Peugeot 407 Dag 2004.5 Workshop Manual

46 -
11-10-2004
47
-
11-10-2004
407 saloon and 407 SW comfort
(*) The rules for transporting children in the front passenger se
at are specific to each country. Consult the current legislation
in your country.
INSTALLATION OF CHILD SEATS
In accordance with the European regulation (Directive 2000/3), this table indicates the options for the installation of child
seats secured using the seat belt and universally approved in relation to weight of the child and the seat in the vehicle.
Group 0+ Group 1 Group 2 Group 3
from birth to 1 year or weighing up to 13 kg from 1 to 3 years
or weighing 9 to 18 kg from 3 to 6 years
or weighing 15 to 25 kg from 6 to 10 years
or weighing 22 to 36 kg
U: seats suited to the installation of a child seat secured usi ng the seat belt and universally approved. "Rear facing" child
seats and "forward facing" child seats.
Front passenger seat (*)
with fixed seat U U U U
Rear side seats
U (R): seats suited to the installation of a child seat secured usi ng the seat belt and universally approved.
"Rear facing" child seats and "forward facing" child seats. The pa ssenger seat must be adjusted to the highest position.
Front passenger seat (*)
with height
adjustable seat U (R) U (R) U (R) U (R)
X: seat not suited to the installation of a child seat.
Rear centre seat X X X X

48 -
11-10-2004
49
-
11-10-2004
SEAT BELTS
Front seat belt height adjustment:
F
To lower the attachment point,
squeeze control 1 and slide it
downwards.
F To raise the attachment point,
squeeze control 1 and slide it up-
wards.
To fasten the seat belts
F Pull the strap, then insert the end
into the clasp.
To unfasten the seat belts
F Press the button on the clasp. With the engine running
and when
all of the doors are closed, you are
warned for 30 seconds by lighting of
the seat belt warning light and by a
message on the multifunction display
which indicates which rear seat belts
are fastened.
407 saloon and 407 SW comfort
Front seat belts with pre-
tensioner and force limiter
In the event of a serious impact, the
pre-tensioning system instantly tight-
ens the seat belts irmly against the
bodies of the occupants.
The pre-tensioning seat belts are
armed when the ignition is on.
The force limiter reduces the pres-
sure of the seat belt on the body of
the occupant in the event of an ac-
cident.
* During the year.
Rear seat belts
The rear seats are all itted with a
three-point inertia reel seat belt.
The rear side seat belts have a force
limiter and may be itted with a pre-
tensioning inertia reel.
Before folding the seat back, pull the
strap and insert the seat belt buckle
into the clasp. This precaution will
ensure that each seat belt is in place
when the rear seats are lifted again.
Detection of fastening of the rear
seat belts*
When the ignition is switched on
,
if a rear passenger has not fastened
his seat belt, you are warned by light-
ing of the seat belt warning light . Warnings when a front or rear
seat belt is unfastened
- If the vehicle speed is
below 13 mph
(20 km/h) , you are warned by light-
ing of the seat belt warning light .
The warning light switches off when
the seat belt(s) concerned is(are)
fastened.
- If the vehicle speed is above 13 mph
(20 km/h) , you are warned by lash-
ing of the seat belt warning light ,
an audible signal and a message on
the multifunction screen locating the
unfastened seat belt(s).
Note: a bag or an animal placed on
a seat may trigger the lighting of the
warning light.
The audible signal ceases and the
warning light switches off when the
seat belt(s) concerned is(are) fas-
tened.
After two minutes without any action
on the seat belts, the lashing warn-
ing light remains on permanently and
the audible signal ceases.
All of the warnings cease when a
door is opened or when the engine is
switched off.

50 -
11-10-2004
51
-
11-10-2004
Wherever you are seated in
the vehicle, always fasten
your seat belt, even for short
journeys.
Do not invert the seat belt buckles as
they will not fulil their role fully.
If the seats have armrests*, the lap
part of the seat belt must always
pass under the armrest.
Before and after use, ensure that the
seat belt is rolled up correctly.
In order to be effective, a seat belt:
- must be tightened as close to the body as possible,
- must restrain one adult only,
- must not bear any trace of cuts or fraying,
- must not be twisted,
- must not be transformed or modiied. Clean the seat belt straps with soapy
water or a textile cleaning product,
sold by PEUGEOT dealers.
After folding or moving a seat or rear
bench seat, ensure that the seat belt
is positioned and rolled up correctly.
Recommendations for child seats:
- use a suitable child seat if the pas-
senger is less than 12 years old or
shorter than one metre ifty,
- do not use the strap-guide* when a child seat is installed.
Depending on the nature and se-
riousness of the impacts , the pre-
tensioning device may be triggered
before and independently of the air
bags.
In all cases, the air bag warning light
comes on.
Following an impact, have the seat
belts system checked, and if nec-
essary replaced, by a PEUGEOT
dealer.
* According to model.
407 saloon and 407 SW comfort

