remote control Peugeot 607 Dag 2002 Owner's Manual

Page 2 of 167

3YOUR AT A GLANCE
1Lights and direction indica
tors stalk.
2 Steering wheel adjustment.
3 Driver's front air bag.
Horn.
4 Instrument dials.
5 Windscreen wash/wipe
stalk.
Trip computer stalk.
6 Audio remote control stalk.
7 Hazard warning lights
switch.
8 Central adjustable
heating/ventilation vents and
air flow regulation.
9 Sunshine / brightness
sensor.
10 Windscreen demisting
vents.
11 Passenger air bag.
12 Glove compartment.
13 Side adjustable heating/ven
tilation vents and air flow
regulation. 14
Door window demisting
vent.
15 Passenger air bag disarming
switch.
16 Front seats heating switch.
17 Rear ashtray.
Rear lighter.
Rear seats heating switch.
18 Rear footwell heating vent.
19 Twoposition armrest with
compartments.
20 Handbrake.
21 Electronically controlled sus
pension switch.
Doors and boot locking
switch.
Sunroof switch.
Rear blind switch.
22 Front ashtray.
Front lighter.
23 Gear lever.
24 RM2 audio system or RT2
audio/telephone system with
PEUGEOT call button. 25
Heating/ventilation controls.
26 Multifunction display.
27 Steering lock and ignition.
28 Fuse box.
29 Speakers location.
30 Electric mirror controls.
Window controls.
Rear window locking control.
31 Headlamp height adjust
ment.
32 ESP disarming switch.
33 Alarm button.
34 Cruise control.
35 Memory buttons for:
Front seat settings
Electric mirror settings

Page 3 of 167

YOUR AT A GLANCE4
THE REMOTE CONTROL
KEY
From the driver's door, the key
allows you to lock or unlock the
doors, the boot and the fuel filler
flap, as well as to fold back or
open out the exterior mirrors.
The remote control in the key
provides the same function at a
distance.
Locking with the remote
control  Press button A.
This is confirmed by fixed lighting
of the direction indicators for
approximately two seconds.
Unlocking with the remote
control key  Press button B.
This is confirmed by rapid flash
ing of the direction indicators. With the vehicle unlocked, the
boot is opened using the push
button located on the right rear
side, in the '
zero' of the 607
badge.
Opening the boot with the
remote control key  Keep button Cpressed.
Key in ignition
If you leave the key in the
ignition, this is indicated by a
buzzer upon opening the
driver's door.
Locating the vehicle
To locate your vehicle in a car
park, press button A; the cour
tesy lights come on and the
direction indicators flash for
approximately twenty seconds.
Driving position memorised
by the remote control key
When locking the doors, the
remote control key memorises
the position of the driver's seat
and the driving mirrors.
Each remote control key mem
orises a specific setting.
When unlocking the doors, the
driver's seat and the driving mir
rors assume the position memo
rised by the remote control key, if
this position has been changed in
the meantime. Note:
do not press the buttons of
your remote control key out of
range of your vehicle as there is
a risk that you could render it
inoperative. It would then be nec
essary to reprogramme it.
Deadlocking
This renders the internal and
external door locking controls
inoperative and permits the auto
matic closing of the windows and
the sunroof.
With the key: lock the vehicle and keep the
key in the locked position for
approximately one second.
With the remote control:  press button Ato lock the
vehicle (the direction indicator
lights remain on for approxi
mately two seconds),
 within five seconds, press but
ton Aagain to deadlock the
vehicle (the direction indicator
lights remain on for approxi
mately two seconds).
101

Page 9 of 167

14
FUEL FILLER FLAP
Opening / Closing:
Locking and unlocking of the fuel filler
flap, the doors and boot is simultane
ous (except when selective unlocking
is initialised; in this case press the
unlocking button of the remote control
once).
FILLING WITH FUEL
This must be carried out with the engine and the ignition switched
off.
A hook is provided inside the fuel filler flap to hold the filler cap.
A label affixed to the inside of the fuel filler flap i nforms you which fuels
are authorised or prohibited.
The tank capacity is approximately 80 litres.
When the minimum level of the tank is reached, this light come s
on, accompanied by an audible signal and the message 'Fuel
level low' on the multifunction display.
You have enough fuel to drive approximately
30 miles (50 km).
OPENING THE BONNET
From inside:
pull the handle downwards.
From outside:
lift the catch and raise the
bonnet.
YOUR AT A GLANCE
107107

