key battery PEUGEOT 4008 2012 Owners Manual

32
Instruments and controls
Screen 1Screen 2CauseSolution - ActionObservations
Warning messages (ignition at "OFF")
You have forgotten to switch off the
vehicle lighting. Switch off the vehicle lighting by
placing the control at OFF. There is an intermittent audible signal.
The alarm has been tri
ggered.
The batter
y for the Keyless Entryand Starting system is flat. Replace the battery (see "Changingthe batteries").
The electronic key that you have on
your person is not recognised. Check that you have the correct electronic key. If the message persists, contact a
PEUGEOT dealer.
The electronic ke
y is still in the
vehicle and
you have tried to lock
the doors or boot from the outside. Ensure that
you have the electronic
key on your person before lockingthe vehicle.
One of the doors or the boot is notproperly closed when locking the
vehicle from the outside.
Close the door or the boot, then lock
the vehicle.

1
35
Instruments and controls
Screen 1Screen 2CauseSolution - ActionObservations

Warning messages (ignition at "ON")
Fault with the electric power steering. Stop the vehicle, wait few moments
then start the engine again. If the message remains after
restarting, contact a PEUGEOT
dealer or a qualified workshop.
The batter
y for the "Keyless Entry and Starting" system is flat. Replace the battery (see "Changingthe batteries").
The electronic ke
y that you have onyour person is not recognised. Check that you have the correctelectronic key. If the message persists, contact a
PEUGEOT dealer.
The electronic ke
y is still in the
vehicle and you have tried to lock
the doors or boot from the outside. Ensure that
you have the electronickey on your person before lockingthe vehicle.
One of the doors or the boot is not properly closed when locking the
vehicle from the outside. Close the door or the boot, then lock
the vehicle.
Fault with the "Ke
yless Entry andStarting" system. Contact a PEUGEOT dealer.

67
2
Access





Emergency procedure with the Keyless Entry and Starting
system
Unlocking
) Turn the key towards the front in thedriver's door lock to unlock the vehicle.



Emergency unlocking/locking

using the integral key
The integral key is used to lock and unlock the
vehicle when the electronic key cannot operate:


- cell batter
y flat, vehicle battery discharged
or disconnected, ...

- vehicle located in an area with stron
gelectro-magnetic signals.)Pull and hold button 1 , to extract the integral key 2.


Locking
)
Turn the key towards the rear in the driver's door lock to lock the vehicle.



The emergency key allows you to lock or unlock the driver's door only. To lock or unlock the other doors, usethe interior controls (see "Locking / unlocking from inside").

68
Access
With the Keyless Entry and Starting system, message appears in the instrument panel when replacement of the battery is needed.
Changing the batteries
Do not throw the remote controlbatteries away, they contain metals which are harmful to the environment. Take them to an approved collectionpoint.
Remote control key
Battery ref.: CR1620 / 3 volts.


Electronic key

Battery ref.: CR2032 / 3 volt.
)Unclip the cover using a small screwdriver at the cutout. )Lift off the cover. )Remove the flat battery from its location. )Fit the new battery into its location observing the original direction of fitment.
)Clip the cover onto the casing.

73
2
Access
For all work on the alarm system, contact a PEUGEOT dealer or a qualified workshop.






Alarm * System which protects and provides a deterrent against theft and break-ins. It provides the following types of monitoring:




- perimeter

The system checks for any opening of the vehicle.
The alarm is triggered if anyone tries to open adoor, the boot, the bonnet...


- volumetric

The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compar tment or moves inside the vehicle.

- tilt

The system checks for any change in theattitude of the vehicle.
The alarm is triggered if the vehicle is lifted,moved or knocked.


Self-protection function

The system checks for the putting out of service of its components.
The alarm is triggered if the battery, the centralcontrol or the siren wiring are put out of service
or damaged.
Locking the vehicle with full
alarm system
Activation
)
Switch off the ignition (OFF mode if your
vehicle has the Keyless Entry and Star ting system).) Remove the key from the ignition switch,
if your vehicle does not have the "Keyless
Entry and Starting" system.) Leave the vehicle, and close all the doorsand the bonnet. )
Press the locking button on the remote control or one of the door or boot buttons
if your vehicle has the "Keyless Entry and Starting" system.
Deactivation

Do one of the the following to deactivate thealarm:)
Press the unlocking button on the remotecontrol or one of the door or boot buttonsif your vehicle has the "Keyless Entry andStarting" system.
)
Switch on the ignition (ON mode if your
vehicle has the "Keyless Entry andStarting" system). ) Open a door or the boot while the system is being activated.
The alarm system is deactivated: the indicator
lamp A
goes off.
The alarm is bein
g activated: the indicator
lamp A flashes rapidly accompanied byan intermittent audible signal for about
20 seconds.

Once the 20 seconds have expired, the
system is active . The audible signal stops and
the indicator lamp in the button flashes slowly.

*
According to equipment.

106
Driving








Starting - stopping the engine with the key
- Position 1: LOCKThe steering is locked.
- Position 2: ACCThe accessories (radio, 12 V socket...) can be used. - Position 3: ONIgnition on.
- P
osition 4: STARTStarting the engine.
Ignition switch


If you use the accessories for aprolonged period (with the key in position 2 (ACC)), you risk dischargingthe battery. Starting your vehicle will then no longer be possible. Be aware. See the "Automatic power cut-off toaccessories" section.

