display Peugeot 407 C 2010.5 Owner's Manual

Page 16 of 243

Cruise control
This prevents the vehicle from exceed-
ing the speed programmed by the driver
(minimum speed 20 mph (30 km/h)).

1. Selection/Switching off speed limiter
mode.

2. Decrease the programmed value.

3. Increase the programmed value.

4. Speed limiter on/off.
The values must be set with the engine
running.

 97
Speed limiter

 99
This enables the vehicle to maintain
a constant speed programmed by the
driver.

1.
Selection/Switching off cruise control
mode.

2. Decrease the programmed value
and storing a speed.

3. Increase the programmed value and
storing a speed.

4. Cruise control on/off.
In order to be programmed or activated,
the vehicle speed must be higher than
25 mph (40 km/h), with at least fourth
gear engaged on the manual gearbox. The cruise control or speed limiter mode
appears in the instrument panel when it
is selected.

Cruise control

Speed limiter
Display in the instrument panel

Page 19 of 243

1
22
CHECK (vehicle self-test)
In the presence of a fault
A "minor" fault has been detected:
when the CHECK OK indicator lamp
has been displayed, the warning
lamp(s) is(are) displayed.
You can start your vehicle; however,
contact a PEUGEOT dealer as soon
as possible.
A "major" fault has been detected:
the CHECK OK indicator lamp does
not appear and the warning lamp(s)
is(are) displayed.
Do not start your vehicle.
Call a PEUGEOT dealer without delay. * According to country.
Automatic CHECK
With the key in the running (ignition
on) position, all of the warning lamps
of the functions tested are displayed.
They are switched off after a few sec-
onds.
At the same time, an automatic CHECK
(vehicle self-test) is carried out.
No "major" fault has been de-
tected: the CHECK OK indi-
cator lamp is displayed after
a few seconds.
You can start your vehicle. Manual CHECK
Pressing the
"CHECK/000" button on
the instrument panel starts the manual CHECK (vehicle self-test).
This function enables you to fi nd out, at
any time (with the key in the ignition on
position or with the engine running):
- the alerts present,
- the status of the functions activat-
ed or deactivated (automatic rain
sensitive wipers, automatic illumi-
nation of headlamps). The passenger's airbag deacti-
vated warning lamp * remains on
while the airbag is deactivated.

With the engine running and the ve-
hicle moving, the instrument panel
screen displays the warning lamps
(in the event of a fault).

Page 31 of 243

1
32
Press the "MENU" button to open the
main menu.
Select the "Trip computer" or

"Vehicle diagnostics" application
using the navigator, then confi rm or
press the "MODE" button until you
reach the trip computer screen, then
confi rm using "OK" .
The "Trip computer" or "Vehicle diag-
nostics" menu offers various options:
- Warnings log,
- Status of the functions,
- Input of the distance to be travelled.
Alert log
This summarises the active warning
messages, displaying them in the mul-
tifunction screen in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Distance remaining
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled value.
Display in the instrument panel screen
All of the various items of trip computer
information also appear on the instru-
ment panel screen at the same time.
Distance remaining to be travelled (miles or km)
Average speed (mph or km/h)
Average fuel consumption (mpg or l/100 or km/l)
Distance travelled (miles or km)
This is the average speed calculated
since the computer was last reset to
zero (with the ignition on).
This is the distance remaining to the
destination, either calculated at any
time by the navigation if guidance is
activated, or entered by the user, mi-
nus the distance covered since the
distance was entered.
If digits are missing, dashes are dis-
played in their place.
This is the average fuel consumption
since the computer was last reset to
zero.
This indicates the distance travelled
since the computer was last reset to
zero.
"TRIP" menu

