fog light Peugeot 407 2009 Owner's Manual

Page 10 of 250

FAMILIARISATION
Lights
Ring B Windscreen wipers with intermittent
wipe

2 Fast wipe.

1 Normal wipe.

I Intermittent wipe.

0 Park.



Single wipe.
Wipers
Rear wiper (SW)
Front fog lamps (one press).
Rear fog lamps (two presses). Park.
Intermittent wipe.
Wash-wipe.

 73

 76
 77
Automatic windscreen wipers

2 Fast wipe.

1 Normal wipe.

AUTO Automatic wipe.

0 Park.



Single wipe.
Ring A
Lights off .
Automatic switching on of the
lights.
Side lights .
Dipped/Main beam headlamps. Windscreen wipers with intermittent
and automatic wipe

2 Fast wipe.

1 Normal wipe.

I Intermittent wipe.

0 Park.

 76
Automatic wipe then single
wipe.

Page 16 of 250

1INSTRUMENTS and CONTROLS
19

1. Coolant temperature indicator dial.

2. Lights on indicators:
dipped headlamps.
main beam headlamps.
front fog lamps.
rear fog lamps.

3. Rev counter dial.

4. Warning lights:
seat belts not fastened
in the front.
fuel level.
left direction indicator.

5. Fuel level indicator dial.
PETROL-DIESEL MANUAL AND AUTOMATIC GEARBOX INSTRUMENT PANELS

10. CHECK and trip recorder zero
reset and service display button.

11. Instrument panel display:
Total distance recorder.
Trip recorder.
Automatic gearbox lever position
indicator.
Cruise control/speed limiter
reference value.
Service indicator.
Direction advice (navigation)
CHECK (vehicle autotest).
Trip computer information
displays.
Warning and status displays.

12. Instrument panel lighting rheostat.

6. Warning lights:
handbrake applied or brake fl uid
level or electronic brake force
distribution fault.
right direction indicator.

7. Speedometer dial.

8. Warning lights:
emission control system.
anti-lock braking system (ABS).
passenger air bag disarmed.
pre-heat (diesel engine starting).

9. Engine oil temperature indicator
dial.

Page 82 of 250

5
73
LIGHTS
Lights on
With the ignition off, on opening the
driver's door a buzzer sounds to indi-
cate that you have left your lights on
although you are leaving the vehicle.

 Switch the lights off. Direction indicators
(fl ashers)
Dipped/main beam change

 Pull the stalk fully towards you. Front and rear fog lamps
(ring B)

 Turn ring B forwards to switch on
and rearwards to switch off. The
status is confi rmed by the light on
the instrument panel.
Front fog lamps (one press)

Left: downwards. The
direction arrow indicator
light fl ashes on the instru-
ment panel.

Right: upwards. The
direction arrow indicator
light fl ashes on the instru-
ment panel.
If you forget to return the
direction indicator to its normal
position, the volume of the
audible signal will increase, if
you are driving at a speed greater than
40 mph (60 km/h) or if the control is
maintained for more than 20 seconds.
These operate with the side lights and
the dipped or main beam headlamps.
Rear fog lamps (two presses)
These operate when the front fog
lamps are already on.
Front and rear lights (ring A)


Turn ring A to the position required.
Automatic switching on of
the lights,
Lights off,
Side lights,
Dipped/main beam
headlamps.

Model without AUTO lighting

Model with AUTO lighting

Page 83 of 250

5
74
Automatic switching on of the lights
The dipped beam headlamps switch
on automatically if the light is poor and
when the windscreen wipers operate
continuously. They switch off when
the light is bright enough or the wind-
screen wipers stop.
Warning: in foggy weather or in snow,
the brightness sensor can detect suf-
fi cient light. The lights will not come on
automatically.
If necessary, you must switch the
dipped headlamps on manually. Activation Manual "Follow-me-home"
lighting
When you leave your vehicle, the side
lights and dipped headlamps can be
left on for a few seconds.
When the function is activated,
the indicator light comes on on the
5-dial instrument panel display.
To disarm or activate the
function, pass via the
" P e r s o n a l i s a t i o n - c o n -
fi guration" menu on your
multifunction display.
For safety reasons, activation/
deactivation of the "Automatic
switching on of the lights"
function via the menu must be
carried out when stationary. To deactivate or activate the
"Automatic follow-me-home
lighting" function, pass via the

"Personalisation-confi gu-
ration" menu on your multi-
function screen.
The duration of timing can be
set via the "Personalisation-
confi guration" menu of your
multifunction display.
Automatic "Follow-me-home"
lighting
When you leave your vehicle
with the
automatic switching on of the lights
activated, the side lights and dipped
headlamps remain on for the duration
selected after the ignition is switched
off.
Disarming
When the function is disarmed,
the indicator light comes on on the
5-dial instrument panel display.
Do not cover the sunshine/
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
conditioning and for the automatic
switching on of the lights.

