Ignition Peugeot 307 CC 2003 User Guide

22-09-2003
INSTRUMENTS AND CONTROLS
32
Low fuel level warning light
The warning light comes on for three seconds when the ignition isswitched on. When this light comes on with the engine running, it is accompanied byan audible signal and the message"Fuel level low" on the multi-function
display. When the warning light comes on, you have enough fuel to driveapproximately 30 miles (50 km) .
The tank capacity is approximately
60 litres. This light flashes to indicate a mal- function of the fuel gauge.
Contact a PEUGEOT dealer. Coolant temperature indicator When the needle is in zone
A, the
temperature is correct. When the needle is in zone B, the
temperature is too high. The central
STOP warning light flashes, accom-
panied by an audible signal and themessage "Engine coolant temper-
ature high" on the multi-function
display.
You must stop immediately.
Warning: wait for the engine to cool
before topping up the level.The cooling system is pressurised.In order to avoid any risk of scalding, unscrew the cap two turns to allowthe pressure to drop. When the pressure has dropped, remove the cap and top up the level.
Contact a PEUGEOT dealer. Engine oil temperature indicator When the engine is running, this indicates the oil temperature. The temperature is too high if the maximum graduation is reached.The central
STOPwarning light
flashes, accompanied by an audiblesignal.
You must stop immediately.
Contact a PEUGEOT dealer.
Seat belt not fastened warning light
With the engine running, this indica- tor light comes on when the driver'sseat belt is not fastened.

22-09-2003
Lighting rheostat With the lights on, press the button tovary the intensity of thelighting of the instru-ments and controls.
When the lighting reaches the mini-mum (or maximum) setting, release thebutton then press it again to increase(or reduce) the brightness. As soon as the lighting is of the required brightness, release the button.
Trip recorder zero reset With the ignition on, press the button.
Instrument panel display After switching on the ignition, three functions are shown in succession:
Ð service indicator (see corresponding section),
Ð engine oil level indicator,
Ð total distance recorder (total and trip distances).Note:
the total and trip distances are displayed for 30 seconds when the ignition
is switched off, on opening the driver's door, as well as on locking and unlocking the vehicle. Engine oil level indicator When the ignition is switched on, the engine oil level is indicated for approxi- mately 10 seconds, after the servicing information.
Surplus oil Flashing indicates a surplus of oil which can cause damage to the engine. If the surplus of oil is confirmed by checking using the dipstick,
contact a PEUGEOT dealer without delay. No oil Flashing indicates a lack of oil which can cause damage to the engine. If the lack of oil is confirmed by checking using the dipstick, it is essential to top up the level. Oil level gauge fault Check the oil level using the dipstick. If the level is correct, the flashing indicates a true engine oil level gauge fault.
Contact a PEUGEOT dealer.
INSTRUMENTS AND CONTROLS
34
The value obtained by checking the level using the dipstick is only correct if the vehicle has been on level ground, with the engine off, for more than 10 min
utes.

22-09-2003
YOUR 307 CC IN DETAIL
40
GENERAL FUNCTIONS On/off With the ignition key in the accessories or ignition position, press button Ato switch the set on or off.
The set can operate for 30 minutes without the vehicle ignition being switched on.
Anti-theft systemThe audio system is coded in such a way that it can operate only on your vehicle. It would not function if fitted to another vehicle. The anti-theft system is automatic and requires no action on your part. ADJUSTING THE VOLUME Press the button Cto increase the volume, or button Bto decrease it.
Continuous pressure on buttons Band Callows a gradual adjustment of the volume.
AUDIO SETTINGS Press button Gseveral times in succession to access the bass (BASS), treble (TREB), loudness (LOUD),
fader (FAD) , balance (BAL)and automatic volume correction settings.
Exit from audio mode is automatic after a few seconds without pressing any button, or by pressing button G
after configuration of the automatic volume correction. Note: bass, treble and loudness settings are specific to each source. It is possible to set them differently for
radio, CD or CD changer.

