Peugeot 407 Dag 2005 Owner's Manual

136 -
14-02-2005
137
-
14-02-2005
ANTI-LOCK BRAKING
SYSTEM (ABS)
The ABS increases the stability and
manoevrability of your vehicle on
braking, in particular on poor or slip-
pery road surfaces.
This system comes into operation
automatically when there is a risk of
wheel lock.
Normal operation of the ABS may
make itself felt by slight vibrations of
the brake pedal.
In emergency braking, press very
irmly without releasing the pres-
sure.
Note:
when changing wheels (tyres
and rims), make sure that these are
approved.
EMERGENCY BRAKING
ASSISTANCE SYSTEM
In an emergency, this system enables
the optimum braking pressure to be
reached more quickly, thus reducing
the stopping distance.
It is triggered by the speed at which
the brake pedal is activated. The
effect of this is a reduction in the re-
sistance of the pedal and an increase
in braking eficiency.
This indicates that the ABS
is faulty.
It comes on on the instru-
ment panel screen also.
If it comes on permanently above
6 mph (10 km/h), it indicates an ABS
malfunction.
However, the vehicle retains conven-
tional servo-assisted braking.
Contact a PEUGEOT dealer.
407 saloon and 407 SW comfort

127
-
14-02-2005
Warning:
the vehicle speed must
be above 25 mph (40 km/h) in or-
der to be able to activate the cruise
control.
On a vehicle itted with a manual
gearbox, it is also necessary to be in
at least fourth gear.
On a vehicle itted with an automatic
gearbox, it is necessary to be either
in position D, or in selective driving
mode in a gear higher than or equal
to position 2.First activation
F Place the dial 1 in the "On" posi-
tion to access the cruise control
function.
F Position the speedometer needle
at the speed required.
F Press button 2 "set-" or 3 "set+" to
activate the cruise control.
At this moment, the vehicle speed is
maintained without any intervention
on your part. It is stored as the cruis-
ing speed which is displayed:
CRUISE CONTROL
The cruise control function allows you
to choose and maintain a constant
vehicle speed, called the "cruising
speed", irrespective of the proile of
the road and without any action on
the part of the driver on the accelera-
tor pedal or the brake pedal.
The "cruising speed" is chosen by
the driver and must comply with the
highway regulations in use at local
and national level.
The cruise control function must not
be used on slippery roads or in heavy
trafic.
on the 5-dial instrument panel display
on the 4-dial instrument panel display
Adjust your selection
When the cruise control is activated,
pressing button
3 "set+" increases
the cruising speed displayed on the
instrument panel.
Pressing button 2 "set-" reduces the
cruising speed displayed on the in-
strument panel.
Short press: +/- 1 mph (1 km/h)
Long press: +/- 5 mph (5 km/h)
Maintained press: continuous in-
crease or decrease of the value in
steps of 5 mph (5 km/h).
The vehicle gradually reaches the
new cruising speed displayed on the
instrument panel.
You can drive faster than the cruising
speed at any time by pressing the
accelerator pedal. This does not de-
activate the cruise control. When you
release the accelerator pedal, the ve-
hicle returns to the cruising speed.
Pressing button 3 "set+" or 2 "set-"
while you are driving faster than the
cruising speed stores the current
speed as a new cruising speed.
407 saloon and 407 SW comfort

128 -
14-02-2005
129
-
14-02-2005
Deactivating the cruise
control
The cruise control is deactivated by
the following actions:
- pressing cruise control button
4
"Cancel",
- pressing the brake pedal,
- pressing the clutch pedal on a vehi- cle itted with a manual gearbox,
- selecting a gear which is not au- thorised on a vehicle itted with an
automatic gearbox.
The cruise control is also deactivated
in the following circumstances:
- when the vehicle speed falls below 22 mph (35 km/h),
- when the ESP is activated.
End of cruise control mode
F Place the dial in the "Off" posi-
tion.
Note: after placing the dial 1 in the
"Off" position or after switching off
the engine, it is necessary to repeat
the "First activation" stage in order to
activate the cruise control. When the cruise control is selected
and a fault is present, a warning
light comes on, an audible signal is
heard and a message appears on
the multifunction display. Contact a
PEUGEOT dealer to have the sys-
tem checked.
Reactivating the cruise control
If the conditions necessary for activa-
tion are met (see § First activation),
the cruise control can be reacti-
vated:
- by pressing button 4 "Cancel" to
regain the cruising speed stored,
- by pressing button 2 "set-" or 3
"set+" to store the current speed as
the new cruising speed.
Display on the instrument
panel
When the dial is in the "ON" position,
the cruise control symbol is displayed
on the instrument panel associated
with a description "OFF" indicating
that the speed reference value has
not yet been entered.
To the right of the symbol, dashes
indicate that a irst activation has not
yet taken place.
When the irst activation takes place,
the description "OFF" disappears
and the dashes are replaced by the
display of the cruising speed stored.
When the driver exceeds the cruising
speed, it lashes on the instrument
panel.
When the cruise control is deac-
tivated, the description "OFF" ap-
pears; the cruising speed stored is
still displayed.
When the cruise control is reacti-
vated, lashing of the cruising speed
for a few seconds indicates that the
activation conditions have not been
met.
407 saloon and 407 SW comfort

