change time Peugeot 3008 Hybrid 4 2012 Owner's Manual - RHD (UK. Australia)

Page 39 of 284

HY
B
37
Automatic restarting of the Diesel engine or ZEV mode NOT available

The internal combustion engine may
restart or ZEV mode may not be avail-
able in the various conditions presented
below.
The internal combustion engine can
be switched off automatically as soon
as these conditions are lifted.
When the conditions described below
cause the vehicle to come out of ZEV
mode and the Diesel engine to restart,
the vehicle automatically changes to
AUTO mode.

Action by the driver


- Moving the gear selector to posi-
tion M
.

- Action on steering mounted control
paddles to change gear.

- Sustained and sharp acceleration.

- Use of demisting.

- Use of air conditioning.

Maintaining the performance of the
system


- When the vehicle exceeds 18 mph
(30 km/h) after moving off (if the in-
ternal combustion engine has not
already started since the vehicle
was last started).

- If the high voltage battery is not
suffi ciently charged. A minimum of
4 bars in ZEV mode so as to en-
sure operation over a certain dis-
tance (in AUTO, electric operation
is accessible for a shorter period
with a lower level of charge).

- When the fuel level enters the
reserve zone (where rate of con-
sumption of this reserve is high,
ZEV inhibition may continue for
some time after refuelling).

- During regeneration of the par-
ticle emissions fi lter, which occurs
automatically for 5 to 10 minutes,
approximately every 300 miles
(500 kms) (or less in extended ur-
ban running).

Diffi cult weather conditions and
circumstances


- If certain conditions or engine
temperature requirements make
it necessary (such as an engine
temperature that is too low for the
ambient conditions).

- When the battery is close to maxi-
mum charge (for example: when
going down a long hill), because
engine recovery being no longer
possible, the internal combustion
engine restarts automatically just
to provide engine braking.

- If the vehicle encounters a steep
slope (car park ramp, ...).

- If the vehicle has been parked in
the sun for a prolonged period.

- When driving in mountainous con-
ditions (altitude).



Your vehicle is fi tted with the most
effective emissions control systems,
in particular the Particle Emissions
Filter (PEF).
At regular intervals your Diesel en-
gine will produce energy for the self-
cleaning of this fi lter.
During this PEF regeneration phase,
electric running is purposely made
unavailable.

Page 41 of 284

HY
B
39
ECO-DRIVING
Eco-driving is a range of everyday practices that allow the motorist to optimise their fuel consumption and CO2 emis-
sions.
Optimise the use of your gearbox

Use automatic mode A
as much as pos-
sible as this optimises gear changes to
suit the circumstances.

Drive smoothly


If your vehicle has cruise control, make
use of the system at speeds above
25 mph (40 km/h) when the traffi c is
fl owing well.



Control the use of your electrical equipment


Before moving off, if the passenger
compartment is too warm, ventilate it by
opening the windows and air vents be-
fore using the air conditioning.
Above 30 mph (50 km/h), close the win-
dows and leave the air vents open.
Remember to make use of equipment
that can help keep the temperature in
the passenger compartment down (sun
roof and window blinds...).
Switch off the air conditioning, unless
it has automatic digital regulation, as
soon as the desired temperature is at-
tained.
Switch off the demisting and defrosting
controls, if not automatic.
Switch off the heated seat as soon as
possible.

Switch off the headlamps and front fo-
glamps when the level of light does not
require their use.
Avoid running the Diesel engine when
stationary, particularly in winter; your
vehicle will warm up much faster while
driving.

As a passenger, if you avoid connect-
ing your multimedia devices (fi lm, mu-
sic, video game...), you will contribute
towards limiting the consumption of
electrical energy, and so of fuel.
Disconnect your portable devices be-
fore leaving the vehicle.

Maintain a safe distance between ve-
hicles, use engine braking rather than
the brake pedal, and press the accel-
erator progressively. These practices
contribute towards a reduction in fuel
consumption and CO
2 emissions and
also helps reduce the background traf-
fi c noise.

