lock PEUGEOT 4008 2014 Workshop Manual

149
6
Safety

When the vehicle is moving

If this warning lamp comes
on continuously it indicates a
malfunction of the anti-lock braking
system which could result in a loss of
control of the vehicle on braking.
The two warning lamps comes on at the
same time and the two warnings are
displayed alternately in the instrument
panel screen.
When replacing wheels (tyres and
rims), ensure that they conform to the
manufacturer's recommendations.
The vehicle retains normal braking.
Drive carefully at moderate speed and contact
a PEUGEOT dealer or qualified workshop as
soon as possible. If these two warning lamps come on, linked
with the warnings on the instrument panel
screen, they indicate a malfunction of the
electronic brake force distribution which could
result in a loss of control of the vehicle on
braking.

You must stop as soon as it is safe to do so.

Contact a PEUGEOT dealer or a qualified
workshop.

155
6
Safety





The driver must ensure that passengers use
the seat belts correctly and that they are all
restrained securely before setting off.
Wherever you are seated in the vehicle,
always fasten your seat belt, even for short
journeys.
Do not interchange the seat belt buckles as
they will not fulfil their role fully.
The seat belts are fitted with an inertia reel
permitting automatic adjustment of the
length of the strap to your size. The seat belt
is stowed automatically when not in use.
Before and after use, ensure that the seat
belt is reeled in correctly.
The lower part of the strap must be
positioned as low as possible on the pelvis.
The upper part must be positioned in the
hollow of the shoulder.
The inertia reels are fitted with an automatic
locking device which comes into operation in
the event of a collision, emergency braking
or if the vehicle rolls over. You can release
the device by pulling firmly on the strap and
releasing it so that it reels in slightly.
Recommendations for children

Use a suitable child seat if the passenger is
less than 12 years old or shorter than one
and a half metres.
Never use the same seat belt to secure more
than one person.
Never allow a child to travel on your lap. In order to be effective, a seat belt must:


- be tightened as close to the body as
possible,

- be pulled in front of you with a smooth
movement, checking that it does not
twist,

- be used to restrain only one person,

- not bear any trace of cuts or fraying,

- not be converted or modified to avoid
affecting its per formance.


In the event of an impact


Depending on the nature and
seriousness of the impact
, the
pretensioning device may be deployed
before and independently of the airbags.
Deployment of the pretensioners is
accompanied by a slight discharge of
harmless smoke and a noise, due to the
activation of the pyrotechnic cartridge
incorporated in the system.
In all cases, the airbag warning lamp comes on.
Following an impact, have the seat belts
system checked, and if necessary replaced,
by a PEUGEOT dealer or a qualified
workshop.
In accordance with current safety
regulations, for all repairs on your vehicle,
go to a qualified workshop with the skills
and equipment needed, which a PEUGEOT
dealer is able to provide.
Have your seat belts checked regularly by a
PEUGEOT dealer or a qualified workshop,
particularly if the straps show signs of
damage.
Clean the seat belt straps with soapy
water or a textile cleaning product, sold by
PEUGEOT dealers.
After folding or moving a seat or rear bench
seat, ensure that the seat belt is positioned
and reeled in correctly.

175
6
Safety
The incorrect installation of a child seat in a
vehicle compromises the child's protection in
the event of an accident.
Remember to fasten the seat belts or the
child seat harnesses keeping the slack
in
relation to the child's body to a minimum
,
even for short journeys.
For optimum installation of the "for wards
facing" child seat, ensure that the back of
the child seat is in contact with the back of
the vehicle's seat and that the head restraint
does not cause any discomfort.
If the head restraint has to be removed,
ensure that it is stored or attached securely
to prevent it from being thrown around the
vehicle in the event of sharp braking.











Advice on child seats


Installing a booster cushion

The chest part of the seat belt must be
positioned on the child's shoulder without
touching the neck.
Ensure that the lap part of the seat belt
passes correctly over the child's thighs.
PEUGEOT recommends the use of a booster
seat which has a back, fitted with a seat belt
guide at shoulder level.
As a safety precaution, do not leave:


- one or more children alone and
unsuper vised in a vehicle,

- a child or an animal in a vehicle which
is exposed to the sun, with the windows
closed,

- the keys within reach of children inside
the vehicle.


