Peugeot 607 Dag 2006 Owner's Guide

1INSTRUMENTS AND CONTROLS
31
The distance remaining before the
next service is less than 500 miles
(1.000 km).
Each time the ignition is switched on
and for 7 seconds, the service span-
ner and the distance flash.
Example: 400 miles (900 km) remain
before the next service is due.
When switching on the ignition and for
7 seconds, the display shows:
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the service
spanner remains lit.
This indicates that a service should be
carried out shortly. The display shows
the total and trip distances. 7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the symbol
remains lit. The display shows the total
and trip distances.
Note:
the service spanner may also
be lit if the two-year interval has been
exceeded. Service indicator zero re-set
The service is overdue.
Each time the ignition is switched on
and for 7 seconds, the symbol and the
excess distance flash.
Example: the service is overdue by
300 miles/km. The service should be
carried out very shortly.
When the ignition is switched on and
for 7 seconds, the display shows:
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as fol-
lows:
 Switch off the ignition,
 Press and hold the trip recorder re-
set button,
 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" and the
service symbol disappears, release
the button.
Important: after this opera-
tion, if you wish to disconnect
the battery, lock the vehicle
and wait for at least five min-
utes, otherwise the zero re-set will not
be registered.

1INSTRUMENTS AND CONTROLS
31
The distance remaining before the
next service is less than 500 miles
(1.000 km).
Each time the ignition is switched on
and for 7 seconds, the service span-
ner and the distance flash.
Example: 400 miles (900 km) remain
before the next service is due.
When switching on the ignition and for
7 seconds, the display shows:
7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the service
spanner remains lit.
This indicates that a service should be
carried out shortly. The display shows
the total and trip distances. 7 seconds after the ignition is switched
on, the total distance recorder resumes
normal operation and the symbol
remains lit. The display shows the total
and trip distances.
Note:
the service spanner may also
be lit if the two-year interval has been
exceeded. Service indicator zero re-set
The service is overdue.
Each time the ignition is switched on
and for 7 seconds, the symbol and the
excess distance flash.
Example: the service is overdue by
300 miles/km. The service should be
carried out very shortly.
When the ignition is switched on and
for 7 seconds, the display shows:
Your PEUGEOT dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as fol-
lows:
 Switch off the ignition,
 Press and hold the trip recorder re-
set button,
 Switch on the ignition.
The display begins a countdown.
When the display shows "=0" and the
service symbol disappears, release
the button.
Important: after this opera-
tion, if you wish to disconnect
the battery, lock the vehicle
and wait for at least five min-
utes, otherwise the zero re-set will not
be registered.

1INSTRUMENTS AND CONTROLS
32
Trip recorder zero reset button Lighting rheostat button
With the ignition on, press the button
until the zeros appear. With the headlamps on, press button
B
to increase the brightness of the light-
ing of the instruments and controls or
button A to reduce it.
As soon as the lighting reaches the
required level of brightness, release
the button.

1INSTRUMENTS AND CONTROLS
33
TRIP COMPUTER
Each press on the button, located at
the end of the wipers stalk, displays
different trip computer data in succes-
sion, depending on the multifunction
display: - the
"vehicle" tab with:
• the range, the current consumption and the distance remaining to be
travelled,
- tab "1" (route 1) with:
• the average speed, the average consumption and the distance trav-
elled calculated over route "1",
- tab "2" (route 2) with the same char-
acteristics for a second route.
Colour screen C Colour and map screen DT
- the "Current info" with:
• the range, the current consumption and the distance remaining to be
travelled,
- "Route 1" with:
• the distance travelled, the aver- age consumption and the average
speed calculated over route "1",
- "Route 2" with the same character-
istics for a second route.

1INSTRUMENTS AND CONTROLS
34
Range (km or miles)
This shows the distance that can still
be covered with the fuel remaining in
the tank in accordance with the aver-
age consumption over the last few
miles (kilometres).
This figure may increase if there is a
change in the style of driving or the
road surface, producing a significant
drop in current consumption.
When the range is less than 30 miles
(50 km), four dashes are displayed.
After filling with fuel, the range is
displayed when it exceeds 62 miles
(100 km).
If dashes are displayed for long periods
instead of digits, contact a PEUGEOT
dealer.
Current consumption
(l/100 or km/l or mpg)
This is the average quantity of fuel con-
sumed during the last few seconds.
This function is displayed only when
the vehicle is travelling at a speed
greater than 20 mph (30 km/h).
Average consumption
(l/100 or km/l or mpg)
This is the average fuel consumption
since the computer was last set to
zero.
Distance travelled
(km or miles)
This indicates the distance travelled
since the computer was last set to
zero.
Distance remaining to be
travelled (km or miles)
This is the distance remaining to be
travelled to the final destination. It is
either calculated by the navigation sys-
tem if guidance is activated or entered
by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
Average speed (km/h or mph)
This is the average speed calculated
since the computer was last set to
zero (with the ignition on).The routes
"1" and "2" are independ-
ent but have identical application.
Route "1" for example allows you to
make daily calculations and route "2"
monthly calculations.
The routes
Zero reset
When the required route is displayed,
press the end of the wipers stalk for
more than two seconds.