Page 63 of 284

61
IN
S
Total distance recorder
System which measures the total distance
travelled by the vehicle during its life.
Lighting dimmer
System for manual adjustment of the
brightness of the instrument panel in re-
lation to the exterior brightness.
The total and trip distances are dis-
played for thirty seconds when the ig-
nition is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.
Tr ip distance recorder


)
With the ignition on, press the but-
ton until zeros appear.

Activation
When the vehicle lighting is on:


)
press the button to change the
brightness of the instrument panel,

)
when the lighting reaches the mini-
mum setting, release the button,
then press again to increase it,
or


)
when the lighting reaches the maxi-
mum setting, release the button,
then press again to reduce it,

)
when the lighting reaches the level
of brightness required, release the
button.

When the vehicle lighting is
on, you cannot switch the in-
strument panel lighting off but
you can adjust it to minimum.

Deactivation
When the lighting is off, or in day mode
on vehicles fi tted with daytime running
lamps, pressing the button does not
have any effect.


To conform to legislation in the country
you are crossing, change the units of
distance (miles or km) via the confi gu-
ration menu.

System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.

Page 64 of 284

M
U
62
MONOCHROME SCREEN C (WITH PEUGEOT CONNECT SOUND (RD5)) Main menu

Displays in the screen

Displays according to context:


- time,

- date,

- ambient temperature with air condi-
tioning (the value displayed fl ashes if
there is a risk of ice),

- status of the openings (doors, boot...),

- audio functions,

- trip computer (see "trip computer"),

- alert messages,

- screen and vehicle equipment pa-
rameter setting menus.



"Audio functions" menu Controls

From the audio equipment control panel,
you can:


)
press the " MENU
" button for access
to the main menu
,

)
press the " 
" or " 
" buttons to scroll
through the items on the screen,

)
press the " MODE
" button to change
the permanent application (trip com-
puter, audio source...),

)
press the " 
" or " 
" buttons to
change a setting value,

)
press the " OK
" button to confi rm,
or

)
press the " ESC
" button to abandon
the operation in progress.




)
Press the "MENU"
button for access
to the main menu
:


- audio functions,

- trip computer (see "trip computer"),

- personalisation-confi guration,

- telephone (Bluetooth system).



For more information on the
"Audio functions" application,
refer to the Peugeot Connect
Sound (RD5) section.





)
Press the " 
" or " 
" button to se-
lect the menu required, then confi rm
by pressing the " OK
" button.



With the audio equipment switched on,
once this menu has been selected you
can activate or deactivate the functions
linked with use of the radio (RDS, REG,
RadioText) or CD (introscan, shuffl e,
CD repeat).

Page 66 of 284

M
U
64

Display confi guration
Once this menu has been selected, you
have access to the following settings:


- brightness-video setting,

- date and time setting,

- selection of the units.


Choice of language
Once this menu has been selected,
you can change the screen display
language (Deutsch, English, Espanol,
Français, Italiano, Nederlands, Portugues,
Portugues-Brasil, Türkçe * ).


Example: setting of the duration of the
guide-me-home lighting


)
Press the " 
" or " 
" buttons, then
the " OK
" button to select the menu
required.




)
Press the " 
" or " 
" buttons, then the
" OK
" button to select the "Guide-me-
home headlamps" line.




)
Press the " 
" or " 
" buttons to set the
value required (15, 30 or 60 seconds),
then press the " OK
" button to confi rm.



)
Press the " 
" or " 
" buttons, then
the " OK
" button to select the " OK
"
box and confi rm or press the " ESC
"
button to cancel.



"Telephone" menu
With the audio equipment switched on,
once this menu has been selected you
can confi gure your Bluetooth hands-free
kit (pairing), consult the various telephone
directories (calls log, services...) and man-
age your communications (pick up, hang
up, call waiting, secret mode...).

For safety reasons, confi gu-
ration of the multifunction
screen by the driver must only
be done when stationary.

