display PEUGEOT 307 CC DAG 2007 Owners Manual

Page 13 of 184

FAMILIARISATION
SPEED LIMITER "LIMIT" Cruise control "CRUISE"
Display on the instrument panel

1. Cruise control mode Selection/
Off.

2. Programming of a speed/
Decreasing of the programmed
value.

3. Programming of a speed/
Increasing of the programmed
value.

4. Cruise control Off/Resume.
In order to be programmed or activat-
ed, the vehicle speed must be higher
than 25 mph (40 km/h), with at least
fourth gear engaged on the manual
gearbox (second for the automatic
gearbox).
 85, 87

1. Speed limiter mode Selection/Off.

2. Decreasing of the programmed
value.

3. Increasing of the programmed
value.

4. Speed limiter On/Off.
The values must be set with the en-
gine running.
 83

Cruise control

Speed limiter
The cruise control or speed limiter
mode appears on the instrument
panel when it is selected.

Page 14 of 184

FAMILIARISATION

1. Gear lever.

2. "SPORT" button.

3. "SNOW" button. Position selection gate
Move the lever in the gate to select
a position.
Once a position has been selected,
the corresponding indicator light is
displayed on the instrument panel
screen.

A. Switching on.

B. Detection.

C. Activation/Deactivation.
(via the multifunction display coni guration menu).
 89 Display on the instrument panel

P: Park.

R: Reverse.

N: Neutral.

D: Drive.

M: Manual mode.

S: Sport programme.


 : Snow programme.

1 2 3 4: gears engaged. Moving off
With the handbrake applied, select
position
P or N .
Switch on the ignition.
With the engine running, in position

P or N , with your foot on the brake
pedal, release the handbrake .
Select position R , D or M .
Gradually release the brake pedal;
the vehicle moves off immediately.
Visual and audible rear
parking assistance "PORSCHE TIPTRONIC
SYSTEM" automatic gearbox

 80

Page 22 of 184

24
INSTRUMENTS and CONTROLS
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).

Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since the last service.

Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.

Example: 4,800 miles/km remain
before the next service. For i ve sec-
onds after the ignition is switched on,
the display indicates:
INSTRUMENT PANEL DISPLAY
The distance remaining to the
next service is less than
500 miles (1,000 km).

Example: 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and

the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.

Page 23 of 184

24
INSTRUMENTS and CONTROLS
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).

Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver's door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer's servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since the last service.

Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er's driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.

Example: 4,800 miles/km remain
before the next service. For i ve sec-
onds after the ignition is switched on,
the display indicates:
INSTRUMENT PANEL DISPLAY
The distance remaining to the
next service is less than
500 miles (1,000 km).

Example: 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and

the spanner remains lit .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance.

Page 31 of 184

29
INSTRUMENTS and CONTROLS
Display C

 Press the "MENU" button to gain
access to the general menu.

 Press the arrows, then the "OK"
button to select the "Trip compu-
ter" menu.

 On the "Trip computer" menu,
select one of the following appli-
cations:
Warnings log
This summarises the active warning
messages, displaying them in suc-
cession on the multifunction display.
Status of the functions
This summarises the active or inac-
tive status of the functions present on
the vehicle.
Enter the distance to the
destination
This enables you to enter an approxi-
mate value for the distance to the i -
nal destination.
"TRIP COMPUTER" MENU
System which provides general in-
formation concerning the status of
certain equipment with which your
vehicle is equipped, such as the
warnings log, the status of the func-
tions...
"DIAGNOSTICS" MENU

 On the "Diagnostics" menu, se-
lect one of the following applica-
tions:
Colour display

 Press the "MENU" button to gain
access to the general menu.

 Turn the dial and press it to select
the "Diagnostics" menu.

Page 32 of 184

30
MULTIFUNCTION DISPLAYS
MONOCHROME DISPLAY C
(WITHOUT RD4 AUDIO EQUIPMENT)
Presentation
Three buttons and a navigator en-
able you to control the display:
- "MENU" to display the general
menu,
- to change the permanent appli-
cation (trip computer, date, ...),
- "ESC" to abandon the operation
in progress,
- Rotation of the navigator: move-
ment on the display or changing
of a setting,
- Press on the navigator: coni r-
mation of the selection.
It displays the following information:
- the time,
- the date,
- the exterior temperature (the val-
ue displayed l ashes if there is a
risk of ice),
- the accesses check (doors, boot, ...),
- the warning messages (e.g.: "Depollution system faulty") or
information messages (e.g.: "Au-
tomatic headlamp lighting activat-
ed"), displayed temporarily, can
be cleared by pressing the "ESC"
button,
- the trip computer (see corre- sponding section). Press the
"MENU" button to access
the general menu:
- trip computer (see corresponding section),
- personalisation-coni guration,
Turn the navigator to select the menu
required, then coni rm by pressing
the navigator.
Once this menu has been selected,
you can access the following
functions:
- dei ne the vehicle parameters,
- display coni guration,
- selection of the language.
Parameter configuration General menu
"Personalisation-
Configuration" menu

Page 33 of 184

!
31
MULTIFUNCTION DISPLAYS
Dei ne the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
lowing equipment:
- "follow-me-home" lighting and duration (refer to the "Visibility"
section),
- parking assistance (refer to the "Driving" section). Selection of the language
Once this menu has been selected,
you can change the language used
on the display (Deutsch, English,
Espanol, Français, Italiano, Neder-
lands, Portugues, Portugues-Brasil).
Display coni guration
Once this menu has been selected,
you can access the following set-
tings:
- brightness-video setting,
- date and time setting,
- selection of the units.
Once you have selected a setting,
press the navigator.
Turn the navigator to change the val-
ue of the setting selected.
Press the navigator to record the
change and move on to the next set-
ting or press the
"ESC" key to cancel.
Example: "Duration of the "follow-
me-home" lighting"
For safety reasons, coni gura-
tion of the multifunction displays
by the driver must take place
when stationary.