Children at the front

The legislation on carrying a child on the
front passenger seat is specific to each
country. Refer to the legislation in force in
your country.
Deactivate the passenger's airbag when a
"rear wards facing" child seat is installed on
the front seat. Other wise, the child would risk
being seriously injured or killed if the airbag
were to inflate.
To prevent accidental opening of the doors,
use the "Child lock".
Take care not to open the rear windows by
more than one third.
To protect young children from the rays of
the sun, fit side blinds on the rear windows.

176
Safety







Child lock

Mechanical system to prevent opening of the rear doors using their interior controls.
The control is located on the edge of each rear door.


Child lock on



)
Move the control A
towards position 1
.



Child lock off



)
Move the control A
towards position 2
.

183
7
Practical information
















Removing a wheel


Parking the vehicle

Immobilise the vehicle where it does not
block traffic: if possible, park the vehicle
on level, stable and non-slippery
ground.
Apply the parking brake, switch off the
ignition and engage first gear to lock
the wheels.
If necessary, place a chock under the
wheel diagonally opposite the wheel to
be changed.
Never go underneath a vehicle raised
using a jack; use a stand.


List of operations



)
If your vehicle is equipped with security
wheel bolts (equipment available as an
accessory) fit the security socket 5
on the
wheelbrace 1
to slacken the security bolt.

)
Slacken the other bolts using the
wheelbrace 1
only.

194
Practical information




















Changing a fuse

The extraction tweezer and spare fuses are
fitted in the engine compartment fusebox.
To gain access to them:


)
Open the bonnet (refer to the "Checks"
section).

)
Unclip the and remove the cover.

)
Remove the tweezer.

)
Carefully close the cover to ensure correct
sealing of the fusebox.



Access to the tools

Before changing a fuse, the cause of the failure
must be identified and rectified.


)
Check that the switch is in the " LOCK
"
position or that the vehicle mode is " OFF
".

)
Identify the faulty fuse by checking the
condition of its filament.


)
Use the special tweezer to extract the fuse
from its location.

)
Always replace the faulty fuse with a fuse
of the same rating.

)
Check that the number etched on the box,
the rating etched on the top and the tables
below all agree.


Changing a fuse

Good Failed

PEUGEOT will not accept responsibility
for the cost incurred in repairing your
vehicle or for rectifying the malfunctions
resulting from the installation of
accessories not supplied and not
recommended by PEUGEOT and
not installed in accordance with its
instructions, in particular when the
consumption of all of the additional
equipment connected exceeds
10 milliamperes.

Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories in your
vehicle, contact a PEUGEOT dealer or
a qualified workshop.
The replacement of a fuse not
mentioned in the following tables may
cause a serious fault on your vehicle.
Contact a PEUGEOT dealer or a
qualified workshop.

195
7
Practical information

Dashboard fuses

The fusebox is located in the lower dashboard
(left-hand side).

Access to the fuses



)
Open the cover and remove it completely
by pulling it towards you.

Fuse N°



Rating



Functions




1
*

30 A

Cabin fan.


2



15 A

Brake lamps, third brake lamp.


3



10 A

Rear foglamps.


4



30 A

Windscreen wiper, screenwash.


6



20 A

Central locking, electric door mirrors.


7



15 A

Audio equipment, telematics, USB unit, Bluetooth system.


8



7.5 A

Remote control key, air conditioning control unit, instrument
panel, electric windows, rain and sunshine sensors, alarm,
switch panel, steering mounted controls.


9



15 A

Instrument panel and interior lighting.


10



15 A

Hazard warning lamps


11



15 A

Rear wiper.


12



7.5 A

Instrument panel, multifunction screen, parking sensors,
heated seats, heated rear screen, electric blind, automatic
headlamp adjustment.


13



15 A

Cigarette lighter, accessory socket.


15



20 A

Electric blind.


16



10 A

Door mirrors, audio equipment.

