engine Peugeot 407 2009 User Guide

1INSTRUMENTS and CONTROLS
25
This indicates an automatic
gearbox programme fault.
Automatic gearbox lever
position indicator lights
This indicates an automatic
gearbox malfunction.

4 or 6 speed automatic gearbox
"Park" indicator
lights
"Reverse" indicator
lights
"Neutral" indicator
lights
"Drive" indicator
lights
The letter S or the symbol  associat-
ed with the gate lever position indicator
lights, corresponds to the Sport or Snow
programme selected intentionally. These correspond to the manual con-
trol of the gearbox, four or six speed.
When the engine speed is too low or
too high in relation to the gear engaged,
the gear selected fl ashes for a few sec-
onds, then the actual gear is displayed,
the auto-adaptive programme having
taken control temporarily.
Engine oil temperature
indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone
C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. "Manual" indicator lights

1INSTRUMENTS and CONTROLS
26
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer’s servicing schedule. Service indicator zero reset
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the reset procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder
reset button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears .
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time the
ignition is switched on and for 5 seconds,
the distance and the spanner fl ash.

Example
: when the ignition is switched
on and for 5 seconds, the display
indicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal
operation and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last service.
The distance remaining may be weighted
by the time factor, depending on the
user’s driving habits.
Operation
As soon as the ignition is switched
on and for 5 seconds, the spanner
symbolising the service operations is
lit. The trip recorder display shows the
distance remaining (in round fi gures)
before the next service.

Example
: when switching on the
ignition and for 5 seconds, the dis-
play shows that 900 miles/km remain
before the next service is due.
After this operation, if you
wish to disconnect the battery,
lock the vehicle and wait for at
least fi ve minutes, otherwise
the zero reset will not be
registered.

1INSTRUMENTS and CONTROLS
27
Engine oil level indicator
When the ignition is switched on,
the engine oil level is indicated for
approximately 5 seconds, after the
service information. Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil reservoir
cap, using the type of oil
suited to your engine.

A = max.

B = min. Trip recorder zero reset
Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
If the lack of oil is confi rmed by
checking using the dipstick, it is impe-
rative that the level is topped up. Oil level gauge fault
(fl ashing segments)
Check the oil level using the dipstick.
If the level is correct, the fl ashing
indicates an engine oil level gauge
malfunction.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes. The total distance is displayed in
zone A of the display and the trip
distance in zone B .
Distance recorder
With the trip distance displayed, press
the button for a few seconds.

3COMFORT
36
AUTOMATIC AIR CONDITIONING (MONO ZONE)

Mono zone: this is the overall regula-
tion of the temperature, distribution and
fl ow in the passenger compartment.
Control by the Auto programme Automatic
programme -
comfort (1)
Press the "AUTO" button. The indicator
light comes on. The "AUTO" symbol is dis-
played on the multifunction display.
Depending on the level of comfort selected,
the system controls the air distribution, fl ow,
temperature and intake of air in order to
guarantee comfort and an adequate circu-
lation of air in the passenger compartment.
You do not have to make any adjustments.

 Press the right or left
arrow to change it.
Adjustment of the temperature (2)
When the engine is cold, to
prevent too great a distribution
of cold air, the ventilation will
only reach its optimum level
progressively.
The symbols and messages associat-
ed with the automatic air conditioning
controls appear on the multifunction
display.
The value indicated on the display cor-
responds to a level of comfort and not
to a temperature in degrees Celsius or
Fahrenheit, depending on the choice of
confi guration validated on the display.
A setting around the value 21 makes
it possible to obtain optimum comfort.
However, depending on your require-
ments, a setting between 18 and 24 is
usual.

3COMFORT
38
Intake of exterior
air/Recirculation of
interior air (6)
This function enables you to isolate
the passenger compartment from ex-
terior fumes and odours.

