sensor Peugeot 406 2002.5 Owner's Manual

29-07-2002
SPECIAL FEATURES
170
THE ALARM SYSTEM
Setting and disarming the
alarm
Setting and deactivating the alarm
The alarm completes the security
equipment for your vehicle. It offers
two types of protection. exterior protection: when it is set,
the alarm sounds if a door, the
boot or the bonnet is opened;
interior protection: when it is set,
the alarm sounds if the sensors
detect a variation in the air move
ment inside the vehicle (break
ing of a window) or movement
inside the vehicle.
The alarm is also equipped with an
antitamper function.
The alarm is also equipped with an
antitamper function.
If an attempt is made to tamper with
the wires to the siren, control unit or
the battery, the alarm is triggered:
the siren sounds and the headlamps
come on. Setting the alarm
(interior and exterior protection)
Switch the ignition off and get out
of the vehicle.
Press the locking button of the remote
control key.
The doors lock.
The direction indicators light for two
seconds.
The red light on the switch flashes once
a second.
5 seconds later, exterior protection is set.
50 seconds later, interior protection is set.
Note:
when the alarm is triggered, the
siren sounds for thirty seconds. After
the thirty seconds it stops, but the
alarm remains set.
Warning
If, on setting the alarm, a door, the boot
or the bonnet are not closed correctly,
the siren sounds for a moment. If the
vehicle is closed correctly in the follow
ing 45 seconds, the alarm is set and
the direction indicators remain on for
two seconds. In all cases, the alarm is
set after 45 seconds. Disarming the alarm
(interior and exterior protection)
Press the unlocking button of the
remote control key.
The doors unlock.
The direction indicators flash for two
seconds.
The red warning light on the switch
goes out.
Note:
if the warning light continues
to flash after disarming the alarm, it
is a sign that the alarm has been trig
gered. The flashing will stop when
the ignition is switched on.

29-07-2002
AUTOMATIC SWITCHING ON
OF THE LIGHTS
Side lights and dipped beam head
lamps switch on automatically if the
light is poor, or during continuous
operation of the windscreen wipers.
They switch off as soon as the light
becomes bright enough or the wind
screen wipers stop.
This function is active when the vehi
cle is supplied to the customer.
To disarm or activate the function: Place the key in the accessories
position (1st notch),
 Press the end of the lights stalk
for more than two seconds.
Note: In foggy weather, the bright
ness sensor can detect sufficient
light. Because of this, the lights do
not come on automatically.
Do not cover the brightness sen
sor connected to the rain sensor,
located in the windscreen behind
the mirror. It is used for automatic
switching on of the lights. Operating check
Activation
Activation of this function is accom
panied by an audible signal and the
message
"Automatic lighting of
the headlamps activated" on the
multifunction display.
Note: Always operate the lighting
controls manually where this is pos
sible.
Disarming
Disarming of the function is accom
panied by an audible signal.
When driving, if this function is
switched off when the headlamps
would switch on in automatic mode,
the lights remain on.
It is however possible to disarm this
function and switch off the lights by:
manually switching off the lights using the lights stalk,
switching off the engine.
YOUR 406 IN DETAIL 123
If the brightness sensor does not
function correctly, the system acti
vates the function (the lights come
on).The driver is alerted by the flash
ing of the ''dipped beam'' warning
light on the instrument panel.
Contact a PEUGEOT dealer to have
the system checked.
Follow me Home
When there is a low level of bright
ness or at night, if you leave your
vehicle, the side lights and the
dipped beam lights may remain on
for approximately one minute.
To do this: place the lights stalk in the AUTO
position,
 place the key in the accessories
position (first notch),
 press the end of the lights stalk for
more than two seconds,
 place the lights stalk in the 0posi
tion,
 flash the headlamps,
 get out of the car and lock it.

29072002
Fuse N° RatingFunctions
11* 10ALeft hand main beam.
12* 10 A Right hand main beam.
13* 15 AHorn.
14 10 AFront and rear screen wash pump.
15* 30 A Ignition coil Windscreen wiper Oxygen sensor Oil pressure– Inj ection system.
16* 30A Air pump Oil temperature Oil level Brake lights operation Al ternator Water in diesel
detector Injection relay control.
17* 30APassenger's electric seat.
18 40A Heater blower Starter Windscreen wiper slow speed.
MAINTENANCE OF YOUR 406 45