204
Practical information





Recovering the vehicle



Recover y of your vehicle


2 wheel drive (2WD) versions: towing
with the wheels on the ground



)
Put the gear lever into neutral (position N

for the CVT gearbox).

)
Unlock the steering by by turning the
ignition switch to the " ON
" position (or
to " ON
" mode for vehicle fitted with the
"Keyless Entry and Starting" system).

)
Release the parking brake.

)
Switch on the hazard warning lamps on
both vehicles.

)
Move off gently and travel slowly for a short
distance only.



General recommendations

Observe the legislation in force in your
country.
Ensure that the weight of the towing
vehicle is higher than that of the towed
vehicle.
The driver must remain at the wheel of
the towed vehicle and must have a valid
driving licence.
When towing a vehicle with all four
wheels on the ground, always use an
approved towing bar; rope and straps
are prohibited.
When towing a vehicle with the engine
off, there is no longer any power
assistance for braking or steering.
In the following cases, you must always
call on a professional recovery ser vice:


- vehicle broken down on a motor way
or fast road,

- 4 wheel drive vehicle,

- when it is not possible to put the
gearbox into neutral, unlock the
steering, or release the parking
brake,

- towing with only two wheels on the
ground,

- where there is no approved towing
bar available...

Towing with the wheels on the ground
is only possible on 2 wheel drive (2WD)
versions.

)
Fit the towing bar to the towing eye on the
chassis, located under the front bumper.

248

Consult your mobile telephone's user manual and enter
the pairing code recorded in step 7 in the telephone.





BLUETOOTH ®
TELEPHONE
WITH VOICE RECOGNITION

The system says " Start the
pairing
procedure on the telephone.
Consult the instructions in the telephone manual
".

If the code is incorrect, the system locks. To clear the code:


- check that the telephone's voice recognition is not activated,

- with the ignition on and the audio system active, press the END
CALL button for 2 seconds, 3 times in succession.


When it detects a Bluetooth
®
compatible mobile telephone, the
system says " Please say the name of the telephone after the
beep
".

After the audible signal, allocate a name to the telephone
by saying the name of your choice.
The system says " Allocate an order of priority between 1 and 7.
One is the highest level of priority
".

Give a number between 1 and 7 to establish the level of
priority of the mobile telephone.

The system says and confi rms the " name of the telephone
" and
the " number
" of its priority.

Answer " Ye s
".
Say " No
" to return to step 13.

The systems says " Pairing complete
" then emits an audible signal
and deactivates the voice recognition.
The services available depend on the network, the SIM card and the compatibility of the Bluetooth
®
telephone used. Check in your telephone user
manual and with your service provider for the services you have access to.

If the system does not detect the Bluetooth
®
compatible mobile
telephone, the matching process stops ands is accompanied by an
audible signal.
If you select a level of priority which has already been allocated to
another telephone, the system asks you if you wish to replace this
level of priority.

282
05





















Using the USB port


With the vehicle stationary, ignition
switch in the LOCK
position, connect a
suitable cable to the portable player.
The USB port is used to connect a portable device (MP3 player,
Apple
® player, ...). The fi les are sent from the player to your audio
system and heard through the vehicle's speakers.

Then connect the cable to the vehicle's
USB port.
Models supported:
- iPod touch ® : FW version 1.1.1 or later.
- iPod classic ® : FW version 1.0 or later.
- iPod 5 th generation ®
: FW version 1.2.2 or later.
- iPod nano 5 th generation ®
: FW version 1.2 or later.
- iPod nano 2 nd generation ®
: FW version 1.1.2 or later.
- Compatible USB mass storage device: 256 Mb capacity or
greater.

File formats: MP3, WMA, AAC, WAV.
Maximum number of levels (including root): 8.
Number of folders: 700.
Number of fi les: 65 535.

Do not connect the portable device directly to the USB port, use a
cable.
To disconnect the cable, the ignition switch must be in the LOCK

position.
Navigation in the fi le base is done via the portable device / iPod
®
.
Take care not to trap the cable when closing the armrest.


MUSIC