1INSTRUMENTS AND CONTROLS
35
Warnings log
This summarises the active warning
messages, displaying them on the
multifunction display in succession.
Status of the functions
This summarises the active or inactive
status of the functions present on the
vehicle.
Inputting the distance remaining to
be travelled
When guidance is not activated, this
enables you to enter an approximate
distance to the final destination.Access via the general menu
C screen
DT screen
"TRIP" menu
Press the "MENU" or "TRIP" button
to gain access to the general menu.
Select the "Trip computer" applica-
tion using the navigator, then confirm.
The "Trip computer" menu offers vari-
ous options:
- Inputting of the distance to be trav- elled,
- Warnings log,
- Status of the functions. The different trip computer data also
appears on the instrument panel dis-
play at the same time.
Indication on the instrument
panel display

2MULTIFUNCTION DISPLAYS
36
COLOUR SCREEN C
This displays the following informa-
tion, via the RD4 audio equipment
control pad:
- the time,
- the date,
- the exterior temperature (the value displayed flashes if there is a risk of
ice),
- the accesses check,
- the vehicle functions warning or sta- tus messages, displayed temporar-
ily,
- the audio sources displays,
- the trip computer displays,
- the personalisation and configura- tion displays,
- the hands-free kit displays. Management of the displays
Example: "TRIP"
General menu
Press the
"MENU" button to gain
access to the general menu and
select one of the following functions:
- "Audio functions",
- "Trip computer",
- "Personalisation-Configuration",
- "Telephone". "Personalisation-Configuration"
menu
This provides access to successive
confirmation windows.
Defining the vehicle parameters
This enables you to activate or deac-
tivate certain driving and comfort ele-
ments:
- "Automatic switching on of the
lights",
- "Follow-me-home lighting" and "Duration",
- "Remote control action",
- "Permanent locking of the boot".
The
"AUDIO" , "TRIP" and "TEL" but-
tons on the RD4 audio equipment con-
trol pad permit displaying in the main
window.
Example: "Audio functions" Example: "Automatic switching on of
the lights"

2MULTIFUNCTION DISPLAYS
37
Selection of the language
German, Spanish, French, English,
Italian, Dutch, Portuguese and
Brazilian Portuguese.
Configuration of the display
- "Setting the brightness-video".
- "Setting the date and time".
- "Selection of the units":• temperature (°C or °F),
• fuel consumption (l/100, mpg or km/l).
- "Selection of the colours". Changing the date and time
From the
general menu , select the
" P e r s o n a l i s a t i o n - C o n fi g u r a t i o n "
icon using the navigator, then confirm.
From the list displayed, select
"Configuration of the display" , then
confirm.
From the list displayed, select "Setting
the date and time" , then confirm. Set the parameters one by one:
- the zone selected is displayed on the
screen,
- use the navigator to move from one zone to another,
- your new parameters are confirmed one by one, by pressing the naviga-
tor button,
- all of the changes are saved, if you click on "OK" on the screen, or can-
celled, if you press the "ESC" button
on the control pad.
For safety reasons, configura-
tion of the multifunction dis-
plays by the driver must be
carried out while stationary.
The brightness of the display
and of the instrument panel
may change when the lights
are switched on automatically.

2MULTIFUNCTION DISPLAYS
38
DT COLOUR AND
MAP SCREEN
This displays the following informa-
tion, via the RT3 GPS audio/telephone
control pad:
- the time,
- the date,
- the exterior temperature (the value displayed flashes if there is a risk of
ice),
- the accesses check,
- the vehicle functions warning or sta- tus messages, displayed temporar-
ily,
- the audio sources displays,
- the telematic systems displays (tel- ephone, services, ...),
- the trip computer displays,
- the personalisation and configura- tion displays,
- the satellite navigation system dis- plays. General menu
Press the
"MENU" button to gain
access to the general menu and
select one of the following functions:
- "Navigation - Guidance",
- "Audio functions",
- "Trip computer",
- "Personalisation-Configuration",
- "Directory",
- "Telematics",
- "Map",
- "Video". "Personalisation-Configuration"
menu
This provides access to successive
confirmation windows.
The brightness of the display
and of the instrument panel
may change when the lights
are switched on automatically.

2MULTIFUNCTION DISPLAYS
39
Configuration of the display
- "Selection of the colours": selection of the colours available for the dis-
play.
- "Brightness and brilliance".
- "Sound": selection of the sound ambi- ence, setting of the voice synthesiser
and of the voice commands.
- "International parameters": • setting of the date and time,
• selection of the units: temperature (°C or °F) and fuel consumption
(l/100, mpg or km/l).
- "Selection of the language": German, Spanish, French, English, Italian,
Dutch, Portuguese and Brazilian
Portuguese. "Video" menu
Defining the vehicle parameters
This enables you to activate or deac-
tivate certain driving and comfort ele-
ments:
- "Automatic switching on of the
lights",
- "Follow-me-home lighting" and "Duration",
- "Remote control action",
- "Permanent locking of the boot".
You can connect video equipment
(camcorder, digital camera, DVD
player, ...) to the three video sockets
located in the glove box.
Video display is only possible when
stationary.
Select the "Video" menu from the gen-
eral menu:
- "Activate video mode" to activate/ deactivate the video,
- "Video parameters" to set the display format, the brightness, the contrast
and the colours.
Pressing the "DARK" button discon-
nects the video display.
Successive presses of the "SOURCE"
button permit the selection of an audio
source other than that of the video.
For safety reasons, configura-
tion of the multifunction dis-
plays by the driver must be
carried out while stationary.
Example: "Automatic switching on of
the lights"