If the sunshine/brightness sensor
does not function correctly, the side
lights and dipped headlamps come on.
Consult a PEUGEOT dealer. Activation:

 switch off the engine,

 "fl ash" the headlamps,

 get out of the vehicle and lock it.

Page 84 of 250

5
74
Automatic switching on of the lights
The dipped beam headlamps switch
on automatically if the light is poor and
when the windscreen wipers operate
continuously. They switch off when
the light is bright enough or the wind-
screen wipers stop.
Warning: in foggy weather or in snow,
the brightness sensor can detect suf-
fi cient light. The lights will not come on
automatically.
If necessary, you must switch the
dipped headlamps on manually. Activation Manual "Follow-me-home"
lighting
When you leave your vehicle, the side
lights and dipped headlamps can be
left on for a few seconds.
When the function is activated,
the indicator light comes on on the
5-dial instrument panel display.
To disarm or activate the
function, pass via the
" P e r s o n a l i s a t i o n - c o n -
fi guration" menu on your
multifunction display.
For safety reasons, activation/
deactivation of the "Automatic
switching on of the lights"
function via the menu must be
carried out when stationary. To deactivate or activate the
"Automatic follow-me-home
lighting" function, pass via the

"Personalisation-confi gu-
ration" menu on your multi-
function screen.
The duration of timing can be
set via the "Personalisation-
confi guration" menu of your
multifunction display.
Automatic "Follow-me-home"
lighting
When you leave your vehicle
with the
automatic switching on of the lights
activated, the side lights and dipped
headlamps remain on for the duration
selected after the ignition is switched
off.
Disarming
When the function is disarmed,
the indicator light comes on on the
5-dial instrument panel display.
Do not cover the sunshine/
brightness sensor, located in
the centre of the windscreen.
It is used to regulate the air
conditioning and for the automatic
switching on of the lights.

If the sunshine/brightness sensor
does not function correctly, the side
lights and dipped headlamps come on.
Consult a PEUGEOT dealer. Activation:

 switch off the engine,

 "fl ash" the headlamps,

 get out of the vehicle and lock it.

Page 133 of 250

1010PRACTICAL INFORMATION
115
CHANGING A FRONT BULB
Handle the bulbs with a dry cloth.
2 - Main beam headlamps: H7-55 W.

 Remove the protective cover cor-
responding to the faulty bulb.

 Disconnect the connector.

 Press the end of the securing clips
to free the bulb. Change the bulb.

 When fi tting the new bulb, ensure that
the direction notches are positioned
correctly and the securing clips are
fi xed properly.

 Reconnect the connector.

 Refi t the protective cover.

4 -
Direction indicators:
PY 21 W (amber).

 Turn the bulb holder a quarter turn
and remove it.

 Change the bulb.

WARNING: RISK OF
ELECTROCUTION
Front lights
In the engine compartment, remove
the cover secured by one or two but-
terfl y screws, a plastic retainer clip and
two quarter turn screws.

1 - Dipped beam headlamps:
H1-55 W or D2S-35 W xenon bulb.
Xenon bulbs must be replaced by a
PEUGEOT dealer. Amber coloured bulbs (direction
indicators and side repeaters)
must be replaced with bulbs
of identical specifi cation and
colour.
5 - Front fog lamps: H11 - 55 W.
Turn the wheels to full lock.
Access to the bulb is via the fl ap in the
front mud fl ap.
Consult a PEUGEOT dealer.
The headlamps are fi tted with polycar-
bonate glass with a protective coating.
Do not clean them with a dry or abra-
sive cloth, nor with a detergent or sol-
vent product.
Ensure that the liquid used to fi ll the
wash-wipe and headlamp wash reser-
voir is of good quality.

High pressure washing :
when using a high pressure
washer on stubborn dirt, do
not persist on the headlamps,
the lights and their periphery to avoid
damaging their coating and their seal.
In certain climatic conditions (low tem-
perature, humidity), condensation on
the inside surface of the headlamp
glass and rear lights glass is normal;
it disappears a few minutes after the
lights are switched on.

3 - Side lights: W 5 W.

 Remove the protective cover, dis-
connect the connector and then
remove the bulb and change it.

 Put the connector back in place.

 Reconnect the connector.

 Refi t the protective cover.

