tow PEUGEOT 807 2002.5 Owners Manual

YOUR 807 AT A GLANCE10STEERING WHEEL STALKS
LIGHTING
Front and rear lights (ring A)Lights off.
Side lights on.Dipped / main
beam headlamps
on.
Automatic
switching on of
lights. Automatic switching on of
lights
To activate or disarm this func
tion, place the key in the acces
sories position, the lighting stalk
in position
0 and press for more
than two seconds on the end of
the stalk.
Front fog lamps and rear fog
lamps (ring B)
Front fog lamps (1 st
rota
tion of the ring forwards).
Front fog lamps
and rear fog
lamps (2 nd
rotation
of the ring for
wards).
To switch off: rotate the push ring
B rearwards. WINDSCREEN WIPERS
Front
2 Rapid wipe
1 Normal wipe
l Intermittent wipe
or
AUTO Automatic wipe
0 Stop
Single wipe
Washwipe: pull the stalk towards you.
Automatic wipe
In the AUTO position, a
rain sensor controls the
automatic operation of
the wipers. The wipers
adapt their speed to
the intensity of the
rainfall.
Rear
Stop Intermittent W ash
wipe wipe
11 2
11 4
18-11-2002

YOUR 807 AT A GLANCE13
AUTOMATIC GEARBOX "PORSCHE TIPTRONIC SYSTEM"
The four speed automaticgearbox offers a choice between the comfort of
automatic integral regulation enhanced by a snow programme , or the
pleasure of manual gear changing.
Gear selection gate  Move the lever in the gate to select one of the functions.
Once the function is selected, the indicator light for that function is dis
played on the instrument panel screen.
: snow programme.
P ark: to park or to start the engine, with the handbrake on or off.
R everse:to reverse(select this function with the vehicle stationary and the
engine at idle).
N eutral: to start the engine or to park, with the handbrake on.
Note: if position Nis engaged by mistake
while the car is moving, allow the engine
to return to idling speed before engaging
function Dto accelerate.
D rive: for automatic gear changing.
M anual: for manualgear changing.
To change the four gears manually:
 Push the lever to the + symbol to
change up to the next gear and pull the
handle towards the – symbol to
change down to the next gear.
Note: the
(snow) programme do
esnot
operate when in manual mode. Moving Off
With the engine running, to move
off from position
P:
 It is essential to press the
brake pedal to exit positionP
 Select the function required R,
D or M, then gradually release
the pressure on the brake
pedal; the vehicle will move off
immediately.
You can also move off from posi
tion N:
 Release the handbrake, with
your foot on the brake.
 Select function R, D or M then
gradually release the pressure
on the brake pedal; the vehi
cle will move off immediately.
When the engine is idling with
the brakes not applied, if function
R, D or Mis selected, the vehicle
moves without the accelerator
being pressed.
For this reason, do not leave
children unattended inside the
car, with the engine
running.
132
18-11-2002

