ignition PEUGEOT 4007 2012 Service Manual

7
DRIVING

Programming



)
Press button 1
.

)
Set the programmed speed by ac-
celerating to the required speed,
then press button 2 "COAST SET"
.

CRUISE CONTROL CRUISE C

The controls of this system are grouped
together on the steering wheel.


1.
"ON/OFF"
button: activation/deacti-
vation of the cruise control mode.

2.
"COAST SET"
button: storing of a
driving speed and decreasing of the
cruising speed.

3.
"ACC RES"
button: increasing of
the cruising speed and recalling of
the stored speed.

4.
"CANCEL"
button: switching off of
the cruise control.
When you press button 1
, the "CRUISE"

indicator comes on in the instrument
panel.


Steering mounted controls
Display on the instrument panel

The cruise control cannot, in any
circumstances, take the place of
the need to comply with speed
limits or of the vigilance and re-
sponsibility of the driver.
System which automatically maintains the
vehicle speed at the value programmed
by the driver, without any action on the
accelerator pedal.

The cruise control is switched on

manually: the vehicle speed must be
25 mph (40 km/h) minimum and sec-
ond gear must be engaged in the case
of a manual gearbox.

The cruise control is switched off
man-
ually, by an action on the brake or clutch
pedal or if the ASC system is triggered.

The programmed speed can be exceeded
temporarily by pressing the accelerator
pedal.
To return to the programmed speed,
simply release the accelerator pedal.

Switching off the ignition cancels any
programmed speed value.

8
CHECKS
CHECKING LEVELS
Brake fluid level
To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.

Oil level

The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
The check is carried out either
when the ignition is switched on using
the oil level indicator on the instrument
panel, or using the dipstick.
It is normal to top up the engine oil be-
tween services. The manufacturer recom-
mends that the oil level be checked, and
topped up if necessary, every 3 000 miles
(5 000 km). The brake fl uid level should be
between the "MAX" and "MIN"
marks.
If it is not, check the brake pad
wear.

Changing the brake fl uid
Refer to the servicing booklet for details
of the interval for this operation.


Coolant level

The coolant level must be mea-
sured when the engine is cold
and should be between the
"LOW" and "FULL" marks.
When the engine is warm, the
temperature of the coolant is regulated
by the fan. This can operate with the ig-
nition off.
On vehicles which are fi tted with a
particle emission fi lter, the fan may
operate after the vehicle has been
switched off, even if the engine is
cold.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work.

Screenwash and headlamp
wash * fluid

Check the fl uid level regularly,
using the gauge.

*
According to country.
Changing the engine oil
Refer to the servicing booklet for details
of the interval for this operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.

Oil specifi cation
The oil must correspond to your engine
and conform to the manufacturer's
recommendations.

Fluid specifi cation
The brake fl uid must conform to the
manufacturer's recommendations and
fulfi l the DOT4 standards.

Changing the coolant fl uid
Refer to the servicing booklet for details
of the interval for this operation.

Fluid specifi cation
The coolant must conform to the manu-
facturer's recommendations.


Fluid specifi cation
This fl uid must conform to the manufac-
turer's recommendations for optimum
cleaning.



Power steering fluid level

Check the fl uid level with the engine at
idle.
Check that the power steering fl uid
level is always between the "MAX" and
"MIN" marks and top up if necessary.

Fluid specifi cation
This fl uid must conform to the manufac-
turer's recommendations.
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
If a level drops signifi cantly, have the
corresponding system checked by a
PEUGEOT dealer or a qualifi ed work-
shop.
When working under the bonnet, take
care as certain areas of the engine may
be extremely hot (risk of burns).

9
PRACTICAL INFORMATION

Parking the vehicle
Immobilise the vehicle where it
does not block traffi c: if possible,
park the vehicle on level, stable
and non-slippery ground.
Apply the parking brake, switch
off the ignition and engage fi rst
gear to lock the wheels.
If necessary, place a chock un-
der the wheel diagonally oppo-
site the wheel to be changed.
Never go underneath a vehi-
cle raised using a jack; use a
stand.
