Page 32 of 243

2
33
COLOUR SCREEN C
This displays the following informa-
tion, via the Peugeot Connect Sound
control panel:
- time,
- date,
- ambient temperature (the value displayed fl ashes if there is a risk
of ice),
- openings check,
- warning messages,
- audio functions,
- trip computer information,
- personalisation and confi guration displays,
- air conditioning settings,
- front and rear parking sensors dis- play,
- hands-free kit information. Management of the displays
For example: "TRIP"
Main menu
Press the
"MENU" button to gain ac-
cess to the main menu and select
one of the following functions:
- "Audio functions",
- "Trip computer",
- "Personalisation-Confi guration",
- "Air conditioning",
- "Telephone". "Personalisation-Confi guration"
menu
This provides access to successive
confi rmation windows.
Defi ne the vehicle parameters
This enables you to activate or deac-
tivate certain driving and comfort sys-
tems:
- "Automatic lighting of headlamps",
- "Guide-me-home lighting" and
"Duration",
- "Remote control action",
- "Permanent locking of the boot",
- "Directional headlamps".
The
"AUDIO" , "TRIP" , "CLIM" and

"TEL" buttons on the audio system
control panel allow display in the main
window.
For example: "Audio functions" For example: "Automatic lighting of
headlamps"

Page 33 of 243

2
34
Choice of language
German, Spanish, French, English,
Italian, Dutch, Turkish, Portuguese
and Brazilian Portuguese.
Display confi guration
- "Video brightness adjustment".
- "Date and time adjustment".
- "Choice of units".
- "Choice of colors". Setting the date and time
From the
main menu , select the

" P e r s o n a l i s a t i o n - C o n f i g u r a t i o n "
icon using the navigator, then confi rm.
From the list displayed, select "
Display
confi guration
" , then confi rm.
From the list displayed, select "
Date

and time
and adjustment
" , then con-
fi rm. Adjust the settings one by one:
- the zone selected is displayed on
the screen,
- use the navigator to move from one zone to another,
- your new settings are confi rmed one by one, by pressing the navi-
gator button,
- all of the changes are saved, if you click on "OK" on the screen, or
cancelled, if you press the "ESC"
button on the control panel.
For safety reasons, confi gu-
ration of the multifunction
screen by the driver must only
be done while stationary.

Page 34 of 243

2
35
Display
This menu allows you to set the bright-
ness of the screen, the screen colour
scheme and the colour of the map
(day/night and auto mode).
Vehicle
This menu permits the activation or
deactivation of certain driving and
comfort systems:
- air conditioning (A/C),
- vehicle information,
- access to the vehicle,
- driving assistance,
- lighting confi guration,
- comfort lighting.
Units
This menu permits selection of the units:
temperature (°C or °F) and fuel con-
sumption (km/l, l/100, miles and mpg).
System
This menu allows factory settings to be
restored, display of the software ver-
sion and activation of scrolling text. For safety reasons, confi gu-
ration of the multifunction
screen by the driver must only
be done when stationary. COLOUR SCREEN (WITH PEUGEOT CONNECT NAVIGATION) "SETUP" menu
Press the SETUP button to gain access
to the "SETUP" menu. This provides
access to the following functions:
- System language,
- Date & Time,
- Display,
- Vehicle,
- Units,
- System.
System language
This menu allows you to select the lan-guage used by the display: German,
English, Spanish, French, Italian,
Dutch, Polish, Portuguese.
Date & Time
This menu allows you to set the date
and time, the format of the date and
the format of the time (refer to the
"Audio and Telematics" section).
This displays the following information:
- time,
- date,
- ambient temperature (the value
displayed fl ashes if there is a risk
of ice),
- check of openings,
- vehicle function status messages, displayed temporarily,
- warning messages,
- audio functions,
- trip computer information,
- air conditioning settings,
- satellite navigation system infor- mation.

Page 36 of 243

2
37
Display confi guration
- "Choose colour",
- "Adjust brightness",
- "Adjust date and time",
- "Select units". "Video" menu
Defi ne the vehicle parameters
This enables you to activate or deacti-
vate certain driving and comfort func-
tions:
- "Automatic lighting of headlamps",
- "Guide-me-home lighting" and
"Duration",
- "Remote control action",
- "Directional headlights",
- "Permanent locking of the boot".
For example: "Automatic lighting of
headlamps"
You can connect video equipment (cam-corder, digital camera, DVD player, ...)
to the three video sockets, located in the
glove box.

