ignition Peugeot 407 Dag 2010 Owner's Manual
Page 5 of 249
FAMILIARISATION INSTRUMENTS AND CONTROLS
1. Steering wheel height and reach
adjustment.
2. Lighting/Direction indicator control
stalk.
3. Instrument panel.
4. W i p e r / W a s h - w i p e / T r i p c o m p u t e r
control stalk.
5. Air diffuser vent grille.
6. Speakers (tweeters).
7. P a s s e n g e r - o p e r a t e d e l e c t r i c
window control.
8. Cooled glove box.
9. Audio equipment steering mounted
controls.
10. Steering lock and ignition.
11. Cruise control/speed limiter
controls.
12. Storage compartment
(driver's side).
Fusebox.
13. Headlamp height adjustment.
14. Bonnet release.
Page 9 of 249
FAMILIARISATION
Front seat belt
1. Fastening.
2. Height adjustment.
1. Stop position.
2. Ignition position.
3. Starting position.
67
Electric window controls
1. Driver's electric window switch.
2. Passenger electric window switch.
3. Rear right electric window switch.
4. Rear left electric window switch.
Ignition switch
88
Also...
5. Deactivation of the electric
window switches located in
the rear (child safety).
A h e a v y o b j e c t ( k e y f o b . . . ) , a t -
tached to the key and weighing
down on its shaft in the ignition
switch, could cause a malfunction.
Page 12 of 249
FAMILIARISATION
Instrument panel
A. When the ignition is on, the fuel
gauge needle should rise.
B. W h e n t h e e n g i n e i s r u n n i n g , i t s a s -
sociated low level warning lamp
should switch off.
C. When the ignition is on, the oil level
indicator should display "OIL OK"
for a few seconds.
If the levels are not correct, top up the
level which is low.
Lighting of the indicator lamp indicates
the status of the corresponding function. When the ignition is on, the orange and
red warning lamps come on.
When the engine is running, these
warning lamps should switch off.
If any warning lamp remains on, refer to
the page concerned.
18
20
104
A. Audible front/rear parking
sensors off.
B. Central locking.
C. Alarm interior volumetric
protection off.
D. Hazard warning lamps.
E.
S e l e c t i o n o f t h e e l e c t r o n i -
cally controlled suspension.
F. E l e c t r o n i c s t a b i l i t y p r o -
gramme ESP off.
62
65
86
97
86
Warning lamps Switch panel
Page 13 of 249
FAMILIARISATION
1. Insertion the key.
2. Select the "OFF" position
3. Removal the key keeping the switch
in the new position. This prevents opening of the two rear
doors from the inside.
With the ignition on, press the button.
A m e s s a g e a p p e a r s o n t h e m u l t i f u n c -
tion screen.
You are advised to check that the child
lock is activated each time you switch
on the ignition.
When the
ignition is switched on , if
a front occupant has not fastened their
seat belt and if the vehicle speed is be-
low 12 mph (20 km/h) , you are warned
by the seat belt warning lamp which
comes on.
The warning lamp switches off when the
seat belt(s) concerned is(are) fastened.
If the vehicle speed is above 12 mph
(20 km/h) , you are warned by the seat
belt warning lamp w h i c h fl a s h e s , a n
audible signal and a message on the
multifunction screen identifying the seat
belt(s) left unfastened.
Detection of front seat belt
fastening
91
88
64
Front passenger's airbag
Electric child lock
Page 17 of 249
1
20
CHECK (VEHICLE AUTOTEST)
In the presence of a fault
A "minor" fault has been detected:
when the CHECK OK indicator lamp
has been displayed, the warning
lamp(s) is(are) displayed.
You can start your vehicle; however,
contact a PEUGEOT dealer as soon
as possible.
A "major" fault has been detected:
the CHECK OK indicator lamp does
not appear and the warning lamp(s)
is(are) displayed.
Do not start your vehicle.
Call a PEUGEOT dealer without delay.
Automatic CHECK
With the key in the ignition on position,
all of the warning lamps of the func-
tions tested are displayed. They are
switched off after a few seconds.
At the same time, an automatic CHECK
(vehicle autotest) is carried out.
No "major" fault has been de-
tected: the CHECK OK indi-
cator lamp is displayed after
two seconds.
You can start your vehicle.
Pressing the "CHECK/000" button on
the instrument panel starts the manual
CHECK (vehicle autotest).
