instrument panel PEUGEOT 5008 2010 Owners Manual

9
INSTRUMENTS AND CONTROLS

1. Audio and telematics system
steering mounted control stalk.

2. Steering lock and ignition.

3. Wipers/screenwash/trip computer
control stalk.

4. Instrument panel.

5. Driver’s airbag.
Horn.

6. Gear lever.

7. Electric parking brake.

8. 12 V accessories socket.

9. Centre console.

10. Panoramic sunroof control.

11. Handbook storage compartment.

12. Manual headlamp adjustment.
Instrument panel navigator associated with the Peugeot
Connect Media.

13. Alarm button.
Parking sensors button.
Dynamic stability control button (ESP/ASR).

14. Door mirror controls.
Electric window controls.
Child lock.

15. Front door window demist/defrost
vent.

16. Windscreen demist/defrost vent.

16
MONITORING
Instrument panel

A. With the ignition on, the needle should
indicate the level of fuel remaining.

B. With the engine running, its associ-
ated low level warning lamp should
switch off.

C. With the ignition on, the oil level in-
dicator should display "OIL OK" for
a few seconds.
If the levels are not correct, top up the
levels which are low.
24
1. With the ignition on, the orange and
red warning lamps come on.

2. With the engine running, these
warning lamps should switch off.
If warning lamps remain on, refer to the
page concerned.
26
Switch panels
Lighting of the indicator lamp indicates the
status of the corresponding function.

A. Parking space
sensors. 161
78
159
126
122
143
123
145

B. Interior protection
alarm.

C. Visual and audible
parking sensors.

D. ESP OFF.

E. Child lock.

F. Head-up display.

G. Hazard warning
lamps.

H. Distance alert.

Lower

Central
74

I. Central locking.

20
DRIVING SAFELY
Electric parking brake
Manual application/release
The parking brake can be applied manu-
ally by pulling the control A .
When the ignition is on, the parking
brake can be released manually by

pressing the brake pedal and pulling
then releasing the control A . Automatic application/release
Press the accelerator and release the
clutch (manual gearbox), the parking
brake is released automatically and
progressively on acceleration.
With the vehicle stationary, when the

engine is switched off , the parking
brake is applied automatically. Before getting out of the
vehicle, check that the
braking warning lamp
(
red! ) and the warning
lamp P , located in the control A are lit
permanently (not fl ashing).
135
If this warning lamp is lit on the
instrument panel, the automatic
application/release is
deac-
tivated , in this case use the
manual application/release.
When the door is opened with
the engine running an audible
signal is heard, apply the parking
brake manually.
Do not leave a child alone in the ve-
hicle with the ignition on, they could
release the parking brake. If you are towing a trailer or
a caravan or if the gradient is
likely to change (transport by
ship, lorry, towing, ...), apply
the parking brake manually to maxi-
mum force (long pull of control A ) to
immobilise the vehicle.

22
DRIVING SAFELY
Speed limiter "LIMIT"

1. Limiter mode Selection/Off.

2. Decrease the programmed value.

3. Increase the programmed value.

4. Speed limiter On/Off.
The values must be set with
the engine running.
147
Cruise control "CRUISE"

1. Cruise control mode Selection/Off.

2. Programme a speed/Decrease the
programmed value.

3. Programme a speed/Increase the
programmed value.

4. Cruise control Off/Resume.
In order to be programmed or
activated, the vehicle speed
must be higher than 25 mph
(40 km/h), with at least fourth gear
engaged on the manual gearbox
(second gear for the 6-speed elec-
tronic gear control gearbox or auto-
matic gearbox).
149
Display on the instrument panel
The cruise control or speed limiter mode
appears on the instrument panel when
it is selected. Cruise control
Speed limiter

24
INSTRUMENT PANELS
Panel grouping together the vehicle operation indication dials and warning lamps.
Dials

1. Rev counter.
Indicates the engine speed (x 1 000 rpm).

2. Coolant temperature.
Indicates the temperature of the engine coolant (°Celsius).

3. Fuel level.
Indicates the quantity of fuel remaining in the tank.

4. Speedometer.
Indicates the current speed of the moving vehicle (mph or km/h).

5. Screen.

6. Display zero reset or service indi-
cator re-display button.
Resets the selected function to zero (trip distance recorder or service indi-
cator) or displays the service indicator
again.

7. Instrument panel lighting rheostat.
Adjusts the brightness of the lighting of the instruments and controls, if the
vehicle lighting is on.
For more information, refer to
the paragraph relating to the
button or function and its as-
sociated display.

