display PEUGEOT 607 2004 Repair Manual

02-02-2004
DOORS Opening the doors from outside Opening the doors from inside
YOUR 607 IN DETAIL
108
Locking / unlocking from the inside
Ð Using button
Aof the centre con-
sole : This allows the doors, the boot and the fuel filler flap to be locked orunlocked.
Ð Using button B on the door :
¥ on the front doors this allows the doors, the boot and the fuel fillerflap to be locked or unlocked.
¥ on the rear doors this allows the door concerned to be locked orunlocked.
Note : button Bis neutralised if the
vehicle is deadlocked.
' Door open' alert
With the ignition on (2nd notch), withthe engine running or when the vehicle is moving, if a door is not properly closed then the dooropen warning light comes on,accompanied by an audible signaland a diagram indicating the relevant
door on the multi-function display. Child safety This prevents either of the rear doors being opened from inside.
 Turn the switch a quarter of a turn
using the ignition key.

02-02-2004
YOUR 607 IN DETAIL109
Closing the boot lid Press the push button
Cto start
electric closing of the boot lid.Note: do not hinder closing of the
boot lid: any obstacle to closing causes the boot lid to stop and rise a
few centimetres automatically.
When opening or closing the boot,ensure that no-one is close to therear of the vehicle to avoid the risk
of injury.
To close the boot lid manually, useone of the two handles inside theboot lid.
'Boot open' warning With the ignition on (2nd notch), with the engine running or when thevehicle is moving, the door openwarning light comes on, accompa-nied by an audible signal and a dia-
gram on the multi-function display, ifthe boot is not properly closed. Stopping opening or closing of the boot lid While electric opening or closing of the boot lid is in progress, you canstop its movement at any time.
press the push-button Bor Con
the boot lid.
or
press button Aon the remote
control.
When it is stopped, the boot lid isheld in an intermediate position electrically for approximately 10 minutes. After this time, the system switches to standby and releases the boot lid. Note: to leave the intermediate
position, start an electric opening or closing operation or move the boot
lid manually.
THE MOTORISED BOOT Opening the boot
With the vehicle locked / deadlockedPress and hold
button Aof the
remote control key.
This action will also unlock the doors and the fuel filler flap.
Vehicle unlocked
Press and hold button Aof the
remote control key, or press and
hold push-button Bon the boot
lid.
Note: when the vehicle reaches a
speed of 6 mph (10 km/h), the boot locks and the push button Bis
disarmed. It is reactivated when
stationary, by opening a door.

02-02-2004
YOUR 607 IN DETAIL
110
BONNET Opening Pull the lever, located in the driver's footwell, downwards.
 Lift the catch and raise the bonnet.
Bonnet assister struts open the bon-net and keep it open. Closing
 Lower the bonnet and release it at the end of its travel.
 Check that it is locked.
'Bonnet open' warning With the ignition on (2nd notch), with the engine running or when thevehicle is moving, the door openwarning light comes on, accompa-nied by an audible signal and a dia-
gram on the multi-function display, ifthe bonnet is not properly closed.
¥ safety auto-reverse (on sliding only) When the sunroof is closing and meets an obstacle, it stops thenpartially opens again.
In the event of unwanted opening ofthe sunroof on closing, press part B
of the switch until the sunroof is fully
open. As soon as the sunroof stops,press part Aof the switch until the
sunroof is fully closed. The safety auto-reverse function is not operational during this ope-ration. Note: the sunroof shutter is manual.
Always remove the key from the ignition when leaving the vehicle, even fora short time.
In the event of contact when opera-ting the sunroof, you must reverse
the movement of the sunroof. To dothis, press the switch concerned. When the driver operates the sun- roof switch, he must ensure that noone is preventing correct closing ofthe sunroof. The driver must ensure that passengers use the electric sunroof
correctly. Be aware of children when operating the sunroof.
SUNROOF Control the sunroof:- manually: lightly press the switch;
the roof stops as soon as the switch is released.
- automatically: press the switch
down fully; the roof opens or closescompletely depending on where theswitch is pressed.
¥ to partially open the roof: press
part Aof the switch. To close it,
press part B of the switch.
¥ to open the roof completely:press part Bof the switch.
¥ to close it completely: press part
A of the switch.