Page 34 of 184

32
MULTIFUNCTION DISPLAYS
MONOCHROME DISPLAY C
Controls
From the RD4 audio equipment con-
trol panel, you can:

 press the "MENU" button to gain
access to the general menu ,

 press the "  " or "  " buttons to
scroll through the items on the
screen,

 press the "MODE" button to
change the permanent application
(trip computer, audio source, ...),

 press the "  " or "  " buttons to
change a setting value,

 press the "OK" button to con-
i rm,
or

 press the "ESC" button to aban-
don the operation in progress.
Displays on the screen
This displays the following
information:
- the time,
- the date,
- the outside temperature * (this l ashes if there is a risk of ice),
- the status of the accesses (doors, boot, ...),
- the audio sources (radio, CD, ...),
- the trip computer (refer to the cor- responding section).

Warning messages (e.g.: "Emission
control system faulty") or information
messages (e.g.: "Automatic switch-
ing on of the headlamps activated")
may appear temporarily. These can be
cleared by pressing the "ESC" button.
General menu

 Press the "MENU" button to gain
access to the general menu :
- audio functions,
- trip computer (refer to the cor- responding section),
- personalisation-coni guration,
- telephone (hands-free kit).

 Press the "  " or "  " buttons to
select the menu required, then
coni rm by pressing the "OK"
button.
"Audio functions" menu
With the RD4 audio equipment
switched on, once this menu has
been selected you can activate or de-
activate the functions linked with use
of the radio (RDS, REG, RadioText),
the CD or the CD changer (introscan,
shufl e, CD repeat).
For further details concerning the
"Audio functions" application, refer to
the RD4 part of the "Audio and Tele-
matics" section.
"Trip computer" menu
Once this menu has been selected,
you can consult information concern-
ing the status of the vehicle (warn-
ings log, status of the functions, ...).

Page 35 of 184

!
33
MULTIFUNCTION DISPLAYS
"Personalisation-
Configuration" menu
Once this menu has been selected,
you can gain access to the following
functions:
- dei ne the vehicle parameters,
- display coni guration,
- selection of the language. Display coni guration
Once this menu has been selected,
you can gain access to the following
settings:
- brightness-video setting,
- date and time setting,
- selection of the units.

Example: setting of the duration of
the "follow-me-home" lighting

 Press the "  " or "  " buttons,
then the "OK" button to select
the menu required.

 Press the "  " or "  " buttons,
then the "OK" button to select
the "Lighting and signalling" line.

 Press the "  " or "  " buttons to
set the value required (15, 30 or
60 seconds), then press the "OK"
button to coni rm.
Dei ne the vehicle parameters
Once this menu has been selected,
you can activate or deactivate the fol-
lowing equipment:
- "follow-me-home" lighting (refer
to the "Visibility" section),
- parking assistance (refer to the "Driving" section).

 Press the "  " or "  " buttons,
then the "OK" button to select the

"OK" box and coni rm or press
the "ESC" button to cancel. Selection of the language
Once this menu has been selected,
you can change the language used
by the display (Deutsch, English,
Espanol, Français, Italiano, Neder-
lands, Portugues, Portugues-Brasil).
"Telephone" menu
With the RD4 audio equipment
switched on, once this menu has
been selected you can coni gure
your Bluetooth hands-free kit (match-
ing), consult the various telephone
directories (calls log, services, ...)
and manage your communications
(pick up, hang up, call waiting, secret
mode, ...).
For further details concerning the "Tele-
phone" application, refer to the RD4 part
of the "Audio and Telematics" section.
For safety reasons, it is impera-
tive that coni guration of the multi-
function displays by the driver
takes place when stationary.

Page 36 of 184

34
MULTIFUNCTION DISPLAYS
COLOUR DISPLAY
Displays on the screen
When the ignition is switched on, this
displays the following information au-
tomatically and directly:
- the time,
- the date,
- the outside temperature (if there is a risk of ice, you are warned by
a message).
Warning messages (e.g.: "Fuel lev-
el low") and vehicle function status
messages (e.g.: "Automatic switch-
ing on of the headlamps activated")
may appear temporarily. These can
be cleared by pressing the "ESC"
button.
General menu
When the RT4 GPS audio/telephone
is switched on, select the menu
which corresponds to the following
applications:
- the satellite navigation system,
- the guidance on the map,
- the trafi c information,
- the audio sources (radio, CD, Jukebox, ...),
- the telephone directories and functions,
- the coni guration of the screen and the setting of the parameters
of the vehicle's equipment,
- the displaying of a video,
- the vehicle diagnostics (warnings log and status of the functions).
Controls
From the RT4 GPS audio/telephone
control panel, to select one of the ap-
plications:

 press the "MENU" button to gain
access to the general menu ,

 turn the dial to move the selec-
tion,

 press the dial to coni rm the se-
lection,
or

 press the "ESC" button to aban-
don the operation in progress and
return to the previous display.
For further details concerning these
applications, refer to the RT4 part of
the "Audio and Telematics" section.

Page:   1-10 11-20 21-30 31-40 41-50 ... 50 next >