50 -
11-10-2004
51
-
11-10-2004
MANUAL STEERING WHEEL
HEIGHT AND DEPTH
ADJUSTMENT
When the vehicle is stationary, un-
lock the steering wheel by pushing
the control forwards.
Adjust the height and depth of the
steering wheel then lock by pulling
the control fully.
ELECTRIC ADJUSTMENT OF
THE HEIGHT AND DEPTH OF
THE STEERING WHEEL
When stationary, adjust the height or
depth of the steering wheel by mov-
ing the control:
F
forwards or backwards to adjust
the depth.
F up or down to adjust the height.
THE WELCOME FUNCTION
When the driver's door is opened, the
steering wheel rises to make access
to or exit from the vehicle easier.
You can activate or de-
activate this function via
the "personalisation-con-
figuration" menu on the
multifunction display.
HORN
Press one of the spokes or the centre
of the steering wheel.
407 saloon and 407 SW comfort

52 -
11-10-2004
53
-
11-10-2004
Memorising driving positions
The electrical adjustments of the
seat, exterior mirrors and steering
wheel are memorised.
Two driving positions can be memo-
rised using
buttons M/1 and M/2 . Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position of
the driver's seat, the exterior mirrors
and the electrical adjustment of the
steering wheel.
When unlocking the doors, the driv-
er's seat, the exterior mirrors and the
electrical adjustment of the steering
wheel resume the position memo-
rised by the remote control key, if the
settings have been changed in the
meantime.
Each remote control key can memo-
rise a speciic setting.
Recalling a memorised driving
position
Engine off
F
Briely press button 1 or 2 to recall
the corresponding memorised
position. The end of the setting is
indicated by a bleep.
After recalling a memorised position
a few times in succession, the func-
tion will be cancelled until the engine
is started.
Engine running
F Keep button 1 or 2 pressed down
until the bleep indicates that set-
ting of the corresponding memo-
rised position is complete.
Memorising using the controls on
the driver's door
To memorise:
F Place the key in the ignition on
position,
F Adjust your seat, mirrors and
steering wheel,
F Press button M, then button 1 "irst
driving position" or button 2 "sec-
ond driving position" within four
seconds.
An audible signal conirms that a po-
sition has been memorised.
Memorising a new position cancels
the previous one.
407 saloon and 407 SW comfort

52 -
11-10-2004
53
-
11-10-2004
EXTERIOR MIRRORS
Adjustment
F
Move control A to the right or to
the left to select the correspond-
ing mirror.
F Direct control B in all four direc-
tions to adjust.
Folding back the mirrors
electrically
- from inside: F With the ignition on, move the
control A to the central position
then pull it rearwards.
- from outside:
F Lock the vehicle using the remote
control* or the key.
This function can be deactivated.
Contact your PEUGEOT dealer.
When the vehicle is parked, the exterior
mirrors can be folded back manually.
* According to version. Automatic tilting of the mirrors in
reverse gear
This function allows you to see the
ground (kerb, wall...) when carrying
out parking manoeuvres in reverse
gear.
Initial setting of the function
Engage reverse gear then select and
adjust the left mirror then the right
mirror.
These settings will be stored when
the vehicle is locked.
Each remote control stores a speciic
setting.
Tilting the mirror to the parking
position
F
engage reverse gear,
F move control A to the right or the
left to select the corresponding
mirror.
The exterior mirror corresponding to
the side on which you are parking
tilts downwards.
Intentional returning of the mirror to
the driving position:
F change out of reverse gear or
deselect the mirror.
The mirror returns to the driving
position automatically if the vehicle
speed exceeds 10 mph (15 km/h),
if the engine is switched off or if re-
verse gear is engaged for more than
20 seconds. Objects observed in the
driver and passenger mirrors
are, in reality, closer than
they appear.
This must be taken into account in or-
der to judge the distance of vehicles
approaching from behind correctly.
407 saloon and 407 SW comfort