PEUGEOT SERVICING Your vehicle's servicing schedule is based on level Aservices (engine oil change, checks and topups) and level Cservices
( level A + workshop operations carried out every 40,000/36,000 miles (60 00 0 km)) in accordance with the tables on the fol
lowing pages.
Irrespective of the conditions in which your vehicle is used, the interval between two level Aservices may not exceed:
• For petrol engines, 20,000 miles (30 000 km) or 2 years .
• For HDI turbo diesel engines, 12,000 miles (20 000 km) or 2 years .
In all cases, the extension of the service intervals mea ns that the engine oil level must be checked regularly: top
ping up of the oil between oil changes is normal.
It is for this reason that your PEUGEOT dealer invites you to make an intermediate visit between each service. The
service indicator does not indicate when this visit is d ue.
This visit is to be made between two services.
A Peugeot professional will carry out a quick check and will top up the levels if necessary (oil, coolant, screenwash up to
2 litres).
If the oil level is too low there is a risk of serious d amage to the engine: check the engine oil level at least every
3,000 miles (5 000 km)
This extended servicing has been made possible by modifications t o our vehicles and to the lubricants:
THUS IT IS ESSENTIAL TO ONLY USE ENGINE LUBRICANTS THAT ARE APPROVED AND RECOMMEN DED BY THE
MANUFACTURER (see "Lubricants" pages).
Arduous conditions of use
If the vehicle is used in certain particularly arduous condition s such ascontinuous doortodoor use, town use (e.g. taxi),
repeated short journeys, with the engine cold in low tem peraturesor for long stays in hot countries with temperatures
often above 30 °C , cold countrieswith temperatures often below minus 15 °C, countries with a dusty atmosphere, and
countries whose lubricantsor fuels do not conform to our recommendations.
It is necessary to follow an "Arduous conditions" servicing schedule w hich includes special operations and shorter service
intervals:
• Every 12,000 miles (20 000 km) or every year for petrol vehicles.
• Every 10,000 miles (15 000 km) or every year for HDI Turbo Diesel en gine vehicles.
PEUGEOT SERVICING
18
18-11-2002

YOUR 807 IN DETAIL77
The main "Navigation Guidance"
menu offers various options for acti
vation or management of guidance:
– choice of the type of destination address (entering of address, ser
vice, GPS coordinates, stored
address),
– modification to the initial route (entering of a diversion)
– displaying of the details of the itin erary (displaying of the chosen
destination)
– management of the guidance options (setting of the guidance
tool parameters),
– stop or resume guidance (display ing of the message which changes
depending on the previous status).
Navigation Guidance
The
"Select a destination" menu
offers various options for reaching a
destination:
– entering a postal address,
– selecting a service available in a town (town hall, hotel, cinema, air
port...),
– entering GPS details,
– selecting a destination stored in the directory,
– selecting one of the last ten desti nations.
Selecting a destinationThe last guidance address is dis
played.
Select and validate in succession the
entry zones
"Town","Street" , then
"N" to fill them in.
The "OK" function permits validation
of the address and access to the
guidance activation function.
The "Archive" function permits
recording of the address in a directory
file.
The "Current location" function
permits display of the current
address.
Entering an address
18-11-2002

YOUR 807 IN DETAIL
78
Entering the first letter of the name of
the town required will erase that of
the town displayed.
To enter the name of another town,
select each letter by turning the dial,
then validate each letter by pressing
the dial.
If an error is made entering the let
ters, the "Correct" function permits
erasing of the last letter entered.
Note: following the validation of a
letter, only those which could make
up a name existing in the database
appear.
As letters are entered, the "List"
function indicates the number of
towns beginning with the same let
ters. Activation of this function per
mits selection of a town from the list. When the list contains fewer than
five names, these are displayed
automatically. Select a town then
validate by pressing the dial.
When the complete name of the
town is displayed, select the
"OK"
function then confirm by pressing the
dial.
Note: once the town has been
entered, you can confirm by pressing
"OK" . You will then be guided to the
centre of this town automatically.
Entering the name of the street
Enter the name of the street in the
same way as the name of the town.
When the full name of the street is
displayed, select the "OK"function
then confirm by pressing the dial.
Entering the name of the town
Enter the number of the street previ
ously entered.
Select the
"OK"function, then con
firm by pressing the dial.
Note: if the number of the street
entered is not available, it is rejected.
You can also select a street from the
"Junctions" function, which avoids
having to enter the street number.
Note: if the street selected does not
have a number, the list of junctions is
displayed automatically.
The full destination is displayed.
Select the "OK" function, then
confirm by pressing the dial to
access the guidance activation
function.
Follow the instructions given by
the system.
Entering the number of the street
or junction
18-11-2002

