stop start Peugeot 607 Dag 2002 Owner's Manual

YOUR AT A GLANCE5
STARTING
STOP position:
The ignition is switched off.
1st notch, Accessories position:The ignition is switched off but
the accessories still function.
2nd notch, Running position:
The ignition is on.
Starting position:
Operates the starter.
Starting a diesel engineIf the temperature is highenough, the preheat
indicator light does not
come on and you can
start immediately.
If the indicator light comes on,
wait for it to go out before operat
ing the starter.
If the engine stalls, it is neces
sary to return the key to the
'Stop' position before restarting. CHECK
(vehicle autotest)
Automatic check
With the ignition on (2nd notch)
If no malfunction has been
detected: In the absence of
vehicle function status indi
cator lights, the OK light is
displayed after two seconds
on the instrument panel screen.
Otherwise, it will be displayed after
these indicator lights come on.
If a 'minor' malfunction has been
detected: the warning light for the
faulty function is displayed on the
instrument panel screen. Certain
indicator lights showing the status of
vehicle functions may also come on,
followed by the OKindicator light.
If a 'major' malfunction has been
detected: the corresponding warn
ing light is displayed on the instru
ment panel screen. Certain indicator
lights showing the status of vehicle
functions may also come on. The
OK indicator light does not come
on. Do not start your vehicle.
Contact a PEUGEOT dealer.
Afterwards, if the passenger air
bag is disarmed, the correspond
ing warning light will come on.
With the engine running or if the
vehicle is moving, the instrument
panel screen temporarily displays:
– lights indicating warnings, when
these occur,
– vehicle function sta tus indicator lights,
when a change
occurs.
The display of certain indicator
lights is accompanied by an audi
ble signal and a message on the
multifunction display.
MANUAL CHECK  Press the "CHECK" button on the
instrument panel.
With the ignition key in the accessories
position, with the ignition switched on,
with the engine running or the vehicle
moving, this function informs you at all
times of the following:
– any current warnings,
– the status of functions which it is possible to switch on or switch off
(windscreen wipers, automatic
switching on of lights, cruise con
trol, disarming of passenger air
bag, etc.).
The corresponding warning lights are
displayed in succession on the instru
ment panel screen.
If a warning or a change of status
occurs during the CHECKmode, the
corresponding indicator light(s) will be
displayed at the end of this mode.
Never run the engine in
a confined space.
Do not make any modi fications to the steering
lock.
31

INSTRUMENTS AND CONTROLS
30
INDICATOR LIGHTS
With the key in the accessories position (1st notch): the batte
ry charge warning light illuminates on the instrument panel display.
With the ignition on (2nd notch): the following three warning lights illuminate on the sides of the instrument panel:
Brake fluid level and brake force distribution fault warning light.
This light should go out after 3 seconds.
If the warning light remains on, or if it comes on when the engine is running and the vehicle is moving, it indicates
an excessive drop in the brake fluid level or a malfunction of the brake force distribution.
Stop immediately. Contact a PEUGEOT dealer.
Antilock braking system (ABS) warning light
This should go out after 3 seconds.
If the warning light remains on or comes on above 8 mph (12 km/h ), this indicates a malfunction of the ABS.
However, the vehicle retains conventional servoassisted braking.
Contact a PEUGEOT dealer.
Engine diagnostics warning light
This should go out 3 seconds after the engine starts.
If it flashes with the engine running, this indicates a ma lfunction in the injection or the ignition system. There is a
risk of damage to the catalytic converter (petrol engine only).
If it is on continuously, this indicates a fault in the e mission control system.
Contact a PEUGEOT dealer as soon as possible.
At the same time, on the instrument panel display: If no malfunction has been detected: the OK light comes on after two seconds (following a black screen), in t he
absence of indicator lights showing the status of vehicle fun ctions. If these indicator lights are present, the OKbut
ton will come on after these. You may start your vehicle.
If a 'minor' malfunction has been detected: the warning light for the faulty function comes on. Certain indicator
lights showing the status of vehicle functions may also come on, followed by the OKindicator light. You can start
your vehicle; however, contact a PEUGEOT dealer as soon as possible.
If a 'major' malfunction has been detected: the corresponding warning light comes on. Certain indicator li ghts showing
the status of vehicle functions may also come on. The OKindicator light does not come on. Do not start your vehicle.
Contact a PEUGEOT dealer.
Afterwards, if the passenger air bag is disarmed, the co rresponding indicator light will come on.

