lock PEUGEOT 4008 2014 User Guide
Page 35 of 368
1
33
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
Fault with the "Keyless Entry and
Starting" system. Contact a PEUGEOT dealer.
Fault with the electronic anti-theft
system. Switch off the ignition, then start
the engine. If the problem persists, contact a
PEUGEOT dealer.
The electronic key is not detected. Insert the electronic key into the
housing located in the glove box. Remember to remove the electronic
key from the housing after starting
the vehicle.
The electronic key has not been
removed from the housing in the
glove box. Remove the electronic key from the
housing in the glove box.
The steering column is locked. Switch the ignition on and turn the
steering wheel slightly to unlock the
steering column.
The engine is off but the gear lever
is not in position P
. Place the gear lever in position P
. Only for vehicles fitted with a "CVT"
gearbox.
Page 36 of 368
34
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
The steering column has not locked
after opening the driver's door. Lock the steering column by turning
the steering wheel slightly before
leaving the vehicle.
Fault with the electrical system. Contact a PEUGEOT dealer or
a qualified workshop.
Page 37 of 368
1
35
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
Warning messages (ignition at "ON")
Fault with the electric power
steering. Stop the vehicle, wait few moments
then start the engine again. If the message remains after
restarting, contact a PEUGEOT
dealer or a qualified workshop.
The battery for the "Keyless Entry
and Starting" system is flat. Replace the battery (see "Changing
the batteries").
The electronic key that you have on
your person is not recognised. Check that you have the correct
electronic key. If the message persists, contact a
PEUGEOT dealer.
The electronic key is still in the
vehicle and you have tried to lock
the doors or boot from the outside. Ensure that you have the electronic
key on your person before locking
the vehicle.
One of the doors or the boot is not
properly closed when locking the
vehicle from the outside. Close the door or the boot, then
lock the vehicle.
Fault with the "Keyless Entry and
Starting" system. Contact a PEUGEOT dealer.
Page 38 of 368
36
Monitoring
Screen 1
Screen 2
Cause
Solution - Action
Observations
The brake fluid level is too low. Top up using a brake fluid listed by
PEUGEOT. If the problem persists, contact a
PEUGEOT dealer or a qualified
workshop.
Fault with the braking system. You must stop as soon as it is safe
to do so. Have the system checked by a
PEUGEOT dealer or a qualified
workshop.
Fault with the anti-lock braking
system (ABS). Contact a PEUGEOT dealer or a
qualified workshop. The vehicle retains conventional
braking without assistance but you
are advised to stop.
One of the doors or the boot is not
properly closed. Close the door or the boot. The opening in question is identified
in the screen.
The bonnet is not properly closed. Close the bonnet.
Fault with the electronic anti-theft
system. Switch off the ignition then start the
engine again. If the problem persists, contact a
PEUGEOT dealer.
The driver's door is open and the
ignition is still on. Switch off the ignition before leaving
the vehicle.
Page 43 of 368
1
41
Monitoring
Screen 1
Screen 2
System
Observations
Information messages (ignition at "ON")
2WD two wheel drive
system
Flashes for a few moments when the "2WD" (2 wheel drive) mode is selected using
the transmission mode selector, for 4 wheel drive versions.
4WD four wheel drive
system
Flashes for a few moments when the "4WD" (4 wheel drive) mode is selected using
the transmission mode selector, for 4 wheel drive versions.
4WD LOCK four wheel
drive system
Flashes for a few moments when the "LOCK" (4 wheel drive) mode is selected using
the transmission mode selector, for 4 wheel drive versions.
Active stability control
(ASC)
Flashes when the stability control system (ASC) is operating.
Page 56 of 368
54
Monitoring
Audio-CD system screen
Associated with the Audio- CD system, this
screen can display the following information:
- the time,
- audio system information.
(see the "Audio equipment and telematics"
section).
Setting the time
Selecting the adjustment mode
The digital clock can be set in automatic
mode
or in manual mode
.
Manual mode
This mode permits manual setting of the time
using the audio system buttons.
It can also be used when the "Automatic mode"
displays an inaccurate time, when the local
RDS stations are broadcasting from a different
time zone.
Automatic mode
This mode permits automatic setting of the
local time using the signal from RDS stations.
The symbol "CT"
appears in the screen.
Page 57 of 368
1
55
Monitoring
If no action is carried out within
10 seconds, the selection menu closes
automatically. To select the mode:
)
Press the " PWR/VOL
" button to switch on
the audio system.
)
Press the MENU
button.
)
Press the SEL
knob to scroll through the
menus and select " RDS setting - CT ON -
CT OFF
" (clock time).
)
Turn the SEL
knob to the left or to the right
to select "CT OFF"
(manual mode)
or "CT ON"
(automatic mode).
)
Press the SEL
knob to confirm.
The digital clock does not display
seconds.
The time setting is lost if the battery is
disconnected.
Manual adjustment
)
Press the PWR/VOL
button to switch on
the audio system.
)
Press the MENU
button.
)
Press the SEL
knob to run scroll through
the menus and select " Time Setting
Adjust
".
)
Turn the SEL
knob to select " ON
" for
access to time setting.
)
Press the SEL
knob to confirm.
)
Turn the SEL
knob to adjust the time.
)
Press the SEL
knob to confirm.
Page 59 of 368
1
57
Monitoring
Display format
You can the display format for the date and
time:
)
Press the MENU
button.
)
Press " Setting
".
)
Press " System Setting
".
)
Press " Time Setting
".
)
Press " Time Display Settings
".
Permanent display
Once the data and time are set, you can
choose to have them always displayed in the
screen. To do this:
)
Press the MENU
button.
)
Press " Setting
".
)
Press " Clock Screen
".
You and then select the format for the display
of the date and time (" Date / Time Format
")
and activate automatic adjustment of the time
(" Clock Time
"). The date and time are displayed.
Simply touch the screen again to return to the
original display.
)
Press " Time Adjustment
".
)
Use the virtual arrows in the screen to
adjust the date and time.
)
Press " Set
" to conform or " Back
" to cancel
and return to the previous screen.
Page 61 of 368
1
59
Monitoring
System screen
Once in the " Tu n i n g …
" menu, select " System
"
to modify the time zone, the units, or the
display language (English, Dutch, Swedish,
French, Portuguese, Italian, German, Spanish,
Nor wegian, Flemish or Danish) and adjust
other settings.
"Settings" menu
Press the S
ETTINGS
button on the control
panel to open the menu.
Uses a soft clean cloth to clean the
screen.
Do not use pointed objects on the touch
screen.
Do not touch the screen with wet hands.
For reasons of safety, the driver
should only carry out operations that
require close attention with the vehicle
stationary .
In addition, some functions are not
accessible when driving.
For more information on these menus,
refer to the "Audio equipment and
telematics" section.
Setting the time
The digital clock is set automatically
.
This mode enables the system to set the local
time automatically using the signal from the
RDS stations.
)
On the control panel, press the SETTINGS
button for access to settings.
Page 64 of 368
62
Access
System which permits central unlocking or locking of the vehicle using the door lock or remotely. It is also used for the guide-me-home lighting and
starting the engine, as well as providing protection against theft.
Remote control key
Unfolding the key
)
First press this button to unfold the key.
Unlocking the vehicle
Complete unlocking using the
remote control
)
Press the open padlock to unlock
the vehicle.
Unlocking using the key
)
Turn the key to the front in the driver's door
lock to unlock it.
Unlocking is confirmed by the interior
lighting which comes on for around
15 seconds and the direction indicators
which flash twice
.
According to version, the door mirrors
unfold at the same time.