02-02-2004
YOUR 607 IN DETAIL
114
Do not cover the rain sensor located on thewindscreen behind the
interior mirror.
When using an automatic carwash, switch off the ignition orcheck that the wiper stalk is not inthe automatic position.
In winter, it is advisable to wait until the windscreen is completelyfree of ice before operating theautomatic wipe.
WINDSCREEN
WIPER STALK
Windscreen wipers 3 Fast wipe
2 Normal wipe
1 Automatic wipe
0 Off
When the ignition has been switched off for more than aminute with the control in a wipeposition (1, 2 or 3), it is necessaryto reactivate this function. To d o
this, move the stalk to any position,then move it back to the requiredposition. Maintenance position This position enables the wiper blades to be removed.
In the minute following switching off of the ignition, any action on the stalkpositions the wipers in the centre ofthe windscreen so that they may becleaned or replaced.
To park the wipers after this has been done, switch on the ignitionand operate the stalk.
Windscreen and headlamp wash Pull the windscreen wiper stalk towards you. The windscreen wash then the wind- screen wipers operate for a fixedperiod. The windscreen wash and headlamp wash operate simultaneously for twoseconds,
only if the headlamps are
on .
Screenwash/headlamp wash low
When the minimum level of the reservoir is reached, thiswarning light comes on,accompanied by an audiblesignal and the message
'Screenwash low' on the multi-func-
tion display. Next time you stop, fill the screen-
wash / headlamp wash reservoir.
If the reservoir is empty, the warning light comes on when the ignition isswitched on, or every time the stalkis operated, until the reservoir isfilled.

02-02-2004
YOUR 607 IN DETAIL
114
Do not cover the rain sensor located on thewindscreen behind the
interior mirror.
When using an automatic carwash, switch off the ignition orcheck that the wiper stalk is not inthe automatic position.
In winter, it is advisable to wait until the windscreen is completelyfree of ice before operating theautomatic wipe.
WINDSCREEN
WIPER STALK
Windscreen wipers 3 Fast wipe
2 Normal wipe
1 Automatic wipe
0 Off
When the ignition has been switched off for more than aminute with the control in a wipeposition (1, 2 or 3), it is necessaryto reactivate this function. To d o
this, move the stalk to any position,then move it back to the requiredposition. Maintenance position This position enables the wiper blades to be removed.
In the minute following switching off of the ignition, any action on the stalkpositions the wipers in the centre ofthe windscreen so that they may becleaned or replaced.
To park the wipers after this has been done, switch on the ignitionand operate the stalk.
Windscreen and headlamp wash Pull the windscreen wiper stalk towards you. The windscreen wash then the wind- screen wipers operate for a fixedperiod. The windscreen wash and headlamp wash operate simultaneously for twoseconds,
only if the headlamps are
on .
Screenwash/headlamp wash low
When the minimum level of the reservoir is reached, thiswarning light comes on,accompanied by an audiblesignal and the message
'Screenwash low' on the multi-func-
tion display. Next time you stop, fill the screen-
wash / headlamp wash reservoir.
If the reservoir is empty, the warning light comes on when the ignition isswitched on, or every time the stalkis operated, until the reservoir isfilled.

02-02-2004
YOUR 607 IN DETAIL115
Automatic windscreen wiper In position
1, the wiper operates
automatically and adjusts its speed
to the intensity of the rainfall. Operating check Activation
The indicator light comes on, accompanied by an audiblesignal, as soon as the driversets the windscreen wiperstalk to position 1.
Neutralisation When the function is neu-tralised, going from position 1
to another position, the indi-cator light comes on, accom-panied by an audible signal.
In cases of malfunction , the driver
is informed by the message 'Rain
sensor fault' on the multi-function
display.In position 1, the windscreen wiper
will operate on intermittent wipe.
Contact a PEUGEOT dealer to havethe system checked.

