start stop button Peugeot 208 2019 User Guide

89
Deactivation/Reactivation
In certain circumstances, such as the need
to maintain the temperature in the passenger
compartment, it may be useful to deactivate the
Stop & Start system.
The system can be deactivated at any time,
once the ignition is switched on.
If the engine is in STOP mode, it then restarts.
The Stop & Start system is reactivated
automatically every time the ignition is switched
on.Opening the bonnet Driving on flooded roads
Before driving through a
flooded road, it is
strongly recommended that you deactivate
the Stop & Start system.
For more information on Driving advice ,
particularly on flooded roads, refer to the
corresponding section.
Malfunction
The Stop & Start system requires a 12 V
b attery of specific technology and
specification.
All work on this type of battery must be
carried out only by a
PEUGEOT dealer or
a


qualified workshop.
For more information on the 12
V batter y,
refer to the corresponding section.
F

T

o deactivate or reactivate the system,
press this button.
The indicator lamp is lit when the system is
deactivated.
Before doing anything under the bonnet,
deactivate the Stop & Start system to avoid
the risk of injury related to an automatic
change to START mode.
Under-inflation detection
This system automatically monitors the tyre
pressure while driving.
The system monitors the pressure in all four
tyres, once the vehicle is moving.
It compares the information given by the
wheel speed sensors with reference values,
which must be reinitialised after ever y tyre
pressure adjustment or wheel change .
The system triggers an alert as soon as it
detects a
drop in the pressure of one or more
tyres.
In the event of a

fault with the system, the ECO
OFF switch warning lamp flashes, then comes
on fixed.
Have it checked by a

PEUGEOT dealer or
a


qualified workshop.
If a

fault occurs in STOP mode, the vehicle
may stall. All of the instrument panel warning
lamps come on. It is then necessary to switch
the ignition off and to restart the engine using
t h e key.
6
Driving

94
Temporarily exceeding the
speed
It is possible to accelerate and temporarily
drive at a speed higher than the programmed
speed setting.
The programmed value flashes.
When the accelerator pedal is released, the
vehicle will return to the programmed speed
setting.
Pause (OFF)
- Press this button or the brake or clutch pedal (depending on version).
With 1.2
PureTech 82 and 110 (Euro
6.2) or 1.5
BlueHDi (Euro 6.2) engines
with a
manual gearbox and Stop & Start,
pressing the clutch pedal does not pause
the cruise control: the cruise control
remains active after changing gears.
Resume
F After the cruise control has been paused, press this button.
The vehicle returns to the last registered speed.
Alternatively, you can also resume the
procedure for "Registering a
cruise speed
setting".
Changing the registered
speed setting
To register a speed higher t han the previous
setting, there are two possibilities.
Without using the accelerator
F Press the SET + button.
A short press increases the speed setting by
1

mph (km/h).
Pressing and holding increases the setting in
steps of 5

mph (km/h).
Using the accelerator
F Exceed the registered speed until you reach the desired speed.
F

P
ress the SET + or
SET – button.
To register a
speed lower than the previous
setting:
F

P
ress the SET –
button.
Driving

7
"Navigation " voice
commands
These commands can be made from any
screen page after pressing the " Voice
commands" or "Telephone" button located
on the steering wheel, as long as there is
no telephone call in progress. Voice commands
Help messages
Navigate home To start guidance or add a
stopover, say
"navigate to" and then the address or contact
name. For example, say "navigate to address
11
Regent Street, London", or "navigate to
contact, John Miller". You can specify if it's
a
preferred or recent destination. For example,
say "navigate to preferred address, tennis club",
or "navigate to recent destination, 11
Regent
Street, London" or just "navigate home". To
see points of interest on the map, you can say
things like "show hotels in Banbury" or "show
nearby petrol stations". For more information,
say "guidance help".
Navigate to work
Navigate to preferred address <…>
Navigate to contact <…>
Navigate to address <…>
Show POI <…>
Remaining distance
To get information about your current route, you
can say &#34;remaining time&#34;, &#34;remaining distance&#34;
or &#34;arrival time&#34;. Say &#34;navigation help&#34; to learn
more commands.
Remaining time
Arrival time
Stop guidance
Depending on the country, give the
destination instructions (address) in the
language used by the system.
.
PEUGEOT Connect Nav