Videos can only be displayed when
stationary.
Select the "Video" menu from the

main menu :
- "Activate video mode" to activate/ deactivate the video,
- "Video parameters" to set the dis- play format, the brightness, the
contrast and the colours.
Pressing the "DARK" button discon-
nects the display from the video.
Successive presses on the "SOURCE"
button permit the selection of an audio
source other than that of the video.
For safety reasons, confi gu-
ration of the multifunction
screen by the driver must only
be done when stationary.

Page 37 of 243

2
37
Display confi guration
- "Choose colour",
- "Adjust brightness",
- "Adjust date and time",
- "Select units". "Video" menu
Defi ne the vehicle parameters
This enables you to activate or deacti-
vate certain driving and comfort func-
tions:
- "Automatic lighting of headlamps",
- "Guide-me-home lighting" and
"Duration",
- "Remote control action",
- "Directional headlights",
- "Permanent locking of the boot".
For example: "Automatic lighting of
headlamps"
You can connect video equipment (cam-corder, digital camera, DVD player, ...)
to the three video sockets, located in the
glove box.

Videos can only be displayed when
stationary.
Select the "Video" menu from the

main menu :
- "Activate video mode" to activate/ deactivate the video,
- "Video parameters" to set the dis- play format, the brightness, the
contrast and the colours.
Pressing the "DARK" button discon-
nects the display from the video.
Successive presses on the "SOURCE"
button permit the selection of an audio
source other than that of the video.
For safety reasons, confi gu-
ration of the multifunction
screen by the driver must only
be done when stationary.

Page 44 of 243

3
44
PROGRAMMABLE HEATING Programming remote control
The heating system programming re-
mote control comprises the following
buttons and displays:

1. Scrolling functions menu buttons.

2. Function indicator lamps: clock,
temperature, operating time, pro-
grammed time, heater operation,
heating management symbols.

3. Digital displays: time, temperature,
duration of operation, programmed
time or level of heating.

4. Off button.

5. On button.
Displaying the functions

If a malfunction of the programmable
heating system occurs, contact a
PEUGEOT dealer.
The programmable heating operates
independently of the engine.
When the engine is off, it pre-heats
the coolant circuit in order to benefi t
from an optimum engine operating
temperature from the time the engine
is switched on.
The programmable heating system
is switched on using the long range
remote control. Activation can be im-
mediate or deferred by means of a
programming function.
screen
Press the buttons 1 in succession to
display the functions.
The fi rst press of the left-hand or right-
hand button displays the time.
Next, the left-hand button gives ac-
cess to the programming time then to
the level of heating (C1 to C5).
The right-hand button permits access
to the passenger compartment temper-
ature then to the duration of operation
of the heater if it is to be switched on
immediately.
The passenger compartment
temperature information is
only available when the en-
gine is off.

Page 149 of 243

134
02
1
2
VOICE COMMANDS
VOICE COMMANDS AND STEERING MOUNTED CONTROLS
DISPLAYING THE LIST AND USING THEM
To display the list of available voice commands, press the end of the lighting stalk to start voice recognition, then say HELP or WHAT CAN I SAY.
For the same operation, press and hold the MENU button and select the function VOICE COMMANDS LIST.
Press the end of the lighting stalk to start voice recognition.
Say the words one by one and wait for the audible confi rmation signal between each word.
The list which follows is exhaustive.
LEVEL 1 LEVEL 2 LEVEL 3
radio memory autostore previous/next list
1 to 6/*
cd player Jukebox (if activated) USB
previous/next track track number/track scan random play
directory (CD-MP3 inserted) list
1 to 250/* previous/next repeat help/what can I say/cancel
call/guide to "Pre-recorded description"
telephone last number voice box voice mail directory
"Pre-recorded description"
message display read directory
"Pre-recorded description"
navigation stop/resume zoom in/out view
* destination vehicle
traffi c info display read
display audio telephone trip computer Navigation air conditioning
previous/next stop delete yes/no
for all level 1 and 2
* help/what can I say/cancel for all level 1, 2 or *
Voice commands list

Page:   1-10 11-20 21-30 next >