T h i s f u n c t i o n e n a b l e s y o u t o fi n d o u t , a t
any time (with the key in the ignition on
position or with the engine running):
- the warnings present,
- the status of the functions activated or deactivated (wipers, automatic
illumination of headlamps).
Manual CHECK
The passenger airbag deactiva-
ted indicator lamp * remains on
while the airbag is deactivated.
With the engine running and the ve-
hicle moving, the instrument panel
screen displays the warning lamps
(in the event of a fault). Braking system warning
lamp
WARNING LAMPS ONTHE INSTRUMENT PANEL
This indicates:
- parking brake applied or not fully
released,
- a n e x c e s s i v e d r o p i n t h e b r a k e fl u - id level, in this case linked with the
STOP warning lamp,
- an electronic brake force distribu- tion malfunction, linked with the
STOP warning lamp.
Seat belt warning lamp
When the ignition is switched on, the
warning lamp comes on if a front oc-
cupant has not fastened or has unfas-
tened their seat belt. The warning lamp is repea-
ted on the instrument panel
screen in the case of the last
2 faults.
Stop immediately in the two latter
cases. Consult a PEUGEOT dealer.
* Suivant destination.
Page 18 of 249
1
20
CHECK (VEHICLE AUTOTEST)
In the presence of a fault
A "minor" fault has been detected:
when the CHECK OK indicator lamp
has been displayed, the warning
lamp(s) is(are) displayed.
You can start your vehicle; however,
contact a PEUGEOT dealer as soon
as possible.
A "major" fault has been detected:
the CHECK OK indicator lamp does
not appear and the warning lamp(s)
is(are) displayed.
Do not start your vehicle.
Call a PEUGEOT dealer without delay.
Automatic CHECK
With the key in the ignition on position,
all of the warning lamps of the func-
tions tested are displayed. They are
switched off after a few seconds.
At the same time, an automatic CHECK
(vehicle autotest) is carried out.
No "major" fault has been de-
tected: the CHECK OK indi-
cator lamp is displayed after
two seconds.
You can start your vehicle.
Pressing the "CHECK/000" button on
the instrument panel starts the manual
CHECK (vehicle autotest).
T h i s f u n c t i o n e n a b l e s y o u t o fi n d o u t , a t
any time (with the key in the ignition on
position or with the engine running):
- the warnings present,
- the status of the functions activated or deactivated (wipers, automatic
illumination of headlamps).
Manual CHECK
The passenger airbag deactiva-
ted indicator lamp * remains on
while the airbag is deactivated.
With the engine running and the ve-
hicle moving, the instrument panel
screen displays the warning lamps
(in the event of a fault). Braking system warning
lamp
WARNING LAMPS ONTHE INSTRUMENT PANEL
This indicates:
- parking brake applied or not fully
released,
- a n e x c e s s i v e d r o p i n t h e b r a k e fl u - id level, in this case linked with the
STOP warning lamp,
- an electronic brake force distribu- tion malfunction, linked with the
STOP warning lamp.
Seat belt warning lamp
When the ignition is switched on, the
warning lamp comes on if a front oc-
cupant has not fastened or has unfas-
tened their seat belt. The warning lamp is repea-
ted on the instrument panel
screen in the case of the last
2 faults.
Stop immediately in the two latter
cases. Consult a PEUGEOT dealer.
* Suivant destination.
Page 24 of 249
1
25
This indicates an automatic
gearbox programme fault.
Automatic gearbox lever position indicators
This indicates an automatic
gearbox malfunction.
4 or 6 speed automatic gearbox
"Park" indicator
"Reverse" indicator
"Neutral" indicator
"Drive" indicator
The letter S or the symbol associat-
ed with the gate lever position indicator
comes on, corresponds to the Sport or
Snow programme selected intentionally.
These correspond to the manual con-
trol of the gearbox, four or six speed.
When the engine speed is too low or
too high in relation for gear engaged,
t h e g e a r s e l e c t e d fl a s h e s f o r a f e w
seconds, then the actual gear is dis-
played, the auto-adaptive programme
having taken control temporarily.
Engine oil temperature gauge
When the ignition is switched on or
while the vehicle is moving, this indi-
cates the engine oil temperature.
When the needle is in zone C , the
temperature is correct.
When the needle is in zone D , the
temperature is too high.
Reduce your speed to lower the tem-
perature. Manual indicator
Page 25 of 249
1
26
SERVICE INDICATOR
This is a visual reminder of when the
next service is due. This service is to
be carried out according to the manu-
facturer's servicing schedule.