54 -
11-10-2004
55
-
11-10-2004
INTERIOR MIRROR
Automatic day/night interior
mirror
This automatically and gradually
changes between the day and night
positions. To prevent dazzling, the
glass of the mirror darkens auto-
matically depending on the intensity
of the light from behind. It clears as
the light (headlamps of following ve-
hicles, sunlight) decreases, ensuring
maximum visibility. Operation
Switch on the ignition and press
switch
1:
- Indicator light 2 lit (switch pressed):
automatic operation.
- Indicator light 2 off: automatic sys-
tem off. The mirror remains at its
most clear.
Special feature
To ensure maximum visibility dur-
ing manoeuvres, the mirror clears
automatically when reverse gear is
engaged.
Manual interior mirror
The interior mirror has two positions:
- day (normal),
- night (anti-dazzle).
To change from one to the other,
push or pull the lever on the lower
edge of the mirror.
407 saloon and 407 SW comfort

54 -
11-10-2004
55
-
11-10-2004
WINDSCREEN WIPER STALK
Front windscreen wiper with
intermittent wipe
2
Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
l Intermittent wipe.
0 Off.
â Single wipe (press
downwards).
In the Intermittent position, the wi-
ping speed is in proportion to the
vehicle speed. Front windscreen wiper with
automatic wipe
2
Fast wipe (heavy rain).
1 Normal wipe (moderate rain).
AUTO Automatic wipe.
0 Off.
â Single wipe (press
downwards).
In the AUTO position, no action on
your part is necessary. Automatic windscreen wipers

An indicator light comes
on on the instrument
panel display. It is accompanied by a
message on the multi-
function display.
Move the control to position
0 then
return it to the AUTO position.
Activation
In the
AUTO position, the wind-
screen wipers operate automatically
and adapt their speed to the intensity
of the rainfall.
If the ignition was switched off
more than one minute ago with the
control in the AUTO position, this
function must be re-activated.
407 saloon and 407 SW comfort

56 -
11-10-2004
57
-
11-10-2004
Windscreen and headlamp wash
Pull the windscreen wiper stalk to-
wards you. The windscreen wash
then the windscreen wipers operate
for a ixed period.
The headlamp wash operates at the
same time for two seconds,
only if
the headlamps are on.
Disarming
Manual operation of the wiper stalk
interrupts the
AUTO position, the de-
activation indicator light comes on on
the 5-dial instrument panel display,
accompanied by a message on the
multifunction display.
In the event of malfunction , the
windscreen wipers will operate in
intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
CHANGING A WINDSCREEN
WIPER BLADE
Placing the wiper blades in the
maintenance position
F Less than one minute after switch-
ing off the ignition, press the wind-
screen wiper stalk down once to
position the blades in the centre
of the windscreen (maintenance
position).
Replacing a blade
F Lift the arm, then unclip the blade
and remove it.
F Fit the new blade and fold down
the arm.
To park the blades, switch on the
ignition and operate the windscreen
wiper stalk.
Do not cover the rain sensor
located on the windscreen
behind the interior mirror.
When using an automatic car
wash to wash your vehicle, switch off
the ignition or check that the wiper
stalk is not in the automatic position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
407 saloon and 407 SW comfort

56 -
11-10-2004
57
-
11-10-2004
Windscreen and headlamp wash
Pull the windscreen wiper stalk to-
wards you. The windscreen wash
then the windscreen wipers operate
for a ixed period.
The headlamp wash operates at the
same time for two seconds,
only if
the headlamps are on.
Disarming
Manual operation of the wiper stalk
interrupts the
AUTO position, the de-
activation indicator light comes on on
the 5-dial instrument panel display,
accompanied by a message on the
multifunction display.
In the event of malfunction , the
windscreen wipers will operate in
intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.
CHANGING A WINDSCREEN
WIPER BLADE
Placing the wiper blades in the
maintenance position
F Less than one minute after switch-
ing off the ignition, press the wind-
screen wiper stalk down once to
position the blades in the centre
of the windscreen (maintenance
position).
Replacing a blade
F Lift the arm, then unclip the blade
and remove it.
F Fit the new blade and fold down
the arm.
To park the blades, switch on the
ignition and operate the windscreen
wiper stalk.
Do not cover the rain sensor
located on the windscreen
behind the interior mirror.
When using an automatic car
wash to wash your vehicle, switch off
the ignition or check that the wiper
stalk is not in the automatic position.
In winter, it is advisable to wait for the
windscreen to completely clear of ice
before operating the automatic wipe.
407 saloon and 407 SW comfort