Peugeot 307 SW 2007.5 Owner's Guide

24
INSTRUMENTS, CONTROLS and DISPLAYS
When the needle is in zone A , the
temperature is correct.
When the needle is in zone B ,
the temperature is too high. The
central STOP warning light l ashes,
accompanied by an audible signal
and a message on the multifunction
display.

You must stop immediately.

Warning: wait for the engine to cool
before topping up the level.
The cooling system is pressurised.
In order to avoid any risk of scalding,
unscrew the cap two turns to allow
the pressure to drop.
When the pressure has dropped,
remove the cap and top up the level.
Contact a PEUGEOT dealer.
Coolant temperature indicator
When the engine is running, this
indicates the temperature of the oil.
The temperature is too high if the
maximum graduation is reached.

You must stop immediately.
Contact a PEUGEOT dealer.
Park
Automatic gearbox lever
positions indicator

Reverse

Neutral

Drive
Manual mode:
1st gear engaged

2nd gear engaged

3rd gear engaged

4th gear engaged
Engine oil temperature
indicator

5th gear *** engaged

6th gear *** engaged
*** According to model.

25
INSTRUMENTS, CONTROLS and DISPLAYS
In the event of under-revving or over-
revving, the gear selected l ashes for
a few seconds, then the actual gear
engaged is displayed. This comes on when the

"SPORT" programme on
the automatic gearbox is
selected.
This comes on when the

"SNOW" programme on
the automatic gearbox is
selected.
Automatic gearbox indicator
lights
"SNOW" indicator light This is displayed if a gear
is not engaged correctly
(selector between two posi-
tions).
"SPORT" indicator light
Invalid value during manual
operation
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).

Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on locking
and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section). Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since the last service.

Note: the distance remaining before
the next service may be weighted
by the time factor, depending on the
user’s driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.

Example: 4,800 miles/km remain
before the next service. For i ve sec-
onds after the ignition is switched on,
the display indicates:
INSTRUMENT PANEL
DISPLAY

26
INSTRUMENTS, CONTROLS and DISPLAYS
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance. Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder
re-set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" ,
release the button; the spanner
disappears.

Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least i ve
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The spanner l ashes for 5 seconds
after the ignition is switched on.

Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit. The display
indicates the total and trip distance.

Note: the spanner may also come on
if more than two years have elapsed
since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).

Example: 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and

the spanner remains lit .
It indicates that a service must
be carried out soon. The display
indicates the total and trip distance. Service indicator zero re-set

27
INSTRUMENTS, CONTROLS and DISPLAYS
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the but-
ton.
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service informa-
tion.
Oil level correct
Oil level gauge fault
Flashing of "OIL --"
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a
PEUGEOT dealer.

The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
Flashing of
"OIL" ,
linked with the ser-
vice warning light,
accompanied by
an audible signal
and a message on
the multifunction display, indicates a
lack of oil which could damage the
engine.
If the lack of oil is coni rmed by a
check using the dipstick, it is essential
that the level is topped up.
Lack of oil Dipstick
There are 2 marks on the
dipstick:
- never exceed level A,
- in position B, top up the level via the oil i ller
cap, using the type of oil
suited to your engine.

A = max.

B = min.
Trip recorder zero reset
button Lighting rheostat

25
INSTRUMENTS, CONTROLS and DISPLAYS
In the event of under-revving or over-
revving, the gear selected l ashes for
a few seconds, then the actual gear
engaged is displayed. This comes on when the

"SPORT" programme on
the automatic gearbox is
selected.
This comes on when the

"SNOW" programme on
the automatic gearbox is
selected.
Automatic gearbox indicator
lights
"SNOW" indicator light This is displayed if a gear
is not engaged correctly
(selector between two posi-
tions).
"SPORT" indicator light
Invalid value during manual
operation
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).

Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on locking
and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section). Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since the last service.

Note: the distance remaining before
the next service may be weighted
by the time factor, depending on the
user’s driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.

Example: 4,800 miles/km remain
before the next service. For i ve sec-
onds after the ignition is switched on,
the display indicates:
INSTRUMENT PANEL
DISPLAY

25
INSTRUMENTS, CONTROLS and DISPLAYS
In the event of under-revving or over-
revving, the gear selected l ashes for
a few seconds, then the actual gear
engaged is displayed. This comes on when the

"SPORT" programme on
the automatic gearbox is
selected.
This comes on when the

"SNOW" programme on
the automatic gearbox is
selected.
Automatic gearbox indicator
lights
"SNOW" indicator light This is displayed if a gear
is not engaged correctly
(selector between two posi-
tions).
"SPORT" indicator light
Invalid value during manual
operation
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).

Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on locking
and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section). Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since the last service.

Note: the distance remaining before
the next service may be weighted
by the time factor, depending on the
user’s driving habits.
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.

Example: 4,800 miles/km remain
before the next service. For i ve sec-
onds after the ignition is switched on,
the display indicates:
INSTRUMENT PANEL
DISPLAY

26
INSTRUMENTS, CONTROLS and DISPLAYS
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance. Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder
re-set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" ,
release the button; the spanner
disappears.

Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least i ve
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The spanner l ashes for 5 seconds
after the ignition is switched on.

Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit. The display
indicates the total and trip distance.

Note: the spanner may also come on
if more than two years have elapsed
since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).

Example: 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and

the spanner remains lit .
It indicates that a service must
be carried out soon. The display
indicates the total and trip distance. Service indicator zero re-set

26
INSTRUMENTS, CONTROLS and DISPLAYS
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance. Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder
re-set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" ,
release the button; the spanner
disappears.

Important: after this operation, if you
wish to disconnect the battery, lock
the vehicle and wait for at least i ve
minutes, otherwise the zero re-set
will not be registered.
The service is overdue.
The spanner l ashes for 5 seconds
after the ignition is switched on.

Example: the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the spanner remains lit. The display
indicates the total and trip distance.

Note: the spanner may also come on
if more than two years have elapsed
since the last service.
The distance remaining to the
next service is less than 500 miles
(1,000 km).

Example: 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and

the spanner remains lit .
It indicates that a service must
be carried out soon. The display
indicates the total and trip distance. Service indicator zero re-set

27
INSTRUMENTS, CONTROLS and DISPLAYS
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the but-
ton.
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service informa-
tion.
Oil level correct
Oil level gauge fault
Flashing of "OIL --"
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a
PEUGEOT dealer.

The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
Flashing of
"OIL" ,
linked with the ser-
vice warning light,
accompanied by
an audible signal
and a message on
the multifunction display, indicates a
lack of oil which could damage the
engine.
If the lack of oil is coni rmed by a
check using the dipstick, it is essential
that the level is topped up.
Lack of oil Dipstick
There are 2 marks on the
dipstick:
- never exceed level A,
- in position B, top up the level via the oil i ller
cap, using the type of oil
suited to your engine.

A = max.

B = min.
Trip recorder zero reset
button Lighting rheostat

28
INSTRUMENTS, CONTROLS and DISPLAYS
TRIP COMPUTER

 Press the button, located at the
end of the wipers stalk , to dis-
play the various items of trip com-
puter data in succession. The trip computer data is the
following:
System which provides current infor-
mation concerning the route travelled
(range, consumption, ...).

 Press the control for more than
two seconds to reset the distance
travelled, the average consump-
tion and the average speed to
zero.
Monochrome display A
Zero reset
Data displays - the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.
 The next press then returns you
to the normal display.