Page 32 of 167

INSTRUMENTS AND CONTROLS
36
Antilock braking system (ABS) warning light
This is linked to the warning light on the instrument pane
l.
Display of this warning light is accompanied by an audible si gnal and the message 'ABS faulty' on the multifunc
tion display.
If the warning light remains on, or comes on at over 8 mph (12 km/h), this indicates a malfunction of the ABS.
However, the vehicle retains conventional servoassisted braking.
Contact a PEUGEOT dealer.
Automatic headlamp adjustment warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Automatic adjustment of
headlamps faulty' on the multifunction display.
It comes on if there is a malfunction of the system.
Contact a PEUGEOT dealer. Automatic gearbox fault warning light
Display of this warning light is accompanied by an audible si gnal and the message 'Automatic gearbox faulty' on
the multifunction display.
It comes on if there is an abnormality in the automatic gearbo x.
The gearbox will continue to operate in downgrade mode (lo cked in 3rd gear).
Contact a PEUGEOT dealer. Tyre underinflation detector battery flat / remote control ba ttery flat / impact sensor fault / wheel(s) miss
ing warning light
Display of this warning light is accompanied by an audible si gnal and a message on the multifunction display show
ing the cause of the warning:
– 'Tyre pressure sensor battery charge low',
– 'Remote control battery charge low',
– 'Impact sensor faulty',
– 'X tyre pressure sensor(s) missing'.
Contact a PEUGEOT dealer.

Page 61 of 167

TELEPHONE: Audio/Telephone RT2
This function is a GSM 900 MHZ telephone incorporated in the audio system.
It possesses a 'hands free'function, provided by a microphone located in the front courte sy light and a steering column
remote control which allows access to most of the functions.
It also possesses a 'confidential' function, provided by the instrument panel located in the u pper casing of the centre front
armrest.
Note: An echo may be heard for a few seconds at the beginning of t he call.
The principal "mobile"type functions are shown on the display incorporated in the a udio system; the menu lists can be
referrred to on the multifunction display.
This function is active when the ignition key is in the accessories position (1st notch), the ignition is switched on (2nd notch),
the engine is running or the vehicle is being driven.
Note: when the ignition key is in the accessories position (1st notch) or the ignition is switched on (2nd notch), this function
will be interrupted after thirty minutes, when the message 'Economy mode active'appears on the multifunction display. If
you are using the telephone at that time, you will be ab le to finish your call.
General information about the display (Audio/Telephone R T2 display)
In telephone mode, the display shows the following informa tion, where applicable.
1. Network signal indicator (3 levels).
2. Service indicator not available.
3. Indicates a communication in progress.
4. Indicator showing connection to an outside network.
5. Indicates:
– when continuously lit: presence of an unread message or message s.
– when flashing: the message tape is full.
6. Display zone (10 symbols x 2 lines).
YOUR 607 IN DETAIL
62

Page 62 of 167

Selecting telephone mode / Entering a number / Switching off the microphone
To change to telephone mode, press the 'TEL' button or for more than 2 seconds on the steering column
remote control.
Insert your SIM card fully into the slot at the front (use only t he new generation 3V SIM card with bank card
format).
Note: the SIM card must not be taken out while the audio/telepho ne system is still in use. If you forget to do this, an audi
ble signal will sound for a few seconds after the ignition is switched off.
Enter your PIN number and confirm with the 'OK' button in order to access the network. The welcome screen is
displayed.
Note: the PIN code is erased each time the ignition is switched off , but the ''PIN code protection'' function may be
cancelled.
Enter the number of the person you wish to speak to on the di gital keypad and pres the 'OK'button to make the call.
To switch off the microphone midcommunication, press the 'TEL'button.
Cancelling the PIN code request
To cancel the PIN code request, select 'PIN code protection' in the 'Telephone parameters' menu and confirm; select 'OFF'
and confirm, then input your PIN code and confirm.
Receiving / Ending a call
When a ringing sounds to let you know that a call is waiti ng, you can choose either to accept it by press
ing the 'OK'button or not to accept it by pressing button Por by selecting 'Refuse call' using the steer
ing column remote control, pressing the end to confirm.
If you do not accept it, the call is diverted to your voice mai l (if this service is available and active).
To end the call, press button Por the end of the steering wheel remote control.
Note: Not accepting or ending a call by means of the steering whee l control returns the system to radio mode.
Receiving two incoming calls
During a call, when there is another incoming call, you are i nformed of this by a ring and a message. You may choose:
– to accept the call by pressing button 2 then "OK"; the first caller is put on hold and you are in contact wit h the second.
However, pressing button 2 again allows you to return to th e first caller,
– to finish the call you are on and talk to the second call er by pressing button 1 then "OK",
– not to accept the new call by pressing button "C".
YOUR 607 IN DETAIL 63

