Peugeot 407 C 2010.5 Owner's Guide

1
24
Under-infl ation tyre
warning lamp
This indicates that the tyre
pressure is too low.
A message in the multifunction screen
indicates the wheel(s) concerned.
Refer to the information label affi xed
to the central pillar of the driver's door.
For your safety, check the tyre pres-
sures as soon as possible.
Electronic stability control system
(ESP) warning lamps
Activation warning lamp
Operation warning lamp
Deactivation warning lamp
Fault warning lamp
Parking brake warning
lamp
This indicates that the parking
brake is still applied or has not
been released correctly.
It is linked with the braking system
warning lamp.
Low screenwash and
headlamp wash fl uid level
warning lamp
When the wipers are switched
on, this indicates that the fl uid
level is too low.
Fill the screenwash and headlamp
wash fl uid reservoir. Battery charge warning
lamp
When the engine is running,
this indicates a charging cir-
cuit fault (battery terminals,
alternator belt).
Consult a PEUGEOT dealer. Engine oil level warning
lamp
This indicates a low engine
oil level.

Stop as soon as it is safe to do so.
Consult a PEUGEOT dealer.
INSTRUMENT PANEL SCREEN WARNING LAMPS
STOP warning lamp
It comes on linked with the
warning lamps for engine
oil pressure, coolant tem-
perature, power steering,
braking system or punctured tyre.

Stop as soon as it is safe to do so.
Consult a PEUGEOT dealer.
Low coolant level warning
lamp (according to
version)
This warning lamp indicates
that cooling system level is
too low.

Stop as soon as it is safe to do so.
Consult a PEUGEOT dealer.
Warning: the cooling system is pres-
surised, wait for the engine to cool
down before topping up the level.
When topping up, and in order
to prevent any risk of scalding,
unscrew the cap by two turns
to allow the pressure to drop.
When the pressure has
dropped, remove the cap and top up
the level with coolant. Power steering warning
lamp
This indicates a power stee-
ring fault.
It is linked with the STOP warning lamp.
Consult a PEUGEOT dealer.

1
25
Tyre under-infl ation
detection system warning
lamp
This indicates the absence
or fault with one or more tyre
pressure sensors or a sys-
tem fault.
Consult a PEUGEOT dealer.
Electronic engine
immobiliser warning lamp
This indicates an electronic
engine immobiliser system
fault.
Consult a PEUGEOT dealer. Front brake pad wear
warning lamp
This indicates that the brake
pads are worn.
For your safety, have them replaced
by a PEUGEOT dealer.
Fuel fi ller cap warning
lamp (according to
version)
With the engine running, this
indicates that the fuel fi ller
cap is incorrectly fi tted or missing.
It comes on in orange if the vehicle
speed is below 6 mph (10 km/h) and
in red if the vehicle speed is above
6 mph (10 km/h).
Door/boot open warning
lamp
With the engine running, this
indicates that an opening has
not been closed correctly.
An image in the multifunction screen
identifi es the opening concerned.
It comes on in orange if the vehicle
speed is below 6 mph (10 km/h) and
in red if the vehicle speed is above
6 mph (10 km/h). Airbag warning lamp
This indicates an airbag
fault.
Consult a PEUGEOT dealer.
Automatic headlamp
beam adjustment system
warning lamp
This indicates that the auto-
matic headlamp height adjust-
ment system is faulty.
Consult a PEUGEOT dealer.
Punctured tyre warning
lamp
This indicates that one or
more punctured tyres have
been detected.
A message in the multifunction screen
identifi es the wheel(s) concerned.
It is linked with the STOP warning
lamp.

Stop as soon as it is safe to do so.
Change the damaged wheel and have
it repaired by a PEUGEOT dealer.
Engine oil pressure
warning lamp
This indicates that the engine
oil pressure is too low.
It is linked with the STOP warning
lamp.

Stop immediately if it comes on while
the engine is running.
If there is a lack of oil in the lubrication
system, top up the level and contact a
PEUGEOT dealer as soon as possible.

1
26
Electronically controlled
suspension indicator lamps
This comes on when the
SPORT function is activated.
Automatic illumination of
headlamps on indicator
This comes on when the
AUTO function is activated.
Automatic illumination of
headlamps off indicator
This comes on when the AUTO
function is deactivated.
Automatic rain sensitive
wipers on indicator
This comes on when the
AUTO function is activated.
Automatic rain sensitive
wipers off indicator
This comes on when the
AUTO function is deactivated.
Service warning lamp
This is displayed to indicate
an engine management sys-
tem fault.
Contact a PEUGEOT dealer as soon
as possible.
Electronically controlled
suspension fault warning
lamp
This indicates an electroni-
cally controlled suspension
malfunction.
Select automatic operation and con-
tact a PEUGEOT dealer as soon as
possible.
Parking sensor system
warning lamp
In forward and/or reverse
gear, this indicates a parking
sensor system fault.
Consult a PEUGEOT dealer. This comes on when the
SPORT function is deacti-
vated.
Particle emission fi lter
saturation warning lamp
(Diesel engine)
With the engine running, this
indicates that the particle
emission fi lter is starting to become
saturated (exceptionally prolonged ur-
ban driving type conditions: low speed,
long traffi c jams...) or a low Diesel ad-
ditive reservoir level.
In order to regenerate the fi lter, you are
advised to drive, as soon as possible
when the traffi c conditions permit, at a
speed of 40 mph (60 km/h) or above
for at least fi ve minutes (until the warn-
ing lamp goes off).
If the warning lamp remains on, con-
tact a PEUGEOT dealer.
Following prolonged use of the vehi-
cle at very low speeds or at idle, you
may, exceptionally, notice an emission
of water vapour at the exhaust dur-
ing acceleration. This does not affect
the performance of the vehicle or the
environment. Water in Diesel fi lter
warning lamp
This indicates the presence
of water in the Diesel fi lter.
There is a risk of damage to
the injection system.
Contact a PEUGEOT dealer as soon
as possible.