Service indicator zero re-set
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
reset button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears .
Once an engine oil level indication has
been displayed, the display indicates
the total and trip distances.
If the service is overdue , each time
the ignition is switched on and for
5 seconds, the distance and the span-
n e r fl a s h .
Example : when the ignition is switched
on and for 5 seconds, the display in-
dicates that the service is overdue by
300 miles/km. The service should be
carried out very shortly.
Once the servicing and oil level infor-
mation has been displayed, the total
distance recorder resumes normal op-
eration and the spanner remains lit.
The point at which a service is due is
calculated using two parameters:
- the total distance travelled,
- the time elapsed since the last ser- vice.
The distance remaining may be
weighted by the time factor, depen-
ding on the user's driving conditions.
Operation
As soon as the ignition is switched on
and for 5 seconds, the spanner sym-
bolising the service operations is lit.
The trip recorder display shows the
d i s t a n c e r e m a i n i n g ( i n r o u n d fi g u r e s )
before the next service.
Example : when switching on the ig-
nition and for 5 seconds, the display
shows that 900 miles/km remain be-
fore the next service is due.
After this operation, if you
wish to disconnect the battery,
lock the vehicle and wait for at
l e a s t fi v e m i n u t e s , o t h e r w i s e
the zero re-set will not be
registered.
Page 26 of 249
1
27
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for approx-
imately 5 seconds, after the service
information. Dipstick
There are 2 level marks on
the dipstick: never exceed
level A .
In position B , top up the
l e v e l v i a t h e o i l fi l l e r c a p ,
using the type of oil suited
to your engine.
A = max.
B = min.
Trip recorder zero reset
Oil level correct
Lack of oil
Flashing indicates a lack of oil which
may damage the engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y c h e c k -
ing with the dipstick, the level must be
topped up. Oil level indicator fault
( fl a s h i n g s e g m e n t s )
Check the oil level using the dipstick.
I f t h e l e v e l i s c o r r e c t , t h e fl a s h i n g i n d i -
cates an engine oil level gauge mal-
function.
Consult a PEUGEOT dealer.
The level observed on the dipstick is
only valid if the vehicle is parked on
level ground and the engine has been
off for more than 15 minutes. The total distance is displayed in
zone A of the display and the trip dis-
tance in zone B .
Distance recorder
With the trip distance displayed, press
the button for a few seconds.
Page 29 of 249
1
29
Range (miles or km)
Current fuel consumption(l/100 or km/l or mpg)
This is the average quantity of fuel con-
sumed during the last few seconds.
This shows the distance that can still
be covered with the fuel remaining in
the tank in accordance with the ave-
rage consumption over the last few
miles (kilometres).
Distance remaining to be travelled (miles or km)
Average speed (mphor km/h)
TRIP menu
Press the
"MENU" button for access
to the main menu.
Select the "Trip computer" or "Ve-
hicle diagnostics" application using
t h e n a v i g a t o r , t h e n c o n fi r m o r p r e s s
the "MODE" button until you gain ac-
cess to the trip computer screen, then
c o n fi r m "OK" .
The "Trip computer" or "Vehicle diag-
nostics" menu offers various options:
- Alerts log,
- Status of the functions,
- Inputting the distance to be tra- velled.
Average fuel consumption(l/100 or km/l or mpg)
Distance travelled (miles or km)
Alerts log
This summarises the active warning
messages, displaying them on the
multifunction screen in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Distance remaining (miles or km)
When guidance is not activated, this
enables you to enter an approximate
distance to be travelled.
T h i s fi g u r e m a y i n c r e a s e i f
there is a change in the style
of driving or the road surface,
p r o d u c i n g a s i g n i fi c a n t d r o p i n
current fuel consumption.
When the range is less than 20 miles
(30 km), four bars are displayed. After
fi l l i n g w i t h f u e l , t h e r a n g e i s d i s p l a y e d
when it exceeds 62 miles (100 km).
If horizontal bars are displayed
for long periods instead of di-
gits, contact a dealer.
This function is displayed only
when the vehicle is travel-
ling at a speed greater than
20 mph (30 km/h). This is the distance remaining to the
destination, either calculated at any
time by the navigation system if gui-
dance is activated or entered by the
user, minus the distance covered since
the distance was entered.
If digits are missing, dashes are dis-
played in their place.
This is the average fuel consumption
since the computer was last set to
zero.
This indicates the distance travelled
since the computer was last set to
zero.
Access via the main menu
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).