Removing a wheel

List of operations


)
If your vehicle is equipped with se-
curity wheel bolts (equipment avail-
able as an accessory) fi t the security
socket 5 on the wheelbrace 1
to
slacken the security bolt.

)
Slacken the other bolts using the
wheelbrace 1
only.

)
Place the jack 2
in contact with one
of the two front A
or rear B
locations
provided on the underbody, which-
ever is closest to the wheel to be
changed.

)
Extend the jack 2
until its base plate
is in contact with the ground. Ensure
that the centreline of the jack base
plate is directly below the location A

or B
used.

)
Raise the vehicle until there is suffi -
cient space between the wheel and
the ground to admit the spare (not
punctured) wheel easily.

)
Remove the bolts and store them in
a clean place.

)
Remove the wheel.

9
PRACTICAL INFORMATION

Dashboard fuses

The fuseboxes are placed in the lower
dashboard behind the enclosed storage
compartment (left-hand side).

Access to the fuses


)
Open the cover A
,

)
Pull it towards you to extract it,

)
Change the fuse (refer to the cor-
responding paragraph).

Fuse N°



Rating



Functions




1*



30 A

Heating.


2



15 A

Brake lamps, third brake lamp, built-in systems
interface.


3



10 A

Rear foglamps.


4



30 A

Windscreen wipers and screenwash.


5



10 A

Diagnostic socket.


6



20 A

Central locking, door mirrors.


7



15 A

Audio equipment, telematics, multifunction screen,
Bluetooth system.


8



7.5 A

Remote control key, air conditioning control unit,
instrument panel, switch panel, steering mounted
controls.


9



15 A

Multifunction screen, instrument panel.


10



15 A

Built-in systems interface.


11



15 A

Rear wiper.


12



7.5 A

Instrument panel, 4 wheel drive control unit,
air conditioning control panel, ABS control
unit, multifunction screen, automatic headlamp
adjustment, heated seats, airbag control unit,
steering wheel angle sensor, sunroof, rear screen
demisting, remote control.


13



-

Not used.


14



10 A

Ignition switch.


15



20 A

Sunroof.


16



10 A

Door mirrors, audio equipment, telematics.

9
PRACTICAL INFORMATION

Engine compartment fuses

The fusebox is placed in the engine compartment near the
battery (left-hand side).

Access to the fuses


)
Open the bonnet (refer to the "Access" section),

)
Press on the hook A
to release the catch,

)
Remove the cover completely,

)
Change the fuse (refer to the corresponding paragraph),

)
When you have fi nished, close the cover carefully to en-
sure sealing of the fusebox.

Fuse N°



Rating



Functions




1



15 A

Front foglamps.


2



7 A

Engine ECU 2.4 litre 16 V


3



20 A

CVT automatic gearbox ECU, CVT
automatic gearbox relay


4



10 A

Horn.


5



7.5 A

Alternator 2.4 litre 16V


6



20 A

Headlamp wash.


7



10 A

Air conditioning.


8



15 A

Engine ECU 2.4 litre 16 V


9



-

Not used.


10



15 A

Demisting, wipers.


11



-

Not used.


12



-

Not used.


13



-

Not used.


14



10 A

Left-hand main beam headlamp.


15



10 A

Right-hand main beam headlamp.


16



20 A



Left-hand dipped beam headlamp (xenon).



17



20 A


Right-hand dipped beam headlamp (xenon).



18



10 A


Left-hand dipped beam headlamp, manual
and automatic headlamp adjustment.


19



10 A

Right-hand dipped beam headlamp.


20



-

Not used.


21



10 A

Ignition coils

9
PRACTICAL INFORMATION
The batteries contain harmful
substances such as sulphuric
acid and lead. They must be
disposed of in accordance with
regulations and must not, in any
circumstances, be discarded
with household waste.
Take used remote control bat-
teries and vehicle batteries to a
special collection point.

Charging the battery using a
battery charger


)
Disconnect the battery from the ve-
hicle.

)
Remove the battery and place it in a
ventilated area.

)
Remove the top-up caps and top up
the level with distilled water if nec-
essary.

)
Connect the battery to the charger
observing the instructions for use
provided by the manufacturer and
start charging.