Page 64 of 167

Services
This menu gives direct access.
Press button O to display the "Services" menu and make a selection from the following three menus, the n validate by press
ing the end of the steering wheel remote control:
– ''Emergency call''* to automatically send a call containing a minimessage (SMS) which a llows you to be identified and
located; vocal communication is established with the help cent re,
– ''Technical assistance''* for contacting the call centre controlling the PEUGEOT breakdown service,
– ''Peugeot Service"* to contact directly the PEUGEOT customer contact centre and access the services offered.
IMPORTANT: as is the case for all telephones, your onboard telephone op erates using cellular and terrestrial networks.
Because of this, connection cannot be guaranteed in all cases.
Selecting a directory
To consult the various directories, insert your SIM card and input t he PIN code.
To access the 'Directories' menu, press the 'MAN'button or press the end of the steering wheel remote
control.
Make a selection from the three directories available: DIRECTORY (SIM), LAST NUMBERS CALLEDor TEL (PEUGEOT
customer contact centre).
Storing numbers
Last numbers called: your phone stores in the memory the five last numbers called or whi ch were used to call you.
To access these numbers, press the 'OK' button or the end of the steering column remote control and scroll
through these numbers using buttons Mand Lor the knob of the steering column remote control. Then, if
you want to call one of these numbers, press the 'OK' button, or the end of the steering column remote con
trol.
Telephone directory (SIM): this can store around eighty numbers (if more than 80 numbers are st ored on the SIM card
used, only the first 80 will be accessible).
YOUR 607 IN DETAIL 65
* If option and service available.

Page 65 of 167

YOUR 607 IN DETAIL
66
Storing numbers in the telephone directory (SIM)
In the 'Phonebook' menu, validate the 'New Entry' function with the 'OK'button.
Using the alphanumerical keypad input the name, telephone number and address (the memory number) or keep the one
suggested. Confirm each operation with the 'OK'button.
To access a number in the memory: – look for and select it in the menu 'Find by name'or 'Find by address ' of the 'PHONEBOOK' menu and
press the 'OK'button to make the call,
– or press the end of the steering wheel remote control for more than two seconds, look for and select the
number, then press the end of the remote control to make the call,
– or enter the memory number using the keypad, then press button Ffollowed by the 'OK' button to make the
call.
Note: the first nine numbers in this list are directly accessible. Hold one of the nine buttons of the keypad down, then press
the 'OK' button to call.
Selecting the previous item of a menu Press button Mas many times as necessary to select the required item. Confirm with the 'OK' button.
Selecting the following item of a menu Press button Mas many times as necessary to select the required item. Validate wi th the 'OK' button.
Accessing mini messages
In telephone mode: when the buzzer sounds and the 'envelope' symbol is displayed o n the screen, you can access new
messages by pressing the 'MAN' button.
In radio mode: when the symbol appears, you must change to telephone mode (pre ss the "TEL" button) to be able to
access the new messages.
Note: the old stored messages are accessible. In the 'SMS'menu, confirm the 'Messages received' function with the 'OK'
button, then select the message using button 'M'or 'L' to consult it.

Page 93 of 167

YOUR 607 IN DETAIL95
Memorising using the buttons
To memorise:
 Place the ignition key in the 'run
ning' position (2nd notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off  Briefly press button 1 or 2to recall
the corresponding memorised
position. The end of the setting is
indicated by a bleep.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running
 Keep button 1 or 2pressed down
until the bleep indicates the end of
setting of the corresponding
memorised position.
Memorising seat
and mirror positions
Four driving positions can be memo
rised:
– two, using two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front and rear heated seats
controls
 Press the switch. The tempera
ture is regulated automatically.
 Press it again to stop operation.
Note: the command to activate heat
ing of the seat(s) remains in the
memory for two minutes after the
ignition is switched off.

Page 95 of 167

YOUR 607 IN DETAIL95
Memorising using the buttons
To memorise:
 Place the ignition key in the 'run
ning' position (2nd notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off  Briefly press button 1 or 2to recall
the corresponding memorised
position. The end of the setting is
indicated by a bleep.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running
 Keep button 1 or 2pressed down
until the bleep indicates the end of
setting of the corresponding
memorised position.
Memorising seat
and mirror positions
Four driving positions can be memo
rised:
– two, using two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front and rear heated seats
controls
 Press the switch. The tempera
ture is regulated automatically.
 Press it again to stop operation.
Note: the command to activate heat
ing of the seat(s) remains in the
memory for two minutes after the
ignition is switched off.

Page:   1-10 11-20 next >