Peugeot 307 SW Dag 2007.5 Workshop Manual

COMFORT
49
Electric exterior mirrors
Adjustment

 Slide switch A to the right or to the
left to select the corresponding
mirror.

 Move knob B in all four directions
to adjust.

 Return switch A to the centre
position. Folding
- from inside:

 with the ignition on, pull switch

A rearwards.
- from outside:
 lock the vehicle using the re-
mote control or the key.
Unfolding
- from inside:
 with the ignition on, pull switch

A rearwards.
- from outside:
 unlock the vehicle using the re-
mote control or the key. The folding and unfolding of
the exterior mirrors can be
deactivated by a PEUGEOT
dealer.

Note: if the mirrors are folded using
switch A , they will not unfold when
the vehicle is unlocked using the
remote control or the key. Switch A
must be pulled again.
MIRRORS
The end of the driver's mir-
ror glass is aspherical (outer
zone marked by a dotted
line) in order to reduce the
"blind spot".
Furthermore, objects seen in the
driver and passenger mirrors are, in
reality, closer than they appear.
Therefore, this must be taken into
account in order to judge correctly
the distance of vehicles approaching
from behind.

COMFORT
50
This automatically and gradually
changes between the day and night
positions. To prevent dazzling, the
glass of the mirror darkens auto-
matically depending on the intensity
of the light from behind. It clears as
the light (headlamps of following ve-
hicles, sunlight) decreases, ensuring
maximum visibility. Manual interior mirror
The interior mirror has two positions:
- day (normal),
- night (anti-dazzle).
To change from one to the other,
push or pull the lever on the lower
edge of the mirror.
Operation
Switch on the ignition and press
switch
1 :
- Indicator light 2 lit (switch
pressed): automatic operation.
- Indicator light 2 off: automatic
system off. The mirror remains at
its most clear.
Special feature
To ensure maximum visibility during
manoeuvres, the mirror clears auto-
matically when reverse gear is en-
gaged. When the vehicle is stationary, un-
lock the steering wheel by pulling
handle A .
Adjust the height and depth of the
steering wheel.
Lock it by pushing handle A down
fully.
STEERING WHEEL HEIGHT
AND DEPTH ADJUSTMENT
Automatic day/night interior
mirror

COMFORT
50
This automatically and gradually
changes between the day and night
positions. To prevent dazzling, the
glass of the mirror darkens auto-
matically depending on the intensity
of the light from behind. It clears as
the light (headlamps of following ve-
hicles, sunlight) decreases, ensuring
maximum visibility. Manual interior mirror
The interior mirror has two positions:
- day (normal),
- night (anti-dazzle).
To change from one to the other,
push or pull the lever on the lower
edge of the mirror.
Operation
Switch on the ignition and press
switch
1 :
- Indicator light 2 lit (switch
pressed): automatic operation.
- Indicator light 2 off: automatic
system off. The mirror remains at
its most clear.
Special feature
To ensure maximum visibility during
manoeuvres, the mirror clears auto-
matically when reverse gear is en-
gaged. When the vehicle is stationary, un-
lock the steering wheel by pulling
handle A .
Adjust the height and depth of the
steering wheel.
Lock it by pushing handle A down
fully.
STEERING WHEEL HEIGHT
AND DEPTH ADJUSTMENT
Automatic day/night interior
mirror

COMFORT
51
FRONT SEATS
1. Forwards-backwards adjustment
Lift the control and slide the seat for-
wards or backwards.
2. Driver's or passenger's seat height adjustment
Pull the handle upwards or push it
downwards as many times as neces-
sary to obtain the required position.
3. Seat back angle adjustment
Push the handle towards the rear.
4. "Aircraft" type table
There is an "aircraft" type table, i t-
ted with a can holder, on the back of
each front seat.

COMFORT
52
5. Head restraint height and angle adjustment
To raise the head restraint, pull it up-
wards.
To remove the head restraint, press the
lug A and pull the head restraint up-
wards.
To put the head restraint back in posi-
tion, locate the stems of the head re-
straint in the holes taking care to keep
them in line with the seat back.
To lower the head restraint, press the
lug A and the head restraint at the
same time.
The head restraint has a frame with a
latch which prevents the head restraint
from lowering; this safety device pro-
vides protection in the event of an im-
pact. 8. Heated seats control
Never drive with the head re-
straints removed; they must
be in place and correctly
adjusted.
REAR HEAD RESTRAINTS
These have a high position for when
they are in use and a low position for
when they are stored.
The head restraints are also remov-
able.
To remove them, pull upwards as far
as the stop then press the lug (side
seat) or the two lugs (centre seat).
6. Armrests
These can be folded down and are
removable.
To remove them, press the button lo-
cated between the armrest and the
side of the seat and pull.
7. Storage drawers
There is a storage drawer under each
front seat * .
- To open it, lift it and pull.
- To take it out, open it to its full
extent, press the ends of the
slides and lift it, then remove it
completely.
- To put it back in place, with it fully closed, press on the top of the
drawer to secure it.
Under the front passenger seat, the
layout of the l oor allows for storage
of a i rst aid kit and a warning triangle
(small version).