 Press button 6 several times to
set the air intake mode, the indica-
tor light which corresponds to the
mode set comes on at your prefe-
rence:
- intake of exterior air. Forced exterior air intake mode.
- recirculation of the air inside the passenger compartment.
The indicator light which corres- ponds to the mode set comes on.
Prolonged operation in interior
air recirculation mode may result
in the formation of condensation
and deterioration of the quality of
the interior air.
Do not drive in air recirculation mode for prolonged periods,
except in truly exceptional
atmospheric conditions.
The message associated with the control is displayed on the
multifunction display.

 Press button 6 to return to auto
matic control of the air intake. The
two indicator lights are switched off.

For your comfort, when the igni-
tion is switched off, the settings are
stored until it is switched on again. Rear screen
demisting (7)
The heated rear screen operates inde-
pendently of the air conditioning system.

 Press button 7 , with the engine
running, to demist the rear screen
and the mirrors. The indicator light
comes on.
Demisting is switched off automatically
to prevent an excessive consumption
of current and in relation to the exterior
temperature.
It may be stopped by pressing button 7
again or when the engine is switched off.
However, demisting resumes if the
engine is switched on again within
one minute.
Switch off the rear screen and exterior
mirrors demisting when you consider
this necessary as low current con-
sumption reduces fuel consumption.

3COMFORT
39
"AIR CON" menu Press the "MENU" but-
ton to gain access to
the general menu, then
confi rm.
The "General menu" appears on the
multifunction display.
Select the Air Conditioning icon using
the navigator buttons. The
"Air Conditioning" menu ap-
pears on the multifunction display as
the main display.
Deactivation of the air conditioning
(AC-OFF) Additional heating *
Vehicles which are fi tted with an HDI
engine may be equipped with auto-
matic additional heating to improve
your comfort.
When the engine is idling or when the
vehicle is stationary, a high-pitched
whistling noise and the emission of a
small amount of smoke and odour is
normal.
Deactivation may result in discomfort
(temperature, humidity, odour, con-
densation).
The symbol "AC OFF" is displayed on
the multifunction display.
There is a risk that the temperature
setting value may not be reached and
you risk having condensation on the
windows.
You can cancel the deactivation by
pressing the "AUTO" button on the air
conditioning control panel.
* According to country.

3COMFORT
AUTOMATIC AIR CONDITIONING (DUAL ZONE)

Dual zone: this is the differentiated
regulation of the temperature and air
distribution on the driver's side and the
front passenger side.
The driver and his front passenger
can each adjust the temperature and
the distribution of the air to suit their
requirements.
Control by the Auto programme Automatic
programme - driver
and passenger
comfort (1)
Press the "AUTO" button. The indicator
light comes on. The "AUTO" symbol is
displayed on the multifunction display.
Adjustment of the temperature
on the driver's side (2)
Adjustment of the temperature
on the passenger side (3)

 Press the up or down arrow to
change the temperature on the
driver's side 2 or passenger side 3 .
The value indicated on the display cor-
responds to a level of comfort and not
to a temperature in degrees Celsius or
Fahrenheit, depending on the choice of
confi guration validated on the display.
A setting around the value 21 makes
it possible to obtain optimum comfort.
However, depending on your require-
ments, a setting between 18 and 24
is usual.
When the engine is cold, to
prevent too great a distribution
of cold air, the ventilation will
only reach its optimum level
progressively.
The symbols and messages associated
with the automatic air conditioning
controls appear on the multifunction
display.
Depending on the level of comfort se-
lected, the system controls the air dis-
tribution, fl ow, temperature and intake
of air in order to guarantee comfort
and an adequate circulation of air in
the passenger compartment. You do
not have to make any adjustments.

3COMFORT
42
Front visibility
control (7)
In certain cases, the comfort pro-
gramme may not be suffi cient to de-
mist or de-ice the windows (humidity,
several passengers, ice).

 In this case, select the front vis-
ibility programme in order to clear
the windows quickly. The indicator
light comes on.
It controls the air conditioning, air fl ow
and intake and distributes the ventila-
tion to the windscreen and front side
windows.
The front visibility control symbol is
displayed on the multifunction display.
Once the inconvenience has been
eliminated, pressing button 1 returns
the system to the comfort setting. Intake of exterior
air/Recirculation of
interior air (8)
This function enables you to isolate
the passenger compartment from
exterior fumes and odours.