128 -
14-02-2005
129
-
14-02-2005
CRUISE CONTROL/SPEED
LIMITER
Cruise control function
This enables the vehicle to maintain
a steady speed programmed by the
driver, regardless of the road charac-
teristics and without the driver hav-
ing to touch the accelerator or brake
pedals.
In order for it to be memorised, the
vehicle speed must be greater than
25 mph (40 km/h) with at least fourth
gear engaged (second gear for the
automatic gearbox),
with the engine
running .
Selecting the function
F Place switch 1 in the CRUISE
position. The cruise control is
not yet active and no speed has
been memorised. The display in-
dicates:
Switching the function off
F Place switch 1 in position 0 or
LIMIT to switch the system off. Note:
It is possible to accelerate
and drive momentarily at a speed
greater than the memorised speed.
The value memorised lashes. When
the accelerator pedal is released, the
vehicle will return to the memorised
speed.
Cancelling the memorised speed
If you wish to cancel the memorised
speed:
F Press button 4 or the brake or
clutch pedal. The display indicates
(e.g. at 70 mph (110 km/h)):
Activation/memorising a speed
As soon as you reach the chosen
speed, press button 2 or 3. This
memorises the speed, which will
be maintained automatically. The
display indicates (e.g. at 70 mph
(110 km/h)):
407 saloon and 407 SW comfort

130 -
14-02-2005
131
-
14-02-2005
Note:
the speed memorised is can-
celled automatically if the vehicle
speed is less than 25 mph (40 km/h),
or if the manual gearbox is in a gear
lower than fourth (second gear for
the automatic gearbox) or if the ESP
is activated. Operating check
In the event of a cruise control mal-
function, the memorised speed is
erased, the dashes lash for a few
seconds:
A warning light comes on, an audible
signal is heard and a message ap-
pears on the multifunction display.
Contact a PEUGEOT dealer to have
the system checked.
Do not use the cruise control
on slippery roads or in heavy
trafic.
Changing a memorised speed
To memorise a speed higher than the
previous one, there are two options:
Without using the accelerator:
F
press button 3;
Using the accelerator:
F exceed the memorised speed un-
til the required speed is reached,
F press button 2 or 3.
To memorise a speed lower than the
previous one:
F press button 2;
Short press: +/- 1 mph (1 km/h)
Long press: +/- 5 mph (5 km/h)
Maintained press: continuous in-
crease or decrease of the value in
steps of 5 mph (5 km/h).
Recalling the memorised speed
After cancellation, press button
4.
Your vehicle will return to the last
memorised speed. The display indi-
cates (e.g. at 70 mph (110 km/h)):
Cancelling the memorised speed
F Place switch 1 in position 0 or
LIMIT or switch off the ignition.
407 saloon and 407 SW comfort

130 -
14-02-2005
131
-
14-02-2005
CRUISE CONTROL/SPEED
LIMITER
Limiter function
This prevents the vehicle speed
exceeding the speed programmed
by the driver (minimum speed of
18 mph (30 km/h)).
The operations must be carried
out with the engine running. Selecting the function
F
Place switch 1 in the LIMIT posi-
tion. The limiter is not yet active.
By default the display indicates:
Switching the function off
F Place switch 1 in position 0 or
CRUISE or switch off the ignition
to switch the system off. The last
speed programmed remains in
the memory. Memorising a speed
A speed can be memorised without
activation of the limiter.
Pressing buttons
2 and 3 decreases
or increases the speed.
Short press: +/- 1 mph (1 km/h)
Long press: +/- 5 mph (5 km/h)
Maintained press: continuous in-
crease or decrease of the value in
steps of 5 mph (5 km/h).
Activation/deactivation of the
limiter
Pressing button 4 activates the lim-
iter, pressing this button again deac-
tivates it.
When the limiter is active, the display
indicates (e.g. at 70 mph (110 km/h)):
407 saloon and 407 SW comfort

132 -
14-02-2005
133
-
14-02-2005
Exceeding the programmed
speed
Additional pressing of the accelera-
tor to exceed the programmed speed
will have no effect unless the pedal is
pressed irmly (passing the
point of
resistance ).
The limiter is deactivated temporarily
and displays the programmed speed
(e.g. at 70 mph (110 km/h)):
If a mat is used which is not
recommended by PEUGEOT,
there is a risk that it may slide
under the accelerator pedal
and prevent pressing of the pedal
past the point of resistance.
In this case, it will only be possible to
exit from the speed limiter function by
operating the steering wheel stalk.
Operating check
In the event of a limiter malfunction,
the memorised speed is erased, the
dashes lash for a few seconds:
Note: the speed also lashes when
the speed limiter cannot prevent
the vehicle from exceeding the pro-
grammed speed (on a steep descent
or in the event of sharp accelera-
tion).
To re-activate the limiter, release the
accelerator to slow down to a speed
below the programmed speed. A warning light comes on, an audible
signal is heard and a message ap-
pears on the multifunction display.
Contact a PEUGEOT dealer to have
the system checked.
407 saloon and 407 SW comfort