For more information on the
"Telephone" application, refer
to the Peugeot Connect Sound
(RD5) section.

*
According to country.

Page 68 of 284

M
U
66

"SETUP" menu




)
Press the "SETUP"
button for access
to the "SETUP"
menu. This allows you
to select from the following functions:


- "Languages and voice functions",

- "Date and time",

- "Display",

- "Units",

- "System".



Language and voice functions
This menu allows you to:


- select the language used by the
screen (Deutsch, English, Espanol,
Français, Italiano, Nederlands,
Polski, Portugues, Türkçe * ),

- select the voice recognition param-
eters (activation/deactivation, advice
on use, personal voice programming,
etc.),

-
set the volume of the voice synthesiser.




Date and time
This menu allows you to set the date
and time, the format of the date and the
format of the time.

Principle of GPS synchronisation (GMT).


- Confi rm the selection "Synchronise
with GPS", the time is then aligned
with GMT universal time, the date is
also set.

- using the navigator, move the cursor
onto the hours fi eld and press OK
.

- You can then adjust the time to the
time zone of your choice, using the
rotating ring.
Please note that in the event of a
change of summer/winter time, the
time zone must be changed again
manually.


Display
This menu allows you to set the bright-
ness of the screen, the screen colour
scheme and the colour of the map (day/
night or auto mode).

Units
This menu allows you to select the units:
temperature (°C or °F) and distance
(miles or km).

For safety reasons, confi guration
of the multifunction screen by the
driver must only be done when
stationary.

*
According to country of sale.
System parameters
This menu allows you to restore the factory
confi guration, display the software version
and activate scrolling text.

Page 170 of 284

CHECKS
168
Avoid prolonged contact of
used oil or fl uids with the skin.
Most of these fl uids are harmful to
health or indeed very corrosive.
Do not discard used oil or
fl uids into sewers or onto the
ground.
Take used oil to a PEUGEOT dealer
or a qualifi ed workshop (France) or
to an authorised waste disposal site.









Diesel additive level (Diesel engine
with particle emission filter)








Used products


Topping up
This additive must be topped up by a
PEUGEOT dealer or a qualifi ed work-
shop without delay.






Before doing anything under
the bonnet, switch off the igni-
tion ( Ready
lamp off) to avoid
any risk of injury resulting from auto-
matic operation of the engine.
Fluid specifi cation
For optimum cleaning and to avoid
freezing, this fl uid must not be topped
up with or replaced with plain water.

Unless otherwise indicated, check these
components in accordance with the servic-
ing booklet and according to your engine.
Otherwise, have them checked by a
PEUGEOT dealer or a qualifi ed work-
shop.

The battery does not require
any maintenance.
However, check that the terminals
are clean and correctly tightened,
particularly in summer and winter.
When carrying out work on the battery,
refer to the "Practical information" sec-
tion for details of the precautions to be
taken before disconnecting the battery
and following its reconnection.













12 V battery




















Air filter and passenger compartment filter


Refer to the servicing booklet
for details of the replacement
intervals for these compo-
nents.
Depending on the environment
(e.g. dusty atmosphere) and the use of
the vehicle (e.g. city driving), replace
them twice as often if necessary
.
A clogged passenger compartment fi lter
may have an adverse effect on the per-
formance of the air conditioning system
and generate undesirable odours.















Oil filter

Replace the oil fi lter each time
the engine oil is changed.
Refer to the servicing booklet
for details of the replacement
interval for this component. A low additive level is indicated
by illumination of the service
warning lamp, accompanied
by an audible warning and a
message in the instrument
panel screen.

Page 181 of 284

PRACTICAL INFORMATION
179







Changing dipped / main beam
headlamp bulbs


)
Remove the protective plastic cover
by pulling on the tab.

)
Disconnect the bulb connector.

)
Turn the bulb holder.