25
Screen(s)
Instrument panel navigator associated with the Peugeot Connect Media
This group of buttons permits:
- when stationary , confi guration of
the vehicle's equipment and the
screen settings (languages, units...),
- while driving , scrolling of the active
functions (trip computer, navigation...). Controls
There are four buttons to control the
large 16/9 screen in the instrument
panel:

1. access the main menu, confi rm the
selection,

2. move up through the menu,

3. move down through the menu,

4. return to the previous display, exit
from the menu.

A. Speed limiter
or
Cruise control.
(mph or km/h)

B. Trip distance recorder.
(miles or km)
C. Service indicator.
(miles or km) or,
Engine oil level indicator.
or
distance recorder.
(miles or km)

D. 6-speed electronic gear control

or automatic gearbox.

E. Warning messages and function
status messages, trip computer,
GPS navigation information, menus
(with
Peugeot Connect Media
).

38
Total distance recorder
System which measures the total dis-
tance travelled by the vehicle during its
life.
Lighting rheostat
System for manual adjustment of the
brightness of the instrument panel in
relation to the exterior brightness.
The total and trip distances are dis-
played for thirty seconds when the ig-
nition is switched off, when the driver's
door is opened and when the vehicle is
locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
since it was reset to zero by the driver.

 With the ignition on, press the button
until zeros appear. Activation
When the vehicle lighting is on:

 press the button to change the
brightness of the instrument panel,

 when the lighting reaches the mini-
mum setting, release the button,
then press again to increase it,
or

 when the lighting reaches the maxi-
mum setting, release the button,
then press again to reduce it,

 when the lighting reaches the level
of brightness required, release the
button. When the vehicle lighting is
on, you cannot switch the in-
strument panel lighting off but
you can adjust it to minimum.
Deactivation
When the lighting is off, or in day mode
on vehicles fi tted with daytime running
lamps, pressing the button does not
have any effect.

52
Monochrome screen C
Instrument panel screen - Peugeot Connect Media
16/9 colour screen - Peugeot Connect Navigation
TRIP COMPUTER
System which provides current in-
formation concerning the trip (range,
consumption…).
Depending on your vehicle's
equipment, the trip computer
information appears on the
multifunction screen or on the instru-
ment panel screen.
Data displays

 Press the button, located at the end
of the wiper stalk , to display the
various trip computer tabs in suc-
cession. With the instrument panel screen
( Peugeot Connect Media )

 Press the up and down arrows on
the navigator, associated with the
Peugeot Connect Media, to display
the various trip computer tabs in
succession.
With the screen C or the colour
screen ( Peugeot Connect Navigation )

53
Trip zero reset

With the screen C or the colour
screen (
Peugeot Connect Navigation
)

 When the trip required is displayed,
press the control for more than
two seconds.
With the instrument panel screen (
Peugeot Connect Media
)

 When the required trip is displayed,
press the "OK" button on the navi-
gator, associated with the Peugeot
Connect Media, for more than
two seconds.
Trips "1" and "2" are independent but
their use is identical.
Trip "1" permits, for example, daily calcu-
lations, and trip "2" monthly calculations.
- The current information
tab with:

94
Windscreen and headlamp wash
B. rear wiper selection ring:
park,
intermittent wipe,
wash-wipe (set duration).
Reverse gear
When reverse gear is engaged, the
rear wiper will come into operation if the
windscreen wipers are operating.
Programming
 Pull the windscreen wiper stalk to-
wards you. The windscreen wash
then the windscreen wipers operate
for a fi xed period.
The headlamp washers only operate
when the dipped
beam
headlamps
are on .
Rear wiper
If a signifi cant accumulation
of snow or ice is present, or
when using a bicycle carrier
on the boot, deactivate the auto-
matic rear wiper via the multifunction
screen confi guration menu. The function is activated or
deactivated via the multi-
function screen confi guration
menu.
This function is activated
by default.
Screenwash/headlamp wash low
In the case of vehicles fi tted with
headlamp washers, when the
minimum level of the reservoir
is reached, this warning lamp is
displayed on the instrument panel, ac-
companied by an audible signal and a
message on the multifunction screen.
Next time you stop, fi ll the screenwash/
headlamp wash reservoir.
The warning lamp is displayed when
the ignition is switched on, or every time
the stalk is operated, until the reservoir
is fi lled.