The adjustment is correct when
the upper edge of the head
restraint is level with the top of
the head.
To adjust the angle of the head restraint,
tilt the lower part forwards or backwards.
Do not place heavy objects
in the drawers. With the engine running, press the
switch. The temperature is controlled
automatically.
Pressing the switch again stops op-
eration.

Note: the command for activation of
the heating of the seat(s) remains
memorised for two minutes after the
ignition has been switched off.
* According to model.

COMFORT
53
Exit from the 3rd row or folding
from the boot
Place the head restraint in the low
position.
Fold the seat back onto the cushion
using the strap B .

Note: you can lock the seat back in
this position (for removal) by press-
ing down on it.
Pull the strap C upwards to release
the rear feet.
Place the seat in the folded position.
Forwards-backwards
adjustment *
Lift the bar
A and slide the seat for-
wards or backwards.
* Except additional seat.
Seat back angle adjustment
Pull the strap B , at the front of the
seat on the right or on the left, then
adjust to the required angle.
Release the strap to lock.
To adjust the angle of the seat back
from the 3rd row or the boot, pull the
strap B at the rear of the seat.

Note: the additional seat can be
angled and folded by means of the
strap B at the rear of the seat on the
right or on the left. Access to the 3rd row
Place the head restraint in the low
position.
If necessary, push the seat back us-
ing bar
A .
Fold the seat back onto the cushion
using the strap B .

Note: you can lock the seat back
in this position (e.g. for removal) by
pressing down on it.
Pull the strap C upwards to release
the rear feet.
Place the seat in the "folded" position.
Folding a side seat
REAR SEATS

COMFORT
54
Place the head restraint in the low
position.
Fold the seat back onto the cushion
using the strap B .
You now have a small table with four
can holders, two pen holders and a
document holder. Folding the centre seat
Place the head restraint in the low
position.
Fold the seat back onto the cushion
using the strap
B .

Note: you can lock the seat back in
this position (for removal) by press-
ing down on it.
Pull the strap C upwards to release
the rear feet.
Place the seat in the folded position.

While driving, attach the retain-
ing strap (contained in the storage
pocket of one of the front seats) on
one side to the carrying handle F
and on the other side, to one of the
stems of a front head restraint. Place the head restraint in the low
position.
Pull the strap
B (at the rear of the
seat to the right or to the left) back-
wards then press on the seat back to
release it, while continuing to pull the
strap.
Fold the seat back onto the seat
cushion.

Note: you can lock the seat back in
this position (for removal) by press-
ing down on it.
Push the two levers D upwards to un-
lock the rear feet.
Place the seat in the folded position.

While driving, attach the retain-
ing strap (contained in the storage
pocket of the additional seat) on
one side to the carrying handle F
and on the other side, to the rear
armrest grab handle.
Centre seat table position
Folding an additional seat

COMFORT
Fold the corresponding seat.
Tilt the two red levers E under the
seat to release the front feet.
Lift it and carry it using the carrying
handle F .
In the 3rd row, position the i xing point
closers to obtain a l at boot l oor. Refitting a seat
In the 3rd row, i rst remove the l oor
i xing point closers using a thin
screwdriver.
Before positioning the 3rd row seats,
move those of the 2nd row forward if
necessary.

Check that nothing is obstructing
the l oor i xing points thus pre-
venting correct locking of the seat
feet.
Carry the seat using the carrying
handle F .
Position the front feet in the securing
points and lock them by means of the
two red levers E .
Locked
Pull the strap C upwards to check
that the rear feet are free.
Tilt the folded seat backwards. The rear feet lock automatically.

Check that the seat is locked cor-
rectly.
Lift the seat back, i rst releasing it by
pulling the strap B .
To lock the additional seats, press
the two levers D .
Only lock the seat back on
the cushion occasionally, to
avoid undue wear of the seat
covers.
Avoid placing luggage on folded
seats.
Never use the adjusting straps to re-
move, rei t or carry a seat, use the
carrying handle provided for this pur-
pose.
Free
Removing a seat

COMFORT
56
SEAT MODULARITY AND DIFFERENT CONFIGURATIONS
The design of your vehicle and of its seats offers multiple
seat coni gurations.
There are side seats which can be installed in the 2nd or
3rd row, on the right or on the left.
Once the centre seat has been removed from the 2nd row,
you can recentre the side seats for more comfort.
There is also a centre seat , i tted in the central position of
the 2nd row, which can also be installed in the left p osition
in the 3rd row.
In this case, you must use the 3rd row rear left seat belt
without passing it through the strap guide.
You can add up to two additional seats in the 3rd row, on
the right or on the left.
The various operations resulting in modii cation of
the existing coni guration must be carried out when
the vehicle is stationary (see "Seats" section). Examples of varied arrangements combining
comfort and practicality:
5 seats
4 seats with table position

COMFORT
5 seats with centre seat in the 3rd row
Transportation of long objects 4 seats with side seat in the 3rd row
Loading of a large volume