)
Disconnect the battery from the
charger and let it to cool.

)
If necessary, top up the level with
distilled water.

)
Clean the top of the battery care-
fully.

)
Put the top-up caps back in place.

)
Check that the terminals and con-
nectors are clean. If they are cov-
ered with sulphate (whitish or
greenish deposit), remove them
and clean them.

)
Reconnect the battery starting with
the positive terminal (+). It is advisable to disconnect the
battery if the vehicle is to be left un-
used for more than one month.
Do not disconnect the terminals
while the engine is running.
Do not charge the batteries with-
out disconnecting the terminals
fi rst.
Avoid prolonged contact of the
electrolyte with the skin.
Most of these fl uids are harmful
to health and very corrosive. When charging the battery, it is
normal to observe an increase
in temperature and bubbling of
the electrolyte.
Before disconnecting the battery
Wait 2 minutes after switching off the igni-
tion before disconnecting the battery.
Close the windows, the sunroof, the
doors and the tailgate before discon-
necting the battery.

Following reconnection of the
battery
Following reconnection of the battery,
switch on the ignition and wait 1 minute
before starting to permit initialisation of
the electronic systems. However, if slight
diffi culties are encountered following this
operation, contact a PEUGEOT dealer or
a qualifi ed workshop.
Referring to the corresponding section,
you must yourself reinitialise:


- the one-touch electric windows,

- the sunroof,

- the satellite navigation system.

11
AUDIO EQUIPMENT and TELEMATICS
STEERING MOUNTED CONTROLS STEERING MOUNTED CONTRO



1.
On/Off and selection of

radio or
CD mode


2.
Volume decrease


3.
Volume increase


4.
Search for a higher radio
frequency/Next track/Fast
forwards play


5.

Search for a lower radio frequency/
Previous track/Fast backwards play


They can be used when the ignition
switch is in the "ON" or "ACC" position.
Switching on

Press button 1
for more than two seconds.

The last source selected before switching
off comes back into operation.

Selecting the source
Press button 1
.
The source changes in the following order:
FM1/FM2/FM3/MW/LW/CD/FM1...
Searching in radio mode
Press button 4
or 5
to search for a higher
or lower radio frequency respectively.
While a track is being played,
press button 5
once to return to
the beginning of this track.

Adjusting the volume

Press and hold button 2
or 3
to decrease or increase the volume respectively.
Switching off

Press button 1
for more than two seconds.


Searching in CD mode
Press button 4
or 5
to select the next or
previous track on the CD respectively.
Press and hold button 4
or 5
for fast for-
wards or fast backwards playing of the
current track of the CD respectively.

11
AUDIO EQUIPMENT and TELEMATICS
GENERAL FUNCTIONS

Switching on

Press the "PWR" button.
The last source selected be-
fore switching off resumes
operation.
The audio equipment func-
tions can be used when the ignition
switch is in the "ON" or "ACC" position.


Adjusting the volume

Turn the "VOL" dial respec-
tively to the left to decrease
the volume or to the right to
increase it.


Switching off

Press the "PWR" button again.


Setting the audio modes

Press the "SOUND" but-
ton several times; the audio
modes change in the following
order:
SUB PUNCH/TYPE/FIELD/
BASS/MID/TREBLE/FAD-
ER/BALANCE/OFF.


Quick access mode

To access the personalised sound func-
tions quickly, press and hold this button,
then turn it to reach the personalised
sound setting of your choice.
Release the button to store the setting.


"Hold" mode

If you press this button for more than
2 econds in the audio setting mode, the
system switches to "Hold" mode. The
audio mode selected will be retained
until you press this button again for
more than 2 seconds.