136 -
14-02-2005
137
-
14-02-2005
ELECTRONIC STABILITY
CONTROL (ESP)
This system is linked and comple-
mentary to the ABS system.
In the event of a signiicant variation
between the trajectory of the vehicle
and the path required by the driver,
the ESP monitors wheel by wheel
and acts automatically on the engine
and on the brake of one or more
wheels, to put the vehicle back on
course, within the limit of the laws of
physics.
ESP operation
The indicator light
lashes.
The indicator light
comes on. Disarming the ESP
In exceptional conditions (starting
the vehicle when it is stuck in the
mud, immobilised in snow, on unsta-
ble ground...), it may be advisable to
disarm the ESP.
F
Press the "ESP OFF" switch, lo-
cated on the centre console.
The switch lights up and the warning
light comes on: the ESP no longer
acts on the operation of the engine.
Instrument panel
indicator light.
Instrument panel
indicator light.
The system is triggered again:
F automatically if the ignition is
switched off,
F automatically above 30 mph
(50 km/h),
F manually by pressing the switch
again. Operating fault
When a malfunction of the system
occurs, the warning light comes on,
accompanied by an audible signal
and a message on the multifunction
display.
Contact a PEUGEOT dealer to have
the system checked.
Instrument panel
indicator light.
Instrument panel
indicator light.
The ESP offers exceptional
safety during normal driving,
but this should not encour-
age the driver to take extra
risks (late braking) or drive at high
speed.
Correct operation of the system de-
pends on compliance with the manu-
facturer's recommendations regarding
the wheels (tyres and rims), the brak-
ing components, the electronic com-
ponents and the PEUGEOT assembly
and operation procedures.
After an impact, have the system
checked by a PEUGEOT dealer.
407 saloon and 407 SW comfort

138 -
14-02-2005
139
-
14-02-2005
F
Press switch 1, the indi-
cator light comes on and
the SPORT warning light
comes on.
Manual selection of the SPORT
position
F Press switch 1 again. The
indicator light is switched
off and the AUTO indica-
tor light comes on.
To return to automatic operation
In this position, the suspension is
maintained in the
SPORT position. In the event of a fault
, it
comes on, accompanied by
an audible signal and a mes-
sage on the multifunction
display.
Select automatic operation and
contact a PEUGEOT dealer as soon
as possible.
Operating check
This is conirmed by the switch light
and the indicator lights.
ELECTRONICALLY
CONTROLLED SUSPENSION
The suspension adapts automatically
and instantly to different driving styles
and road characteristics, improving
the comfort of the occupants and
the vehicle's road holding capabili-
ties. The suspension favours smooth
shock absorption, ensuring a comfort-
able ride, but as soon as conditions
demand a change (sporty driving,
tight bends, avoidance action, etc.)
it automatically selects irmer shock
absorption, guaranteeing optimum
road holding.
407 saloon and 407 SW comfort

138 -
14-02-2005
139
-
14-02-2005
REAR PARKING ASSISTANCE
This system consists of four prox-
imity sensors, located in the rear
bumper.
This detects any obstacle (person,
cyclist, vehicle, tree, gate, etc.) be-
hind the vehicle. Nevertheless, it
cannot detect obstacles located just
below the bumper.
Warning:
an object, such as a stake,
a roadworks cone or any other simi-
lar object detected at the beginning
of the manoeuvre may no longer be
detected during the manoeuvre.
To make manoeuvres in reverse gear
easier, adjust your mirrors in accord-
ance with the "Automatic tilting of the
mirrors in reverse gear" function.
Maintenance: ensure that the sen-
sors are not covered with mud, frost
or snow.
Deactivation
If there is an operating fault,
on changing to reverse gear
a warning light on the instru-
ment panel, an audible signal
and a message on the multifunction
display indicate that there is a sys-
tem malfunction.
Contact a PEUGEOT dealer.
Your vehicle's rear speakers emit an
audible signal:
- on the right if an obstacle is
detected on the right,
- on the left if an obstacle is detected on the left,
- on the right and left if an obstacle is detected in the centre.
When the distance between the rear
of the vehicle and the obstacle is less
than approximately twenty-ive centi-
metres, the audible signal becomes
continuous.
Activation
The system is activated as soon as
reverse gear is engaged; an audible
bleep shows that it is active.
The proximity information is given by
an audible signal, which becomes
more rapid as the vehicle approach-
es the obstacle.Switching the system off
F Change to neutral, the system is
again inactive. F
Press the switch on the
centre console.
The indicator light on the switch
comes on and the system becomes
completely inactive.
407 saloon and 407 SW comfort