ignition PEUGEOT 4008 2014 Owner's Guide

88
Comfort







Electric folding /
unfolding

From the outside:



)
by locking or unlocking the vehicle,
using the remote control or the locking /
unlocking buttons (for vehicles fitted with
the "Keyless Entry and Starting" system).

If you have folded the mirrors using the
control C
, you must use this control to
unfold them, other wise the mirrors will
not be lock in place correctly.
The mirrors can also be folded
manually.

From inside:



- with the ignition switch in the "ON" or
"ACC" position, by pressing the control C
,

- with the ignition switch in the "LOCK"
position, by pressing control C, within
30 seconds.

96
Comfort

Personalisation of the
Exterior air intake / Interior air
recirculation function
This function is controlled automatically.
However, you can deactivate its automatic
control if you wish to change the air intake
mode at any time.


Changing the status

Press the Air intake / Interior air recirculation
button for at least 10 seconds.
When the status changes from active to
inactive, three bleeps are heard and the
indicator lamp flashes three times.
When the status changes from inactive to
active, two bleeps are heard and the indicator
lamp flashes three times.


Automatic control active

If the air distribution adjustment dial and the air
flow adjustment dial are placed in the "AUTO"
position, the Air intake / Interior air recirculation
function is also controlled automatically.


Automatic control inactive

Even if the air distribution adjustment dial and
the air flow adjustment dial are placed in the
"AUTO" position, the Air intake / Interior air
recirculation function is no longer controlled
automatically.
The settings are retained, even after switching
off the ignition.


4. Intake of exterior air /
Recirculation of interior air
This function insulates the passenger
compartment from exterior odours and smoke.


)
Press button 4
to select the air
intake mode.
When the indicator lamp on button 4
is off, the
exterior air intake function is on.
When the indicator lamp on button 4
is on, the
intake of exterior air is off and the system is in
air recirculation mode.
Do not drive for long periods in interior
air recirculation mode, except in truly
exceptional atmospheric conditions.

103
3
Comfort





Front armrest

Pull the right-hand lever to open the storage
compartment lid, which serves as an armrest.
To close, fold down the lid until it locks. Pull the left-hand lever to open the lid.
To close, fold down the lid until it locks.
This storage compartment may contain up to
3 accessory sockets.
This operates when the ignition switch is in the
"LOCK", "ACC" or "ON" position.
Open the cover of the front armrest to gain
access to the socket.

Upper storage compartment
Lower storage compartment


Check that the electrical equipment
operates on 12 V and that its maximum
electrical power is 120 W.
The prolonged use of electrical
equipment without running the engine
may discharge the battery.







12 V socket
(120 W max)

108
Driving








Starting - stopping the engine with the key



- Position 1: LOCK

The steering is locked.

- Position 2: ACC

The accessories (radio, 12 V socket...) can
be used.

- Position 3: ON

Ignition on.

- Position 4: START

Starting the engine.


Ignition switch


If you use the accessories for a
prolonged period (with the key in
position 2 (ACC)
), you risk discharging
the battery. Starting your vehicle will
then no longer be possible. Be aware
.
See the "Automatic power cut-off to
accessories" section.








Key in ignition

A buzzer sounds on opening the
driver's door, if the key has been left in
the ignition.

)
Insert the key in the ignition switch.

)
Turn the key to position 2 (ACC)
and
unlock the steering column, by turning
wheel slightly.

)
Press and hold the brake pedal.

)
Fully depress the clutch pedal (vehicles
fitted with a manual gearbox).

)
Put the gear lever into neutral (vehicles
fitted with a manual gearbox), or in
position P
(vehicles fitted with a CVT
gearbox).

)
Operate the starter by turning the key to
position 4 (START)
.

)
Once the engine is running, release the key.
The key returns automatically to
position 3 (ON)
.


Starting using the key
Stopping



)
Immobilise the vehicle.

