the year.

i
!
57
MIRRORS
Exterior mirrors
Adjustable mirror permitting the lateral rearward vision necessary when over-taking or parking.
Adjustment
 Slide switch A to the right or to the left to select the corresponding mirror.
 Move knob B in all four directions to adjust.
 Return switch A to the centre posi-tion.
Folding
 from outside: lock the vehicle using the remote control or the key.
 from inside: with the ignition on, pull switch A rearwards.
Unfolding
 from outside: unlock the vehicle us-ing the remote control or the key.
 from inside: with the ignition on, pull switch A rearwards.

!
i
58
Interior mirror
Adjustable mirror permitting central rearward vision.
Adjustment
 Adjust the mirror to direct it correctly in the "day" position.
Automatic day/night model
System which automatically and gradu-ally changes between the day and night uses.
To avoid glare, the interior mirror darkens automatically in relation to the intensity of the light from the rear.
It clears as soon as the light (light beam of vehicles behind, sun...) decreases, so providing optimum visibility.
Switching on
 Switch on the ignition and press switch 1.
The indicator light 2 comes on and the mirror operates in automatic mode.Manual model
The mirror is fitted with a night anti-daz-zle device.
Day/night position
 Pull the lever to change to the "night" anti-dazzle position.
 Push the lever to change to the nor-mal "day" position.
Switching off
 Press switch 1.
The indicator light 2 switches off and the mirror remains at its clearest.

!
59
SUN VISOR
Component which protects against sunlight from the front or the side, also equipped with an illuminated courtesy mirror.
 With the ignition on, raise the conceal-ing flap; the mirror is lit automatically.
This sun visor is also equipped with a ticket holder.
MAT
Removable component which protects the carpet against exterior dirt.
Refitting
To refit the mat on the driver’s side:
 position the mat correctly,
 refit the fixings by pressing,
 check that the mat is secured cor-rectly.Fitting
When fitting the mat for the first time, use only the fixings provided in the wal-let attached.
Removal
To remove the mat on the driver’s side:
 move the seat as far back as pos-sible,
 unclip the fixings,
 remove the fixings, then the mat.

60
INTERIOR LAYOUT
1. Glove box with light
(see details on following page)
2. Storage compartment with non-slip mat
3. Card holder
4. Door tray
5. Storage compartment with non-slip mat
6. Ashtray with light/Lighter
(see details on following page)
7. Can holder

61
Glove box with light
This has an upper open storage com-partment, a recess and locations for storing a bottle of water, the vehicle’s handbook, ...
Its lid has locations for storing a pen, a pair of spectacles, tokens, cards, a can, ...
It is fitted with a lock.
 To open the glove box, raise the handle.
It is lit when the lid is opened.
Ashtray with light/Lighter
 Raise the lid to gain access to the ashtray and the lighter.
 To empty the ashtray, after opening, remove its receptacle.
 To use the lighter, press it and wait a few seconds until it pops out auto-matically.
 To connect a 12 V accessory (max power: 100 Watts), remove the lighter and connect the appropriate adaptor.
It houses the front passenger air bag disarming switch A and three sockets* B for connecting audio/video equipment (refer to the "Audio and Telematics" section to activate the auxiliary input sockets).
If the vehicle is fitted with air condi-tioning, it provides access to the ven-tilation nozzle C, which can be opened or closed, distributing the same condi-tioned air as the vents in the passenger compartment.
* With DT colour display only.

62
BOOT LAYOUT
1. Stowing rings
2. Luggage retaining net
(see details on following page)
3. Load space cover
(see details on following page)
4. Windstop storage case
(see details on following page)
5. Luggage retaining straps

i
!i
63
Hooked onto the stowing rings, this enables you to secure your luggage.
Luggage retaining net
In the "cabriolet" configuration, the lug-gage space in the boot is restricted.
Load space cover
When it has been removed and folded, the windstop should be stored in its pro-tective case.
This case can be stored by means of a strap on the right-hand side of the boot.
Windstop storage case

64
Windstop folded
FITTING/REMOVING THE
WINDSTOP
In the "cabriolet" configuration, the windstop improves comfort in the pas-senger compartment.
It is supplied folded in four in its protec-tive case.
Windstop unfolded
Fitting
 Clip the ends of the assemby until a click is heard.
 Unfold the windstop by opening the two parts to 90° until a click is heard.
 Unfold the windstop frame guides.
 Engage the guides in the pointslocated behind the rear seat belts.
 Unfold each of the two parts fully.