02-02-2004
Monochrome screenC
Ð the 'vehicle' tab with:
¥ current range and consumption,
Ð tab '1' (route 1) with:
¥ the average consumption, the distance driven and the average speed calcu- lated over route ' 1',
Ð tab '2' (route 2) with the same features.
Zero re-set When the required route is displayed, press the button for more than four seconds.
116
YOUR 607 IN DETAIL
THE TRIP COMPUTER
Pressing the button located at the end of the windscreen wiper controldisplays
in turn: Colour screen
Ð
'Route 1' with:
¥ the route number, ¥ the time which has elapsed since the last zero re-set of the route,
¥ the average speed, ¥ the average consumption,¥ the distance travelled
Ð 'Route 2' with the same features.
The following information is displayed simultaneously at the bottom of thescreen:
Ð the distance that remains to be travelled,
Ð the current range,Ð the current consumption. Zero re-set When the required route is displayed, press the button for more than twoseconds.

02-02-2004
117
Range This shows the distance that can still be covered with the fuel remaining inthe tank. Note: this figure may rise if there is a
change in driving style or road sur- face, causing a significant drop incurrent fuel consumption. Average consumption This is the average fuel consumption since the computer was last set tozero.Distance travelled This indicates the distance travelled since the computer was last set tozero.
YOUR 607 IN DETAIL
Current consumption This is the average fuel consumption during the last few seconds. This function is displayed only when the vehicle is travelling at a speedgreater than 20 mph (30 km/h).
Average speed This is the average speed calculated since the computer was last set tozero (with the ignition on).
The routes Routes 1 and 2 are independent but have identical application. Route 1, for example, allows you to make daily calculations, and route2 monthly calculations. On this page, the illustration on the left represents the mono-
chrome screen C display, the oneon the right the colour screen
display.
After re-setting the trip computer to zero, the range data become signifi-cant only after a few seconds of use. If horizontal segments are displayed for long periods instead of digits,
contact a PEUGEOT dealer.

02-02-2004
Monochrome screenC
Ð the 'vehicle' tab with:
¥ current range and consumption,
Ð tab '1' (route 1) with:
¥ the average consumption, the distance driven and the average speed calcu- lated over route ' 1',
Ð tab '2' (route 2) with the same features.
Zero re-set When the required route is displayed, press the button for more than four seconds.
116
YOUR 607 IN DETAIL
THE TRIP COMPUTER
Pressing the button located at the end of the windscreen wiper controldisplays
in turn: Colour screen
Ð
'Route 1' with:
¥ the route number, ¥ the time which has elapsed since the last zero re-set of the route,
¥ the average speed, ¥ the average consumption,¥ the distance travelled
Ð 'Route 2' with the same features.
The following information is displayed simultaneously at the bottom of thescreen:
Ð the distance that remains to be travelled,
Ð the current range,Ð the current consumption. Zero re-set When the required route is displayed, press the button for more than twoseconds.

02-02-2004
117
Range This shows the distance that can still be covered with the fuel remaining inthe tank. Note: this figure may rise if there is a
change in driving style or road sur- face, causing a significant drop incurrent fuel consumption. Average consumption This is the average fuel consumption since the computer was last set tozero.Distance travelled This indicates the distance travelled since the computer was last set tozero.
YOUR 607 IN DETAIL
Current consumption This is the average fuel consumption during the last few seconds. This function is displayed only when the vehicle is travelling at a speedgreater than 20 mph (30 km/h).
Average speed This is the average speed calculated since the computer was last set tozero (with the ignition on).
The routes Routes 1 and 2 are independent but have identical application. Route 1, for example, allows you to make daily calculations, and route2 monthly calculations. On this page, the illustration on the left represents the mono-
chrome screen C display, the oneon the right the colour screen
display.
After re-setting the trip computer to zero, the range data become signifi-cant only after a few seconds of use. If horizontal segments are displayed for long periods instead of digits,
contact a PEUGEOT dealer.