)
Pull out the bulb and change it.
To r efi t, carry out these operations in re-
verse order.
CHANGING A BULB










1.
Direction indicators
(PY21W-21W).


2.
Dipped / main beam headlamps
(H9-12V-65W).


3.
Sidelamps / daytime running lamps
(light emitting diodes - LEDs).

4.
Foglamps (PS24-24W).



The headlamps are fi tted with
polycarbonate glass with a
protective coating:


)
do not clean them using a dry
or abrasive cloth, nor with a
detergent or solvent product,


)
use a sponge and soapy water,

)
when using a high pressure wash-
er on persistent marks, do not
keep the lance directed towards
the lamps or their edges for too
long, so as not to damage their
protective coating and seals,

)
do not touch the bulb directly with
your fi ngers, use lint-free cloths.


Front lamps


Changing a bulb should only be
done after the headlamp has been
switched off for a few minutes (risk of
serious burns).
It is imperative to use only anti-ultra-
violet (UV) type bulbs in order not to
damage the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specifi cation.


Changing the light emitting
diode-LED lamps
For replacement, contact a PEUGEOT
dealer or qualifi ed workshop.

Before doing any work on your
vehicle, switch off the ignition
( Ready
lamp off) to avoid any
risk of injury resulting from automatic
operation of the engine.

Page 189 of 284

PRACTICAL INFORMATION
187

Engine compartment fuses


Access to the fuses


)
Unclip the cover.

)
Change the fuse (see correspond-
ing paragraph).

)
When you have fi nished, close the
cover carefully to ensure correct
sealing of the fusebox.


The fusebox is placed in the engine
compartment near the battery.
Fuse
N°

Rating
(A)


Functions




F1



20

Engine control unit supply, injection pump and
EGR electrovalves, injectors.


F2



15

Horn.


F3



10

Front / rear wash-wipe.


F4



10

Daytime running lamps.


F5



15

Air fl ow sensor, wiper, sensor heater, hybrid control
unit, hybrid selector dial, electronic thermostat,
variable valve timing electrovalves, turbo pressure
regulation electrovalves (Diesel), engine coolant
level sensor (Diesel).


F6



10

Diagnostic socket, directional headlamps, particle
emission fi lter pump (Diesel), mirror adjustment
control, network interface unit, head-up display.


F7



10

Power steering control unit, directional headlamps
height adjustment motor.


F8



20

Starter motor control.


F9



10

Clutch and brake pedal switches.



F10



30

Heaters (Diesel).


F11



40

Air conditioning blower.

Page 201 of 284

PRACTICAL INFORMATION
199






"Transport solutions":

For leisure pursuits: roof bars, bicycle
carrier on towbar, bicycle carrier on roof
bars, ski carrier, roof box, booster seats
and child seats, side blinds, under shelf
storage.
Trailer towbar, which must be fi tted by a
PEUGEOT dealer.


"Safety and security":

anti-theft alarm, window etching, wheel
security bolts, fi rst aid kit, breathalyzer,
warning triangle, high visibility vest, sto-
len vehicle tracking system, dog guard,
snow chains.
You can also obtain cleaning
and maintenance products
(exterior and interior), products
for topping up (screenwash fl uid...)
and refi lls (sealant cartridge for the
temporary puncture repair kit...) from
PEUGEOT dealers.



*
To avoid any risk of jamming of the
pedals:


- ensure that the mat is positioned
and secured correctly,

- never fi t one mat on top of another.



"Style":

seat covers compatible with lateral air-
bags, leather gear lever knob, foglamps,
door defl ectors, spoiler, styling strips,
alloy wheels, trims, chrome-plated door
handle shells.


"Protection":

mats * , boot tray, luggage net, coat
hanger fi xed on head restraint, stainless
steel or carbon fi bre style door sills.


"Multimedia":

audio systems, amplifi ers, satellite navi-
gation systems, Bluetooth hands-free
system, CD changer, speakers, DVD
player, USB Box, front and rear parking
sensors, additional Bluetooth wireless
headphones, Bluetooth audio head-
phones mains charger.

Page:   1-10 11-20 next >