)
Put the gear lever into neutral (vehicles
fitted with a manual gearbox), or in
position P
(vehicles fitted with a CVT
gearbox).

)
While pressing the key, turn it to position 1
(LOCK)
.

)
Remove the key from the ignition switch.

)
Lock the steering.

Do not attach any heavy objects to the
key as this could weigh down on it when
in the ignition switch and cause a fault.


For Diesel vehicles, when the engine
is cold wait with the ignition switch
in position 3 (ON)
until the preheater
warning lamp goes off, before turning
the key to position 4 (START)
.
The warning lamp does not come on
when the engine is hot.

Switching off the engine leads to a loss
of braking assistance.

109
4
Driving

Changing the mode of the
vehicle
With the electronic key inside the vehicle; each
press on the " START/STOP
" button, with no
action on the pedals, changes the vehicle's
mode:


)
First press (ACC mode), the button's
warning lamp comes on in orange.
The accessories (radio, 12V socket...) can
be used.

)
Second press (ON mode), the button's
warning lamp comes on in green.
Switching on the ignition.

)
Third press (OFF mode), the warning lamp
in the button goes off.
If you use the accessories for a
prolonged period with the ignition
switch in position 2 (ACC)
, you risk
discharging the battery. Starting your
vehicle will then no longer be possible.
Ta k e c a r e
.
See the "Automatic power cut-off to
accessories" section.













Starting - stopping the engine with the Keyless Entry
and Starting system

If the warning lamp flashes orange,
contact a PEUGEOT dealer or a
qualified workshop as soon as possible.

)
Press and release the " START/
STOP
" button.

)
With the electronic key inside the vehicle,
depress the clutch pedal fully on vehicles
with a manual gearbox or press the brake
pedal on vehicles with a CVT gearbox.

Starting using the
electronic key
For vehicles fitted with a manual gearbox , put
the gear lever in neutral.
For vehicles fitted with a CVT gearbox , put the
gear lever in P
.

110
Driving

For Diesel vehicles, when
the engine is cold starting
does not take place until the
pre-heater warning lamp has
gone off.
If one of the starting conditions is not
met, a reminder message appears in
the instrument panel screen. In some
circumstances, it is necessary to
turn the steering wheel slightly while
pressing the " START/STOP
" button
to assist unlocking of the steering;
a message warns you when this is
needed.
The presence of the electronic key
in the defined zone is essential. For
reasons of safety, do not leave this area
when the engine is running.


Switching off using the
electronic key

If the vehicle is not immobilised, the
engine will not stop.

This message is displayed
when the driver's door is
opened and the vehicle is not
in "OFF" mode.


)
Press the " START/STOP
" button again to
change to "OFF" mode.



)
Immobilise the vehicle.

)
Place the gear lever in neutral for vehicles
fitted with a manual gearbox , or on P
for
vehicles fitted with a CVT gearbox .

)
With the electronic key inside the vehicle,
press the " START/STOP
" button.
The engine stops.
The steering locks when a door is opened or on
locking the vehicle.
Each attempt at starting takes around
15 seconds. If the engine does not start, press
the " START/STOP
" button once more to try
again.


The presence of the electronic key in
the vehicle is essential for switching on
the ignition and starting only. Once the
engine has started, make sure that the
electronic key remains with the vehicle
until the end of the journey: other wise
you would not be able to lock the
vehicle.


Switching off the engine leads to a loss
of braking assistance.

112
Driving











Anti-theft protection


Electronic engine immobiliser

The keys contain an electronic chip which has
a secret code. When the ignition is switched
on, this code must be recognised in order for
starting to be possible.
This electronic engine immobiliser locks the
engine management system a few minutes
after the ignition is switched off and prevents
starting of the engine by anyone who does not
have the key.
In the event of a malfunction, you are informed
by a message in the instrument panel screen.
In this case, your vehicle does not start; contact
a PEUGEOT dealer as soon as possible.