22-09-2003
YOUR 307 CC IN DETAIL
52
GENERAL FUNCTIONS On/off With the ignition switch in the accessories position or with the ignition on, press button Ato switch the audio
function of the RT3 audio/telephone on or off. Note: in the absence of an ignition key, press button Ato switch the telematics system on or off.
The RT3 audio/telephone can operate for 30 minutes without switching the vehicle ignition on.
Notes:
Ð the SIM card must be removed only after the audio/telephone has been switched off,
Ð following automatic switching off of the audio/telephone after 30 minutes it is possible to make a telephone call by pres- sing button D,
Ð after the ignition has been switched off, the audio/telephone can be switched on again by pressing buttons D, E , V or by
inserting a CD in the player.
Anti-theft system
The RT3 audio/telephone is coded in such a way that it can operate only on your vehicle. If fitting it to another vehicle, cons ult
your PEUGEOT dealer for configuration of the system. The anti-theft system is automatic and requires no action on your part. ADJUSTING THE VOLUME
Turn button Aclockwise to increase the volume of the audio/telephone or anti-clockwise to decrease it.
Note: the volume setting is specific to each source. It is possible to have different settings for radio, CD or CD changer.
AUDIO SETTINGS Press button Uto access Bass, Treble, Loudness, Fader (front/rear balance), Balance(left/right balance)
and Automatic volume adjustment settings.
Exit from audio mode is automatic after a few seconds without any action, or by pressing the "ESC"button.
Note: bass, treble and loudness settings are specific to each source. It is possible to have different settings
for radio, CD or CD changer.

22-09-2003
YOUR 307 CC IN DETAIL
60
TELEPHONE
This function is a GSM dual-band telephone (900 and 1 800 MHz) incorporated in the RT3 audio system. It is a "hands free" telephone. This function is provided by a microphone located next to the front courtesy light, the spea-
kers and a steering column control which allows access to most of the functions (the audio/telephone control panel buttons allow access to all the functions). Display of the principal "mobile"type functions, as well as consultation of the indexes, is provided by the multi-function
display.This function is active , whatever position the ignition key is in even after thirty minutes, when the message "Economy
mode active" appears on the multi-function display.
Using the menus Press the "MENU"button to display the general menu. Select the telematicsapplication, validate "Telephone functions"
to access the principal telephone functions, then the various menus, in order to reach the one required. This menu allows you to access the following functions:
Ð Network:allows you to select the network search mode and to see the networks avai-
lable.
Ð Duration of calls: allows you to consult the duration recorder of calls made and zero re-
set.
Ð Security: allows you to use or modify the PIN code and to erase the list of calls and
text messages (SMS).
Ð Telephone options: allows you to configure the calls with entering of my number,
automatic answering after X rings, specification of ring options and allows you to
configure the call diversion number.
Within each menu:
Move around and select a function by turning the Gbutton then validate by pressing the button.
Cancel an operation using the "ESC"button.

22-09-2003
YOUR 307 CC IN DETAIL
62
Inputting the PIN code Input your PIN code using the alphanumeric keypad and validate by pressing button Gor but-
ton #to access the network. Connection to the network is validated by the appearance of a sym-
bol on the screen.
Warning: if you make three errors in succession when inputting your PIN code, your SIM card
will be blocked. To unblock it, you will need to input the PUK code. The PUK code will be sup- plied to you by the person selling your SIM card (input of the PUK code allows for 10 errors insuccession; after this the SIM card becomes permanently unusable). Note: the PIN code is required each time the ignition is switched on, unless the PIN code has
been stored in the memory or protection by PIN code is not activated on the SIM card.
Cancelling of PIN code request In the menu "Telephone functions" select "Security" , then "Process the PIN code" , then validate the "Cancel"function.
Warning: in this case, do not lose your SIM card. Losing it would mean anyone who finds it would be able to make un-limited
calls.
Telephone function screens
Not in use This screen indicates the presence of voice messages or text messages (SMS) not lis- tened to/read, the cumulatve time in use since the last zero reset and the status of yourtelephone. In use This screen indicates the time elapsed since the start of the conversation, as well as the number* or name of the person to whom you are speaking (if recorded in the index)and the status of your telephone.
* If this option and service are available.

22-09-2003
YOUR 307 CC IN DETAIL77
The menu
''Guidance options''
provides access to the following functions:
Ð changing of the route calculation criteria,
Ð voice synthesis adjustment of gui- dance messages,
Ð description of the information rela- ting to the navigation CD-Rom,
Ð management of the addresses stored in the directory.
Guidance optionsThe last criterion used is displayed. Select a criterion from the list, then validate by pressing the dial. When the criterion of your choice has been selected, select the
"OK"
function then confirm by pressing thedial. Adjusting the voice synthesiser Select the type of voice "male" or
"female" , after inserting the configu-
ration CD-Rom. Adjust the volume of the voice syn- thesis by turning the dial, then vali-date by pressing the dial. Note: the volume can also be adjust-
ed during a message, using the audio/telephone button or the steer-ing wheel control. Management of the directory This function enables you to rename
an address stored in the directory. Select the description corresponding to the stored address to be changed. Select the
"Rename" function, then
confirm by pressing the dial. Select the "OK" function, then con-
firm by pressing the dial to record the changes made. Stopping/Resuming guidance
¥ "Stop guidance" During guidance, select this function then validate.
¥ "Resume guidance" In the absence of guidance, select this function then validate to activateguidance to the last destination pro-grammed. Note: after re-starting the engine, a
screen appears enabling you to resume guidance activated before
the ignition was switched off.
Calculation criteria