INSTRUMENTS AND CONTROLS
32
STOP warning light
This comes on after the
engine oil pressure, coolant temperature orpuncture warning lights, to which it is linked.
Stop immediately. Contact a PEUGEOT dealer.
Brake fluid level and brake force distribution fault warn ing light
This is linked to the light on the instrument panel.
Display of this warning light accompaned by an audible signa l and the message 'Brake fluid low'indicates an
excessive drop in the brake fluid level.
Display of this warning light, accompanied by an audible sig nal and the message 'Braking system faulty' on the multifunc
tion display indicates a malfunction of the brake force distrib ution system.
Stop immediately in both cases. Contact a PEUGEOT dealer.
Dynamic stability control (ESP/ASR) warning light
Display of this warning light, accompanied by an audible sig nal and the message 'ESP/ASR system faulty' on the
multifunction display indicates a system malfunction.
Contact a PEUGEOT dealer.
Handbrake warning light
Display of this warning light, accompanied by an audible sig nal (vehicle moving) and the message 'Handbrake on'
on the multifunction display, indicates that the handbrake is applied or has not been released correctly.
Battery charge warning light
This comes on each time the ignition key is in the accessories posi tion (1st notch).
Display of this warning light when the engine is running is accompanied by an audible signal and the message 'Bat
tery charge fault' on the multifunction display.
This can indicate:
– faulty operation of the charging circuit,
– loose battery or starter terminals,
– a cut or slack alternator belt,
– an alternator fault.
Contact a PEUGEOT dealer.

CD CHANGER: Audio RM2 and RT2 Selecting CD changer mode.
Press buttonD.
Selecting a disc
Press one of the buttons '1' to '6' to select the corresponding disc
RT2
RM2
Selecting a track Press button Mto select the next track.
Press button Lto return to the start of the current track or to select the previ ous track.
Accelerated play
Press and hold button Mor Lfor forwards or backwards accelerated play.
Accelerated play stops as soon as the button is released.
Shuffle (RDM) When the CD changer is selected, press and hold button D for 2 seconds. The tracks will be played in ran
dom sequence (pressing button Dfor longer allows other discs to be played in random sequence). Pressing
button D again returns you to normal play.
YOUR 607 IN DETAIL
60

YOUR 607 IN DETAIL91
Manual adjustment Y
ou may, if you wish, make a differ
ent selection from the one offered by
the system, by manually modifying a
setting.
 Pressing the 'AUTO'driver or
passenger button enables you to
return to the corresponding auto
matic operation.
6 Adjustment ofthe driver's air
distribution
7 Adjustment of the passenger's
air distribution
 Pressing the dri
ver's or passenger's
button several times in
succession allows you to position the
air flow on the driver's or passen
ger's side, towards:
– the windscreen and the feet,
– the feet,
– the centre vent, the side ventand the feet,
– the centre vent and the side vent,
– the windscreen. Note:
when programme 5(following
page) is being used, button 7does
not operate; it causes temporary
flashing of the button 5indicator
light.
8 Air conditioning (A/C) on/off
 Press this button
once to stop the air
conditioning.
The symbol 'A/C'goes out.
 Press this button again to return to
automatic air conditioning.
The symbol 'A/C' comes on.
5 Visibility
programme
In certain cases, the
comfort programme
may prove inadequate
to demist or deice the
windows (humidity,
many passengers, ice).
 In this situation, select the visibili
ty programme for rapid clearing of
the windows.
It manages the air conditioning and
the air flow and intake and distrib
utes the ventilation towards the
windscreen and the side windows.
The symbols 'A/C', 'AUTO' and air
flow (fan) are displayed.
Note: for your comfort, between two
starting operations the settings are
retained if the temperature of the
passenger compartment has not var
ied a great deal. If it has, automatic
mode is used.

YOUR 607 IN DETAIL95
Memorising using the buttons
To memorise:
 Place the ignition key in the 'run
ning' position (2nd notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off  Briefly press button 1 or 2to recall
the corresponding memorised
position. The end of the setting is
indicated by a bleep.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running
 Keep button 1 or 2pressed down
until the bleep indicates the end of
setting of the corresponding
memorised position.
Memorising seat
and mirror positions
Four driving positions can be memo
rised:
– two, using two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front and rear heated seats
controls
 Press the switch. The tempera
ture is regulated automatically.
 Press it again to stop operation.
Note: the command to activate heat
ing of the seat(s) remains in the
memory for two minutes after the
ignition is switched off.