1
27
Coolant temperature indicator
When the needle is in zone A , the
temperature is correct.
When the needle is in zone B , the
temperature is too high.
If the coolant temperature
warning lamp comes on
(linked with the STOP warn-
ing lamp), stop as soon as it
safe to do so.
Wait for the engine to cool down be-
fore topping up the level, if necessary.
As the cooling circuit is pres-
surised, in order to prevent
any risk of scalding, unscrew
the cap by two turns to allow
the pressure to drop.
When the pressure has dropped, re-
move the cap and top up the level with
coolant, if necessary.
Consult a PEUGEOT dealer.
This indicates an automatic
gearbox programme fault.
Automatic gearbox lever position indicators
Automatic gearbox fault
warning lamp
This indicates an automatic
gearbox fault.
The gearbox will operate in
down-grade mode, locked in
3rd gear.
Never force the gear lever.
Consult a PEUGEOT dealer.
6 speed automatic gearbox
"Park" indicator
"Reverse" indicator
"Neutral" indicator
"Drive" indicator
The letter S or the symbol , associ-
ated with the gear lever position indica-
tors, corresponds to the Sport or Snow
programme selected intentionally.
"Manual" indicators
These correspond to the manual con-
trol of the gearbox.
When the engine speed is too low or too
high in relation to the gear engaged, the
gear selected fl ashes for a few seconds,
then the actual gear is displayed, the
auto-adaptive programme having taken
control temporarily.

1
28
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer's servicing schedule.
Once an engine oil level indication has been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
ner fl ash.

Example : when the ignition is switched on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains on.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last
service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user's driving conditions.
Engine oil temperature indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is on.
The trip recorder display shows the
distance remaining (in round fi gures)
before the next service.

Example : when switching on the ig-
nition and for 5 seconds, the display
shows that 400 miles/900 km remain
before the next service is due.

1
28
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer's servicing schedule.
Once an engine oil level indication has been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
ner fl ash.

Example : when the ignition is switched on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains on.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last
service.
The distance remaining may be
weighted by the time factor, depend-
ing on the user's driving conditions.
Engine oil temperature indicator
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is on.
The trip recorder display shows the
distance remaining (in round fi gures)
before the next service.

Example : when switching on the ig-
nition and for 5 seconds, the display
shows that 400 miles/900 km remain
before the next service is due.

1
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder re-
set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information.
Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil fi ller cap,
using the type of oil suited
to your engine.

A = max.

B = min.
Oil level correct
Oil level too low
Flashing indicates that the oil level is
too low, which may damage the en-
gine.
If the low oil level is confi rmed by
checking with the dipstick, the level
must be topped up. Oil level indicator fault
(fl ashing segments)
Check the oil level using the dipstick.
If the level is correct, the fl ashing indi-
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes.
After this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
fi ve minutes, otherwise the zero
re-set will not be registered.

1
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:

 Switch off the ignition,

 Press and hold the trip recorder re-
set button,

 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information.
Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
level via the oil fi ller cap,
using the type of oil suited
to your engine.

A = max.

B = min.
Oil level correct
Oil level too low
Flashing indicates that the oil level is
too low, which may damage the en-
gine.
If the low oil level is confi rmed by
checking with the dipstick, the level
must be topped up. Oil level indicator fault
(fl ashing segments)
Check the oil level using the dipstick.
If the level is correct, the fl ashing indi-
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes.
After this operation, if you wish
to disconnect the battery, lock
the vehicle and wait for at least
fi ve minutes, otherwise the zero
re-set will not be registered.

1
30
Trip recorder zero reset
With the trip mileage displayed, press
the button for a few seconds.
Mileage recorder
The total mileage is displayed in
zone A of the screen and the trip mile-
age in zone B .
LIGHTING DIMMER
With the exterior lighting on, press the
button to vary the intensity of the light-
ing of the instruments and controls.
When the lighting reaches the mini-
mum (or maximum) setting, release
the button then press it again to in-
crease (or reduce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.

1
31
TRIP COMPUTER

or
TRIP: access to the trip
computer information.
Zero reset
When the required trip is displayed,
press the control for more than
two seconds. - trip
"1" tab with: