display Peugeot 607 Dag 2002 Workshop Manual

Page 102 of 167

Electronic engine immobiliser
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre
vents starting of the vehicle by any
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly, the central locking button
indicator light, situated on the centre
console, flashes rapidly when the
ignition is switched on (2nd notch).
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon
as possible. Flat battery
(CR 2025/3 volt battery)
This is indicated by illumination of a
warning light on the instrument panel
display, accompanied by an audible
signal and a message on the multi
function display.
Contact a PEUGEOT dealer to
replace the battery.
YOUR 607 IN DETAIL
102
Key in ignition
A buzzer sounds on opening the dri
ver's door, if the key has been left in
the ignition. Locating your car
To locate your car in a car park:
 press button A; the courtesy lights
come on and the direction indica
tors flash for a few seconds.
Programming the
remote control
in the key  Switch off the ignition.
 Switch the ignition on again.
 Immediately press button A.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control
key is now working again.
Confidential card
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.

Page 104 of 167

Electronic engine immobiliser
This locks the engine control system
a few moments after the ignition has
been switched off and therefore pre
vents starting of the vehicle by any
one who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly, the central locking button
indicator light, situated on the centre
console, flashes rapidly when the
ignition is switched on (2nd notch).
WARNING: your vehicle is no longer
protected in this event.
Contact a PEUGEOT dealer as soon
as possible. Flat battery
(CR 2025/3 volt battery)
This is indicated by illumination of a
warning light on the instrument panel
display, accompanied by an audible
signal and a message on the multi
function display.
Contact a PEUGEOT dealer to
replace the battery.
YOUR 607 IN DETAIL
102
Key in ignition
A buzzer sounds on opening the dri
ver's door, if the key has been left in
the ignition. Locating your car
To locate your car in a car park:
 press button A; the courtesy lights
come on and the direction indica
tors flash for a few seconds.
Programming the
remote control
in the key  Switch off the ignition.
 Switch the ignition on again.
 Immediately press button A.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control
key is now working again.
Confidential card
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.

Page 107 of 167

Child safety
This prevents either of the rear doors
being opened from inside. Turn the red plastic switch a quar
ter of a turn using the ignition key.
YOUR 607 IN DETAIL 105
DOORS
Opening the doors
from outside
Opening the doors
from insideLocking / unlocking from the
inside
– Using button
Aof the centre con
sole :
This allows the doors, the boot and
the fuel filler flap to be locked or
unlocked.
– Using button B on the door :
• on the front doors this allows the doors, the boot and the fuel filler
flap to be locked or unlocked.
• on the rear doors this allows the door concerned to be locked or
unlocked.
Note : button Bis neutralised if the
vehicle is deadlocked.
' Door open' alert
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, if a door is not proper
ly closed then the door open warning
light comes on, accompanied by an
audible signal and a diagram indicat
ing the relevant door on the
multi–function display, if a door is not
properlyclosed.

Page 108 of 167

Vehicle unlocked
 Press and hold button Cof the
remote control key or press push
button A.
Note: pushbutton Acan be deacti
vated. Rotate control B,located
inside the boot lid, a quarter of a turn
(anticlockwise) using the key.
YOUR 607 IN DETAIL
106
THE BOOT
Opening the boot
With the vehicle locked / deadlocked

Press and hold button Cof the
remote control key.
This action will also unlock the doors
and the fuel filler flap. SUNROOF
Control the sunroof:
– manually
: lightly press the switch;
the roof stops as soon as the
switch is released.
– automatically : press the switch
down; the roof opens partially or
opens or closes completely
depending on where the switch is
pressed.
– to partially open the roof: press
part Aof the switch. To close it,
press part Bof the switch.
– to open the roof completely: press part Bof the switch.
– to close it completely: press part
A of the switch .
– safety autoreverse When the sunroof is closing and
meets an obstacle, it stops then
opens again.
Note: the sunroof shutter is manual.
Closing the boot
 Press the centre of the boot lid
with both hands, until it locks.
'Boot open' warning
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, the door open warning
light comes on, accompanied by an
audible signal and a diagram on the
multifunction display, if the boot is
not properly closed.

Page 109 of 167

The engine and the ignition must
be switched off when filling with
fuel : Open the fuel filler flap by press
ing its front right hand edge,
 Unscrew the cap and hook it over
the tab located on the inside of the
flap.
When filling up your tank, do not con
tinue after the 3rd cutoff of the
pump; this could cause your vehicle
to malfunction.
The capacity of the tank is approx
imately 80 litres.  After filling the tank, screw the cap
on fully and close the flap.
Fuel filler cap open When this light comes on,
accompanied by an audible
signal and the message
'Fuel cap open' on the dis
play, screw the cap on again
and close the fuel filler flap.
YOUR 607 IN DETAIL 107
BONNET
Opening
 Pull the lever, located in the dri
ver's footwell, downwards.
 Lift the catch and raise the bon
net.
Bonnet assister struts open the bon
net and keep it open.
Closing
 Lower the bonnet and release it at
the end of its travel.
 Check that it is locked.
'Bonnet open' warning
With the ignition on (2nd notch), with
the engine running or when the vehi
cle is moving, the door open warning
light comes on, accompanied by an
audible signal and a diagram on the
multi–function display, if the bonnet
is not properly closed. FILLING WITH FUEL
Low fuel level
When the minimum fuel
level is reached, this warn
ing light comes on, accom
panied by an audible signal
and the message 'Fuel
level low' on the multifunction dis
play.
You can can still drive approxi
mately 30 miles (50 km) without
filling up with fuel.
Filling with fuel
Locking and unlocking of the fuel
filler flap, the doors and the boot is
simultaneous (except when selective
unlocking is initialised; in this case
press the unlocking button of the
remote control again).

Page 112 of 167

110
Screenwash/headlamp wash lowWhen the minimum level of
the reservoir is reached,
this warning light comes on,
accompanied by an audible
signal and the message
'Screenwash low' on the multi
function display.
Next time you stop, fill the screen
wash / headlamp wash reservoir.
If the reservoir is empty, the warning
light comes on when the ignition is
switched on, or every time the stalk
is operated, until the reservoir is
filled.
YOUR 607 IN DETAIL
WINDSCREEN
WIPER STALK
Windscreen wipers
3 Fast wipe
2 Normal wipe
1 Intermittent or automatic wipe
0 Off
When the ignition has been
switched off for more than a
minute with the control in a wipe
position (1, 2 or 3), it is necesary
to reactivate this function. To d o
this, move the stalk to any position,
then move it back to the required
position. Windscreen and headlamp wash
Pull the windscreen wiper stalk
towards you.
The windscreen wash then the wind
screen wipers operate for a fixed
period. The windscreen wash and
headlamp wash operate simultane
ously for a few seconds,
only if the
dipped beam or main beam head
lamps are on. Do not cover the rain
sensor located on the
windscreen behind the
interior mirror.
When using an automat
ic car wash, switch off the ignition
or check that the wiper stalk is not
in the automatic position.
In winter, it is advisable to wait
until the windscreen is completely
free of ice before operating the
automatic wipe.
Maintenance position
This position enables the wiper
blade to be removed.
In the minute following switching off
of the ignition, any action on the stalk
positions the wipers in the centre of
the windscreen so that they may be
cleaned or replaced.
To park the wipers after this has
been done, switch on the ignition
and operate the stalk.

Page 113 of 167

111
YOUR 607 IN DETAIL
Automatic windscreen wiper
In position 1, the wiper operates
automatically and adjusts its speed
to the intensity of the rainfall. Operating check
Activation
The indicator light comes on,
accompanied by an audible
signal, as soon as the driver
sets the windscreen wiper
stalk to position 1.
Neutralisation When the function is neu
tralised, going from position 1
to another position, the indi
cator light comes on, accom
panied by an audible signal.
In cases of malfunction, the driver
is informed by the message 'Rain
sensor faulty' on the multifunction
display.
In position 1, the windscreen wiper
will operate on intermittent wipe.
Contact a PEUGEOT dealer to have
the system checked.

Page 114 of 167

112YOUR 607 IN DETAIL
THE TRIP COMPUTER
Pressing the button located at the end of thewindscreen wiper controldisplays
in turn: Colour screen

'Route 1' with:
• the route number,
• the time which has elapsed since the
last zero reset of the route,
• the average speed,
• the average consumption,
• the distance travelled
– 'Route 2' with the same features.
The following information is displayed
simultaneously at the bottom of the
screen:
– the distance that remains to be travelled,
– the current range,
– the current consumption.
Zero reset
When the required route is displayed,
press the button for more than two
seconds.
Monochrome screen C
– the 'vehicle' index with:
• current range and consumption,
– index '1' (route 1) with:
• the average consumption, the distance driven and the average speed calcu
lated over route ' 1',
– index '2' (route 2) with the same features.
Zero reset
When the required route is displayed, press the button for more than four
seconds.

Page 115 of 167

113
Range
This shows the distance that can still
be covered with the fuel remaining in
the tank.
Note: this figure may rise if there is a
change in driving style or road sur
face, causing a significant drop in
current fuel consumption. Average consumption
This is the average fuel consumption
since the computer was last set to
zero.Distance travelled
This indicates the distance travelled
since the computer was last set to
zero.
YOUR 607 IN DETAIL
Current consumption
This is the average fuel consumption
during the last few seconds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average speed
this is the average speed calculated
since the computer was last set to
zero (with the ignition on).
The routes
Routes 1 and 2 are independent but
have identical application.
Route 1, for example, allows you
to make daily calculations, and route
2 monthly calculations.
On this page, the illustration on
the left represents the mono
chrome screen C display, the one
on the right the colour screen
display.
After resetting the trip computer to
zero, the range data become signif
icant only after a few seconds of
use.
If horizontal segments are displayed
for long periods instead of digits,
contact a PEUGEOT dealer.

Page 116 of 167

Specific features of the colour
screen
'Trip computer' context menu
Briefly press the 'MODE' button to
select one of the following functions:
– Route 1,
– Route 2,
– Enter the distance to the destina tion (when guidance is not activat
ed; otherwise the information is
given by the navigation),
– Change the units (°C or °F, km and
litres or miles and gallons).
Time elapsed since the last zero
reset of the route
This is the time which has elapsed
since the last zero reset of the route
displayed. The time is calculated,
depending on the circumstances, by
the number of 'hours' and 'minutes',
'days' and 'hours' or 'months' and
'days'. Distance remaining to be travelled
This is the distance remaining to the
destination. It can either be calculat
ed by the navigation if guidance is
activated, or entered by the user,
minus the distance covered since
the distance was entered.
At the start of the journey, the dis
tance to be travelled is given by:
– the satellite navigation system, if
guidance has been activated,
– the user entering the distance to the destination.
Note: if digits are missing, dashes
are displayed in their place.
YOUR 607 IN DETAIL
114

Page:   < prev 1-10 ... 11-20 21-30 31-40 41-50 51-60 61-70 next >