Peugeot 308 Dag 2007.5 Owner's Manual

11
i
i
139
Access to the spare wheel
The spare wheel is installed in the boot under the floor.
According to country, the spare wheel may be steel, alloy or of the "space sav-ing" type.
To gain access to it, refer to the para-graph "Access to the tools" on the previ-ous page.
Taking out the wheel
 Unscrew the yellow central bolt.
 Raise the spare wheel towards you from the rear.
 Take the wheel out of the boot.
Putting the wheel back in place
 Put the wheel back in its housing.
 Unscrew the yellow central bolt by a few turns then put it in place in the centre of the wheel.
 Tighten fully until the central bolt clicks to retain the wheel correctly.
 Put the box back in place in the cen-tre of the wheel and clip it.
 Put the polystyrene storage box back in place.

11
i
140
Removing the wheelList of operations
 Remove the chromed bolt cover from each of the bolts using the tool 3.
 Fit the anti-theft socket 4 on the wheelbrace 1 to unlock the anti-theft bolt.
 Unlock the other bolts using the wheelbrace 1 only.
 Place the jack 2 in contact with one of the two front A or rear B locations provided on the underframe, which-ever is closest to the wheel to be changed.
 Extend the jack 2 until its base plate is in contact with the ground. Ensure that the centreline of the jack base plate is directly below the location Aor B used.
 Raise the vehicle until there is suf-ficient space between the wheel and the ground to admit the spare (not punctured) wheel easily.
 Remove the bolts and store them in a clean place.
 Remove the wheel.

11
i
141
Fitting the wheelList of operations
 Put the wheel in place on the hub.
 Screw in the bolts by hand to the stop.
 Pre-tighten the anti-theft bolt using the wheelbrace 1 fitted with the anti-theft socket 4.
 Pre-tighten the other bolts using the wheelbrace 1 only.
 Lower the vehicle fully.
 Fold the jack 2 and detach it.
 Lock the anti-theft bolt using the wheelbrace 1 fitted with the anti-theft socket 4.
 Lock the other bolts using the wheel-brace 1 only.
 Refit the chromed bolt covers on each of the bolts.
 Store the tools in the box.

11
i
!
!
142
* According to country.
CHANGING A BULB
Procedure for replacing a faulty bulb with a new bulb without the use of tools.
Front lights
Model with halogen lights
1. Direction indicators(PY 21 W amber).
2. Dipped headlamps(H7-55 W).
3. Main beam headlamps(H1-55 W).
4. Daytime*/side lights(P 21/5 W).
5. Fog lamps (H8-35 W).
1. Direction indicators(PY 21 W SV silver).
2. Dipped/main beam headlamps (D1S-35 W).
3. Additional main beam headlamps (H1-55 W).
4. Daytime*/side lights(P 21/5 W).
5. Fog lamps(H8-35 W).
Model with xenon lights and directional headlamps

11
i
!
143
Changing main beam headlamp bulbs
 Remove the protective plastic cover by pulling on the tab.
 Disconnect the bulb connector.
 Compress the springs to release the bulb.
 Remove the bulb and change it.
To refit, carry out these operations inreverse order.
Changing daytime/side light bulbs
 Remove the protective plastic cover by pulling on the tab.
 Disconnect the bulb connector.
 Turn the bulb holder a quarter of a turn and extract it.
 Pull the bulb and change it.
To refit, carry out these operations inreverse order.
Changing direction indicator bulbs
 Turn the bulb holder a quarter of a turn and extract it.
 Pull the bulb and change it.
To refit, carry out these operations in re-verse order.
Changing dipped headlamp bulbs
 Remove the protective plastic cover by pulling on the tab.
 Disconnect the bulb connector.
 Compress the springs to release the bulb.
 Extract the bulb and change it.
To refit, carry out these operations inreverse order.

11
i
144
Changing integrated direction indicator side repeaters
 Insert a screwdriver towards the centre of the repeater between the repeater and the base of the mirror.
 Tilt the screwdriver to extract therepeater and remove it.
 Disconnect the repeater connector.
To refit, carry out these operations inreverse order.
Contact a PEUGEOT dealer to obtain replacement repeaters.
Changing fog lamp bulbs
 Turn the wheel fully towards the in-side for easy access to the flap.
 Open the access flap, located in the wheelarch.
 Disconnect the bulb holder connec-tor.
 Turn the bulb holder a quarter of a turn and extract it.
 Pull the bulb and change it.
To refit, carry out these operations in re-verse order.

11
i
145
Rear lights
1. Brake/side lights(P 21/5 W).
2. Side lights(P 21/5 W).
3. Fog lamp, left-hand side(P 21 W).
Reversing light, right-hand side (P 21 W).
4. Direction indicators(P 21 W).
Changing bulbs
These five bulbs are changed from out-side the boot:
 remove the two light fixing nuts,
 extract the light carefully from the outside,
 disconnect the light connector,
 press the four tabs and remove the bulb holder,
 turn the bulb a quarter of a turn and change it.
To refit, carry out these operations inreverse order.
 on the right-hand side; remove the access flap,
 on the left-hand side; turn the fixing bolt a quarter of a turn and remove the storage box cover,
 unclip the storage box,

11
146
Changing third brake light bulbs(4 bulbs W 5 W)
 Unclip the tailgate upper trim from left to right.
 Unscrew the two light fixing nuts A.
 Unclip the light's central pin.
 Extract the light from the outside.
 Disconnect the bulb holder connec-tor and the wash-wipe pipe.
 Unclip the bulb holder from the light by pressing on the two tabs B.
 Pull the bulb and change it.
To refit, carry out these operations inreverse order.
Do not apply force to the light when tightening the nuts.
Changing the number plate light bulbs (W 5 W)
 Insert a thin screwdriver into one of the outer holes of the lens.
 Push it outwards to unclip.
 Remove the lens.
 Pull the bulb and change it.

11
!
i
147
CHANGING A FUSE
Procedure for replacing a faulty fuse with a new fuse to rectify a failure of the corresponding function.
Access to the tools
The extraction pliers and the spare fus-es are installed on the back of the fascia fuse box cover.
To gain access to them:
 turn the screw a quarter of a turn to the left,
 unclip the cover by pulling at the top right,
 remove the cover completely,
 remove the pliers.
Changing a fuse
Before changing a fuse, the cause of the failure must be identified and recti-fied.
 Identify the faulty fuse by checking the condition of its filament.
 Use the special pliers to extract the fuse from its housing.
 Always replace the faulty fuse with a fuse of the same rating.
 Check the correspondence between the number etched on the box, the rating etched on the fuse and thetables below.
CorrectIncorrect

11
148
Fascia fuses
The fuse box is placed in the lower sec-tion of the fascia (left-hand side).
Access to the fuses
 refer to the paragraph "Access to the tools".
Fuse tables
Fuse N°RatingFunctions
G3630 ADriver and passenger heated seats.
G375 ATrailer fuse box.
G3830 ADriver’s seat memory unit.
G3930 ATrailer fuse box supply.
G4030 AHi-Fi amplifier.
Fuse N°RatingFunctions
F115 ARear wiper.
F2-Not used.
F35 AAir bags and pretensioners control unit.
F410 A
Clutch pedal and dual-function brake switches, electrochromatic interior mirror, air conditioning, steering wheel angle sensor, automatic gearbox, switching and protection unit.
F530 AFront one-touch electric windows, folding mirrors supply, glass panoramic roof shutter.
F630 ARear one-touch electric windows.
F75 AFront and rear courtesy lights, map reading lights, rear reading lights, sun visor lighting, glove box lighting.