22-09-2003
YOUR 307 CC IN DETAIL91
SEAT BELTS
To lock the seat belts 
Pull the strap, then insert the buckle into the stalk. Pre-tensioning and force-limiting front seat belts Safety in the event of a frontal impact has been improved by the introduc-tion of pre-tensioning and force-limit-ing front seat belts. Depending onthe seriousness of the impact, thepre-tensioning system instantly tight-ens the seat belt firmly against thebody of the occupant. The pre-tensioning seat belts are armed when the ignition is on. The force-limiting device reduces the pressure of the seat belt against thebody of the occupant in the event ofan accident.
Rear seat belts The two rear seats are both fitted with three-point inertia reel seat beltswith force-limiting devices. Slide the straps in the guides
1to
prevent fluttering of the rear seat belts in cabriolet mode.
To be effective, a seat belt must be tightened as close to the body as possible. Depending on the nature and the seriousness of the impact, the pre- tensioners may be triggered before and independently of the air bags.
In all cases of triggering, the air bag warning light on the instrument panelcomes on.
After an impact, have the system checked by a PEUGEOT dealer.

22-09-2003
YOUR 307 CC IN DETAIL
92
THE KEYS
You have two identical keys. They allow you to switch on the ignitionand operate the passenger air bagdisarming switch and the boot open-ing button disarming switch as wellas to
independently operate the
lock on the driver's door, the fuel fillercap and the glove box. Central locking/Unlocking
From the driver's door, the keys allow you to:
Ð lock the doors and boot simultane- ously, as well as fold back the exterior mirrors,
Ð unlock the driver's door. Opening this door unlocks the passenger
door.
The boot can only be unlocked bypressing the locking/unlocking but-ton from inside the vehicle, with thekey in the switch (refer to the corre-sponding section). The remote control This permits remote locking, dead- locking and unlocking of the vehicle,locating of the vehicle, folding of theexterior mirrors and partial openingof the boot. Locking Press button
Ato lock the vehicle.
This is confirmed by fixed lighting of the direction indicators for approxi-mately two seconds.
Vehicles fitted with deadlocking
Warning: deadlocking renders the
internal and external door locking controls inoperative. Pressing button Adeadlocks the
vehicle. This is confirmed by fixed lighting of the direction indicators for approxi-mately two seconds. A second press
on button Awithin
five seconds of deadlocking changesthis to normal locking. This is confirmed by fixed lighting of the direction indicators for approxi-mately two seconds. Unlocking Press button Bto unlock the vehicle.
This is confirmed by rapid flashing of the direction indicators. Note: if the vehicle is locked and
unlocking is activated inadvertently, unless one of the doors or the boot isopened within 30 seconds, the vehi-
cle will lock automatically. Partial opening of the boot Press and hold button Bto partially
open the boot, in addition to unlock- ing the vehicle. Locating your vehicle
To locate your vehicle, if you have locked it, in a car park:  press button A, the courtesy
lights come on and the direction indicators flash for a few sec-onds.

22-09-2003
YOUR 307 CC IN DETAIL93
Confidential card The confidential card contains the identification code necessary for anywork carried out by a PEUGEOTdealer on the electronic immobiliser
system. This code is hidden by afilm, which should be removed only
if necessary. Keep your card in a safe place, never inside the vehicle. Key in ignition
A buzzer sounds on opening the dri-
ver's door, if the key has been left inthe ignition. Changing the battery of the remote control
Warning that the battery is flat is given by an audible signal accompa-nied by the message
''Remote con-
trol battery low'' on the multifunc-
tion display.
To replace the battery, remove the screw then unclip the casing using acoin at the ring (CR 2016/3 volt bat-tery). If the remote control does not work after the battery has been changed,reprogramme the remote control. Programming the remote control  Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove the remote control key
from the ignition lock. The remotecontrol is now working again.
ELECTRONIC ENGINE IMMOBILISER This locks the engine control system as soon as the ignition has been
switched off and therefore preventsstarting of the vehicle by anyone
who does not have the key. The ignition key has an electronic chip which has a special code.When the ignition is switched on, thecode must be recognised for startingto be possible. If the system does not function correctly , the central locking button
indicator light, situated in the centreof the fascia, flashes rapidly whenthe ignition is switched on (2ndnotch), accompanied by an audiblesignal and the message ''Anti-theft
device faulty'' on the multi-function
display. In this case your vehicle will not start.
Contact a PEUGEOT dealer as soon as possible.