Selecting the musical ambience
"TYPE"
Turn the "SOUND" dial; the
musical ambiences change
in the following order:
CLASSIC/JAZZ/POP/
ROCK/HIP-HOP.
Once the ambience has been selected,
press the "SOUND" button to confi rm.
"CLASSIC": optimises the acoustics to
obtain perfect equalisation of the sound
for classical music.
"JAZZ": optimises the acoustics to ob-
tain an ambient sound with specifi c
modulations in the bass, mid tone and
treble for jazz.
"POP": optimises the acoustics to ob-
tain clear vocals and modulation of the
bass and treble for pop music.
"ROCK": optimises the acoustics to ob-
tain a sound in harmony with the rhythm
which places the emphasis on the mid
tone for rock music.
"HIP-HOP": optimises the acoustics to
obtain a powerful sound and accentua-
tion of the bass for hip-hop music.
If the "TYPE" is changed, the
sound cuts out briefl y. The audio setting mode is deacti-
vated when the radio is operated
or a CD is played or after approxi-
mately 10 seconds without any
action.

11
AUDIO EQUIPMENT and TELEMATICS

Matching your Bluetooth®
telephone
The system can register up to 7 Bluetooth®
compatible mobile telephones.
The telephone which has the highest
level of priority is connected automati-
cally.
It is absolutely essential that the vehicle
is parked in a safe place with the parking
brake applied.
1 - Press the SPEAK button.
7 - Say a 4-digit number which will
be recorded as the matching
code. 12 - After the audible signal, allo-
cate a name to the telephone
by saying the name of your
choice.
13 - The system says "Allocate an order
of priority between 1 and 7. One is
the highest level of priority".
If the system does not detect the
Bluetooth
® compatible mobile
telephone, the matching proc-
ess stops accompanied by an
audible signal.
If you select a level of priority
which has already been allo-
cated to another telephone, the
system asks you if you wish to
replace this level of priority. Remember this matching code as
you must enter it in the telephone
in one of the following steps of
the matching procedure.
9 - The system says "Start the match-
ing procedure on the telephone.
Consult the instructions in the tel-
ephone manual".
2 - Say "Confi gure".
3 - Say "Matching options".
5 - Say "Match a telephone". 8 -
The system confi rms the validity of
the number spoken, answer "Yes".
Say "No" to return to step 7.

10 - Consult your mobile tele-
phone's user manual and
enter the matching code
recorded in step 7 in the
telephone. 14 - Say a number between 1 and
7 to establish the level of pri-
ority of the mobile telephone.
15 - The system says and confi rms the
<name of the telephone> and the
<number> of its priority.
16 - Answer <Yes> or say <No>
to return to step 13.
17 -
The systems says "Matching com-
plete" then emits an audible signal and
deactivates the voice recognition
.
4 - The system says "Do you wish to
match a telephone, delete a tele-
phone or obtain the list of matched
telephones?".
6 - The systems says "Please say the
4 digits of a matching code". If the code is incorrect, the system
locks. To clear the code:


- check that the telephone's
voice recognition is not acti-
vated,

- with the ignition on and the
audio system active, press
the HANG UP button for
2 seconds, 3 times in suc-
cession.
11 - When it detects a Bluetooth
® com-
patible mobile telephone, the system
says "Please say the name of the
telephone after the bleep".

11
AUDIO EQUIPMENT and TELEMATICS















Making a telephone call using a name in the phone book, receiving a call


Using a name in the system's phone
book
The name must be recorded in the sys-
tem's phone book. 8 - Answer "Yes" or say "No" to
return to step 4.

Redialling the last number
Receiving a call
The telephone ring is transmitted on the
speaker by the front passenger's seat.
If an audio source (CD, radio, ...) is in
operation when the call is received, it is
placed on mute and only the incoming
call is heard.
When the ignition switch is in the ACC
or ON position, the audio system is ac-
tivated automatically if an incoming call
is received, even if it was originally off.
1 - Press the PICK UP button.
At the end of the call, the audio system
returns to its previous status.
1 - Press the SPEAK button.
2 - Say "Call".
4 - Say the name of the person
that you wish to call.
6 - Say the location corresponding
to the number that you wish to
call. 1 - Press the SPEAK button.
2 - Say "Redial". 3 - The system says "Name please".
5 - If several telephone numbers have
been recorded for this person, the
system says "Do you wish to call
<name> {home}, {work}, {mobile} or
{pager]?" .
7 - The system request confi rmation of
the name. 9 - The system says "Call to <name> at
<location>" and makes the call.