Applying



)
Pull the parking brake lever fully up to
immobilise your vehicle.







Parking brake


Releasing



)
Pull the parking brake lever up gently,
press the release button A
then lower the
lever fully.
When the vehicle is being driven, if the parking
brake is still on or has not been fully released,
a message appears in the screen.

When parking on a slope, direct your
wheels against the kerb, apply the
parking brake, engage a gear or place
the gear lever in position P
for vehicles
fitted with a CVT gearbox, and switch
off the ignition ("OFF" mode).

118Driving

Manual gear changing

In the automated mode, you can take over
control temporarily at any time using the
steering mounted controls.
The use of these controls permits manual
selection of the gears in situations which
require a faster change down than that offered
in automated mode (arrival at a roundabout,
exit from a car park with a steep gradient,
over taking...).
The gearbox engages the gear requested if
the engine speed permits it. The gear engaged
appears.
To return to the automated mode, do one of the
following:


- press the back of the "+/OFF"
steering
mounted control 3
for approximately
2 seconds,

- move the gear lever quickly towards
position +/-
and then return it to position D
,

- stop the vehicle.




Stopping the vehicle
Operating fault

With the ignition on, if the message
"Slow down"
or "Service required"
appears
in the instrument panel screen, this indicates a
gearbox malfunction.
When a message is displayed, carry out the
following operations:


- slow down and stop your vehicle in a safe
place,

- place the lever in position P
and let the
engine run,

- open the bonnet to allow the engine to
cool.
If the message disappears for a long period,
you can set off again.
If the message remains displayed or appears
frequently, contact a PEUGEOT dealer or a
qualified workshop without delay. Before switching off the engine, you must place
the gear lever in position P
.
You must apply the parking brake to immobilise
the vehicle.

119
4
Driving

Emergency release

If the battery is discharged or if the gear lever
locking mechanism is damaged, it is possible
for the gear lever to be locked in position P
,
even when you press the brake pedal firmly. However, if you have to move the vehicle,
release the gear lever using the following
procedure:


)
Apply the parking brake.

)
Switch off the engine if necessary.

)
Remove the cap A
, using a flat screwdriver
covered with a cloth.

)
Press the brake pedal firmly.

)
Put the ignition switch into position ACC
(ACC mode, if you vehicle has the Keyless
Entry and Starting system).

)
Insert the screwdriver into the aperture.

)
While pushing the screwdriver downwards,
move the gear lever to position N
.

You must contact a PEUGEOT dealer
or a qualified workshop to have the
system checked
.

121
4
Driving








Stop & Start (Auto Stop & Go) function


Operation


Going into engine STOP mode

The "AS &G"
warning lamp comes on in
the instrument panel or the instrument
panel screen and the engine goes into
standby after a few seconds:


- with a manual gearbox
, with the vehicle
stationary and your foot on the brake, when
you put the gear lever into neutral and
release the clutch pedal.


Never refuel with the engine in STOP
mode; you must switch off the ignition
with the key or the START/STOP
button.
When the engine is stopped
automatically, the operation of certain
vehicle systems, such as for example,
braking, power steering... are modified.
Ta k e c a r e
.


Special cases: STOP mode not
available
STOP mode is not invoked when:


- the driver's seat belt is not fastened,

- the bonnet is open,

- the vehicle has not exceeded 3 mph
(5 km/h) since the last engine start,

- the vehicle has restarted less than
10 seconds ago,

- the engine is needed to maintain a
comfortable temperature in the passenger
compartment,

- demisting is active,

- some special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.

- the "AS &G"
warning lamp is
flashing in the instrument panel.

This operation is per fectly normal.


The Stop & Start (Auto Stop & Go) function puts the engine temporarily into standby during stops in the traffic (red lights, traffic jams, or other...).
The engine restarts automatically as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Start (Auto Stop & Go) function reduces fuel consumption and exhaust emissions as well as the noise level when
stationary.