Key in ignition
A buzzer sounds on opening the driver'sdoor, if the key has been left in the ignition.
)
Inser t the key in the ignition switch.)
Turn the key to position 2 (ACC)
and unlock the steering column, by turning
wheel slightly. ) Press and hold the brake pedal.)
Fully depress the clutch pedal (vehicles fitted with a manual gearbox). )
Put the gear lever into neutral (vehicles fitted with a manual gearbox), or in position P(vehicles fitted with a CVT
gearbox). ) Operate the star ter by turning the key to
position 4 (START).) Once the engine is running, release the key.
The key returns automatically to
position 3 (ON).

Starting using the key
Stopping
)Immobilise the vehicle. )Put the gear lever into neutral (vehiclesfitted with a manual gearbox), or inposition P
(vehicles fitted with a CVT gearbox).)While pressing the key, turn it to position 1 (LOCK).)Remove the key from the ignition switch.)Lock the steering.


Do not attach any heavy objects to the key as this could weigh down on it whenin the ignition switch and cause a fault.
For Diesel vehicles, when the engineis cold wait with the ignition switchin position 3 (ON)
until the preheater warning lamp goes off, before turningthe key to position 4 (START)
. The warning lamp does not come on when the engine is hot.

107
4
Driving
vehicle
With the electronic key inside the vehicle ; eachpress on the " STA R T/STOP " button, with no
action on the pedals, changes the vehicle's mode :
)First press (ACC mode), the button's
warning lamp comes on in orange.
The accessories (radio, 12V socket...) can be used.)Second press (ON mode), the button's
warning lamp comes on in green.
Switching on the ignition.)Third press (OFF mode), the warning lamp
in the button goes off.
If you use the accessories for aprolonged period with the ignition switch in position 2 (ACC), you risk dischargingthe battery. Starting your vehicle will then no longer be possible. Take care.See the "Automatic power cut-off to accessories" section.













Starting - stopping the engine with the Keyless Entry
and Starting system
If the warning lamp flashes orange,contact a PEUGEOT dealer or aqualified workshop as soon as possible.
)Press and release the " START/STOP" button.
)
With the electronic key inside the vehicle,
depress the clutch pedal fully on vehicles
with a manual gearbox or press the brake pedal on vehicles with a CVT gearbox.

Starting using the
electronic key

For vehicles fitted with a manual gearbox
, put
the gear lever in neutral.
For vehicles fitted with a CVT gearbox, put thegear lever in P.P

117
4
Driving

Emergency release

If the battery is discharged or if the gear lever
locking mechanism is damaged, it is possible
for the gear lever to be locked in position P,Peven when you press the brake pedal firmly. However, i
f you have to move the vehicle, release the gear lever using the followingprocedure: ) Apply the parking brake. )
Switch off the engine if necessary. )
Remove the cap A, using a flat screwdriver covered with a cloth. )
Press the brake pedal firmly. )
Put the ignition switch into position ACC(ACC mode, if you vehicle has the Keyless
Entry and Star ting system).) Inser t the screwdriver into the aper ture. )
While pushing the screwdriver downwards,
move the gear lever to position N.
You must contact a PEUGEOT dealer or a qualified workshop to have thesystem checked .

119
4
Driving








Stop & Start (Auto Stop & Go) function


Operation


Going into engine STOP mode
The "AS &G "
warning lamp comes on in
the instrument panel or the instrument panel screen and the engine goes intostandby after a few seconds:


- with a manual
gearbox
, with the vehicle stationary and your foot on the brake, whenyou put the gear lever into neutral andrelease the clutch pedal.

Never refuel with the engine in STOPmode; you must switch off the ignition with the key or the START/STOP button.
When the engine is stopped automatically, the operation of certainvehicle systems, such as for example,braking, power steering... are modified. Take care.


Special cases: STOP mode notavailable
STOP mode is not invoked when:


- the driver's seat belt is not fastened,

- the bonnet is open,

- the vehicle has not exceeded 3 mph (5 km/h) since the last engine start,

- the vehicle has restarted less than10 seconds ago,

- the engine is needed to maintain acomfor table temperature in the passenger compartment,

- demisting is active,

- some special conditions (battery charge, engine temperature, braking assistance,
ambient temperature...) where the engine isneeded to assure control of a system.

- th
e "AS&G"warning lamp is
flashing in the instrument panel.
This operation is perfectl
y normal.

The Stop & Star t (Auto Stop & Go) function puts the engine temporarily into standby during stops in the traffic (red lights, traffic jams, or other...). Theengine restarts automatically as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Star t (Auto Stop & Go) function reduces fuel consumption and exhaust emissions as well as the noise level whenstationary.

121
4
Driving
The system is reactivated automatically at every new star t using the key or the STA R T/STOP button.

Reactivation

Press the "AS&G OFF"switch again.
The s
ystem is active again; this is confirmed by
the "AS &G O FF "
warning lamp going off in the
instrument panel or instrument panel screen.
Operating fault
In the event of a malfunction with the system,
the "AS&G OFF"warning lamp flashes in theinstrument panel or instrument panel screen,and the system no longer operates.
have it checked by a PEUGEOT dealer or a qualified workshop.
This system requires a specific battery with a special specification and technology (reference numbersavailable from a PEUGEOT dealer or aqualified workshop).
Fitting a battery not listed by
PEU
GEOT introduces the risk of malfunction of
the system.

Maintenance

The "Auto Stop & Go" system makes use of advanced technology. All work on this type of battery must be doneonly by a PEUGEOT dealer or aqualified workshop.
In the event o
f a fault in STOP mode, the
vehicle may stall. The following warning lampscome on in the instrument panel or instrumentpanel screen:
It is then necessar
y to switch off the ignition,
then restart the engine using the key or theSTA R T/STOP button.