Page 134 of 250

1010PRACTICAL INFORMATION
116
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.

 Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.

 Press on the two tabs located at
the rear, near the rear screen.

 Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.

 Change the faulty bulb.

 When refi tting, ensure that the
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.

 Screw on the light fi xing nuts in-
side the boot using the towing eye,
if necessary. When refi tting, en-
sure that the light is positioned and
fi xed correctly.

 Reconnect the connector.

Number plate lights:
W 5 W.

 Remove the transparent cover using
a screwdriver blade.

 Change the faulty bulb.

 Push the repeater forwards or
backwards and release it.

 Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi cation and colour.
1. Direction indicators:
PY 21 W (amber).

2. Reversing lights: P21 W.

3. Fog lamps/side lights:
P21/4 W.

4. Side lights: P21/4 W.

5. Brake lights/side lights: P21/4 W.

 Disconnect the connector.

 Unscrew the light fi xing nuts in-
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.

 Remove the seal.

 Unclip the bulb holder moving
aside the 5 tabs.

 Unscrew the bulb and change it.

 Lock the bulb holder in place.

 Reposition the seal.

Page 135 of 250

1010PRACTICAL INFORMATION
116
Integrated direction indicator side
repeaters CHANGING A REAR BULB (SALOON)
Third brake light:
Five W 5 W bulbs.

 Remove the plastic cover carefully
by unclipping it at the centre and
on either side, perpendicular to its
direction of engagement.

 Press on the two tabs located at
the rear, near the rear screen.

 Pull the red transparent cover out-
wards while maintaining the pressure
on the tabs.

 Change the faulty bulb.

 When refi tting, ensure that the
tabs of the red transparent cover
are engaged correctly and that the
upper trim has been put back in
place correctly.

 Screw on the light fi xing nuts in-
side the boot using the towing eye,
if necessary. When refi tting, en-
sure that the light is positioned and
fi xed correctly.

 Reconnect the connector.

Number plate lights:
W 5 W.

 Remove the transparent cover using
a screwdriver blade.

 Change the faulty bulb.

 Push the repeater forwards or
backwards and release it.

 Unclip the repeater and change it.
Repeaters can be obtained from
PEUGEOT dealers.
Amber coloured bulbs (direction indi-
cators and side repeaters), must be
replaced with bulbs of identical speci-
fi cation and colour.
1. Direction indicators:
PY 21 W (amber).

2. Reversing lights: P21 W.

3. Fog lamps/side lights:
P21/4 W.

4. Side lights: P21/4 W.

5. Brake lights/side lights: P21/4 W.

 Disconnect the connector.

 Unscrew the light fi xing nuts in-
side the boot using the towing eye
(stored inside the spare wheel), if
necessary.

 Remove the seal.

 Unclip the bulb holder moving
aside the 5 tabs.

 Unscrew the bulb and change it.

 Lock the bulb holder in place.

 Reposition the seal.

Page 136 of 250

1010PRACTICAL INFORMATION
117
CHANGING A REAR BULB (407 SW)
Left and right fog lamps:
P21 W.

 Carefully unclip the tailgate interior
trim.

 Detach the sealing sheet located
behind the light concerned.

 Remove the bulb holder turning it a
quarter of a turn.

 Change the faulty bulb.
When refi tting, ensure that the bulb is
positioned correctly in the bulb holder.

 Unclip the light (2 clips).

 Disconnect the connector and re-
move the light.

 Unclip the bulb holder moving
aside the 4 tabs.

 Unscrew the bulb and change it.

 Reconnect the connector.

 Lock the bulb holder in place.
When refi tting it, ensure that the
lamp is correctly positioned and
secured, reclipping the rear part
then the front part.

Number plate lights:
W 5 W.

 Insert a thin screwdriver in one of
the exterior holes of the transpar-
ent cover.

 Push it towards the outside to un-
clip it.

 Remove the transparent cover.

 Change the faulty bulb. Third brake light (diodes)
All work on the diode lights must be
carried out by a PEUGEOT dealer.
Wing lights

1. Brake lights/side lights:
P21/5 W.

2. Reversing lights:
P21 W.

3. Direction indicators:
P21 W.
These three bulbs are changed by
removing the light.

 Remove the corresponding boot
side fl ap to gain access to the
light.

 Remove the light fi xing nut inside
the boot.

Note: if necessary, use the wheelbrace
to remove the nuts. In some climatic conditions
(e.g. low temperature or hu-
midity), the presence of misting
on the internal surface of the
glass of the headlamps and rear lamps
is normal; it disappears after the lamps
have been on for a few minutes.