YOUR 607 IN DETAIL95
Memorising using the buttons
To memorise:
 Place the ignition key in the 'run
ning' position (2nd notch),
 Adjust your seat and mirrors,
 Press button M,then button 1
(first driving position) or button 2
(second driving position) within
four seconds.
An audible signal confirms that a
position has been memorised.
Memorising a new position cancels
the previous one.
Recalling a memorised position
Engine off  Briefly press button 1 or 2to recall
the corresponding memorised
position. The end of the setting is
indicated by a bleep.
Note: after recalling a memorised
position five times in succession, the
function will be cancelled until the
engine is started.
Engine running
 Keep button 1 or 2pressed down
until the bleep indicates the end of
setting of the corresponding
memorised position.
Memorising seat
and mirror positions
Four driving positions can be memo
rised:
– two, using two remote control
keys (two users),
– two, using buttons M/1 and M/2.
Driving positions memorised by
the remote control key
When locking the doors, the remote
control key memorises the position
of the driver's seat and the exterior
mirrors.
When unlocking the doors, the dri
ver's seat and the exterior mirrors
resume the position memorised by
the remote control key if this has
changed in the meantime.
Each remote control key can
memorise a specific setting. Front and rear heated seats
controls
 Press the switch. The tempera
ture is regulated automatically.
 Press it again to stop operation.
Note: the command to activate heat
ing of the seat(s) remains in the
memory for two minutes after the
ignition is switched off.

YOUR 607 IN DETAIL103
Make a careful note of the number on each key. The key number i
s coded on the label attached to the key. If
the key is lost, your PEUGEOT dealer can rapidly supply you with ne w keys.
The highfrequency remote control key is a highperformance system.
Do not operate it while it is in your pocket as there is a p ossibility that it may unlock your vehicle without your
knowledge.
The remote control cannot operate if the key is in the ignit ion, even if the ignition is switched off, except for
reprogramming.
Do not operate the deadlock if there is someone inside the vehicle.
As a safety measure (when there are children on board), remove the i gnition key when leaving the vehicle, even for a
short time.
Do not handle the buttons of your remote control when out of range of your vehicle as you run the risk of stopping it from
working. It would then be necessary to reprogramme the remote cont rol.
When buying a secondhand car:
– Ensure that you are given the confidential card;
– Have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones
which can start your vehicle.
Do not make any modifications to the electronic engine immobil iser system.

YOUR 607 IN DETAIL103
Make a careful note of the number on each key. The key number i
s coded on the label attached to the key. If
the key is lost, your PEUGEOT dealer can rapidly supply you with ne w keys.
The highfrequency remote control key is a highperformance system.
Do not operate it while it is in your pocket as there is a p ossibility that it may unlock your vehicle without your
knowledge.
The remote control cannot operate if the key is in the ignit ion, even if the ignition is switched off, except for
reprogramming.
Do not operate the deadlock if there is someone inside the vehicle.
As a safety measure (when there are children on board), remove the i gnition key when leaving the vehicle, even for a
short time.
Do not handle the buttons of your remote control when out of range of your vehicle as you run the risk of stopping it from
working. It would then be necessary to reprogramme the remote cont rol.
When buying a secondhand car:
– Ensure that you are given the confidential card;
– Have the key codes memorised by a PEUGEOT dealer, to ensure that the keys in your possession are the only ones
which can start your vehicle.
Do not make any modifications to the electronic engine immobil iser system.

Aflat battery prevents
the engine from starting.
PRACTICAL INFORMATION
150
CHANGING A WINDSCREEN
WIPER BLADE
Placing the wiper blades in the
maintenance position
 Less than one minute after switch
ing off the ignition, activate the
windscreen wiper stalk to position
the blades in the centre of the
windscreen (maintenance posi
tion).
Replacing a blade  Lift the arm, then unclip the blade
and remove it.
 Fit the new blade and fold down
the arm.
To park the blades, switch on the
ignition and operate the wind
screen wiper stalk.
ECONOMY MODE FUNCTION
After the engine has stopped, certain
functions (windscreen wiper, electric
windows, sunroof, rear electric blind,
electric seats, audio equipment, tele
phone etc) can only be used for thir
ty minutes, to prevent discharging
the battery.
Once the thirty minutes are over, the
message "Economy mode active"
appears on the multi–function dis
play and the active functions are put
on standby.
REMOVING A MAT
When removing a mat on the driver's
or passenger's side, push back the
seat as far as possible and remove
the clips.
To remove a rear mat, push the cor
responding front seat forward and
remove the clip.
On refitting, position the mat and
press firmly to refit the securing clips.
LOAD REDUCTION
When driving, certain functions
(heated rear screen, heating system
for passenger compartment of diesel
vehicles, etc.) may be switched off
temporarily, depending on the level
of battery charge.
Reactivation of the functions on
standby is automatic, as soon as the
battery permits.
These functions are automatically
reactivated next time the vehicle is
driven.
Note:
if the telephone is being used
when economy mode starts, it will
still be possible to finish the call.