 Press button 8 several times to set
the air intake mode, the indicator
light which corresponds to the mode
set comes on at your preference:
- intake of exterior air. Forced exterior air intake mode.
- recirculation of the air inside the passenger compartment.
The indicator light which corresponds to the mode set
comes on. Prolonged operation
in interior air recirculation mode
may result in the formation of
condensation and deterioration
of the quality of the interior air.
Do not drive in air recirculation mode for prolonged periods,
except in truly exceptional
atmospheric conditions.
The message associated with the control is displayed on the
multifunction display.

 Press button 8 to return to auto-
matic control of the air intake. The
indicator lights are switched off.

For your comfort, when the igni-
tion is switched off, the settings are
stored until it is switched on again. Rear screen
demisting (9)
The heated rear screen operates inde-
pendently of the air conditioning system.

 Press button 9 , with the engine
running, to demist the rear screen
and the mirrors. The indicator light
comes on.
Demisting is switched off automatical-
ly to avoid an excessive consumption
of current and in relation to the exterior
temperature.
It may be stopped by pressing button 9
again or when the engine is switched off.
However, the demisting resumes if
the engine is switched on again within
one minute.
Switch off the rear screen and exterior
mirrors demisting when you consider
this necessary as low current con-
sumption reduces fuel consumption.

3COMFORT
43
Deactivation of the air conditioning
(A/C-OFF)
Deactivation or activation of the
simultaneous Left-Right control
Activation of this function permits the
transfer of the driver's confi guration to
the passenger.
Deactivation of this function permits a
return to the independent driver/pas-
senger settings.
Any manual action on button 4 or 6
cancels the simultaneous confi gura-
tion setting.
"AIR CON" menu
Press the "MENU" but-
ton to gain access to
the general menu, then
confi rm.
The "General menu" appears on the
multifunction display.
Select the Air Conditioning icon using
the navigator buttons.
The "Air Conditioning" menu ap-
pears on the multifunction display as
the main display.
Additional heating *
Vehicles which are fi tted with an HDI
engine may be equipped with auto-
matic additional heating to improve
your comfort.
When the engine is idling or when the
vehicle is stationary, a high-pitched
whistling noise and the emission of a
small amount of smoke and odour is
normal.
* According to country.
Deactivation may result in discomfort
(temperature, humidity, odour, con-
densation).
You can cancel the deactivation by
pressing the
"AUTO" button on the air
conditioning control panel.

4ACCESS
64
CHANGING THE REMOTE CONTROL BATTERY
Battery ref.: CR1620/3 volts.
To change the battery, unclip the casing
using a coin at the notch.
REPROGRAMMING THE REMOTE CONTROL

 Switch off the ignition.

 Switch the ignition on again.

 Press the remote control locking but-
ton immediately for a few seconds.

 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again.
If the remote control does not work
after the battery has been changed,
re-programme the remote control.
ELECTRONIC ENGINE IMMOBILISER
Electronic engine immobiliser
indicator light It is accompanied by a message on
the multi-function display.
Your vehicle will not start.
Consult a PEUGEOT dealer.
Do not discard the batteries,
they contain metals which are
harmful to the environment.
Take them to an approved col-
lection point. This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic chip
which has a special code. When the
ignition is switched on, the code must be
recognised for starting to be possible.

If the system does not function correctly, the following indicator light comes on: If the keys are lost
Visit a PEUGEOT dealer with the ve-
hicle's V5 registration certifi cate and
your personal identifi cation.
The PEUGEOT network will be able to re-
trieve the key code and the transponder
code to order a replacement key.

Make a careful note of the
number on each key. The
key number is coded on the
label attached to the key.

If the keys are lost, a PEUGEOT
dealer can rapidly supply you with
new keys.

The high frequency remote control
is a sensitive system; do not ope-
rate it while it is in your pocket as
there is a possibility that it may un-
lock your vehicle, without you being
aware of it.

The remote control does not ope-
rate when the key is in the ignition,
even when the ignition is switched
off, except for reprogramming.

Do not operate the deadlocking
function if there is anyone inside
the vehicle.