YOUR 807 IN DETAIL79
The most recent destinations are
shown.
There are three possible methods of
defining the location to which you
wish to travel:
accept the last details input by means of the "OK"function,
input the details of your destina tion,
automatically input the details of your current location by means of
the "Current location" function.
GPS details
The last address entered is displayed.
There are three options for defining
the location in which you wish to
obtain this service:
accept the last address entered
using the "OK"function,
fill in the "Town" and "Street"
zones,
automatically enter the name of your current location using the
"Current location" function.
Selecting a service
If you wish to be directed to a ser
vice, select the
categorycorre
sponding to the service , then confirm
by pressing the dial.
The list of services corresponding to
the category selected is displayed.
Select the servicethen confirm by
pressing the dial to access the
"Place choice" function.
An indication on the edge of the screen
(x/n) shows you the maximum number
of establishments providing the same
service within a radius of 50 km, as the
crow flies, from the selected location.
Use buttons "<"and ">"to consult the
list provided.
When the establishment of your choice
is displayed, you can:
selelct the "OK"function to activate
guidance towards this service,
select the "Archive" function to enter
this establishment in your directory.
Note:
if the service selected is not avail
able in the programmed location, a tem
porary message informs you of this.
Following validation of the location, the
service closest to it is displayed. The
distance indicated is the distance as the
crow flies from the service to the selected
location.
18-11-2002

The contextual menu associated with
the "Navigation Guidance" applica
tion appears as a superimposed display,
when this is the application currently in
use in the main screen window.
This menu is limited to the following
functions:
changing of the initial route (entering of a diversion),
switching to "Selection Movement on map" mode*,
storing of the current location (postal address if available or, if it is not, the
GPS coordinates),
changing of the route calculation criteria,
stopping or resuming of guidance (displaying of the message which
changes depending on the previous
status).
General notes on the "Map"
application*
The map guidance can be displayed
in two ways:
full screen map,
reduced size map on the righthand side and zoom image of the
junction on the lefthand side.
To switch from one to the other,
press the dial for more than two sec
onds.
The "Map" application has two oper
ating modes: "Selection Movement on
map"** mode,
"Vehicle following on map"
mode.
A "Zoom" function enables you to
enlarge the map around the selected
point, in accordance with the eleven
preset levels relating to the following
scales:
100 m/cm, 200 m/cm, 500 m/cm,
1 km/cm, 2 km/cm, 5 km/cm,
10 km/cm, 20 km/cm, 50 km/cm,
100 km/cm, 200 km/cm.
This is achieved by turning the dial. This mode permits:
selection of any point on the map
to obtain guidance towards it or to
obtain information about it (postal
address if available or, if it is not,
GPS coordinates),
lateral movement on the map by means of the four directional
arrows, representing the four cardi
nal points (North, East, South,
West),
zooming in on the map in accor dance with the eleven preset
levels,
displaying of the "Map" contextual
menu.
YOUR 807 IN DETAIL
82
"Navigation Guidance"
contextual menu
"Selection Movement on map"
mode**
18-11-2002

The contextual menu associated with
the "Navigation Guidance" applica
tion appears as a superimposed display,
when this is the application currently in
use in the main screen window.
This menu is limited to the following
functions:
changing of the initial route (entering of a diversion),
switching to "Selection Movement on map" mode*,
storing of the current location (postal address if available or, if it is not, the
GPS coordinates),
changing of the route calculation criteria,
stopping or resuming of guidance (displaying of the message which
changes depending on the previous
status).
General notes on the "Map"
application*
The map guidance can be displayed
in two ways:
full screen map,
reduced size map on the righthand side and zoom image of the
junction on the lefthand side.
To switch from one to the other,
press the dial for more than two sec
onds.
The "Map" application has two oper
ating modes: "Selection Movement on
map"** mode,
"Vehicle following on map"
mode.
A "Zoom" function enables you to
enlarge the map around the selected
point, in accordance with the eleven
preset levels relating to the following
scales:
100 m/cm, 200 m/cm, 500 m/cm,
1 km/cm, 2 km/cm, 5 km/cm,
10 km/cm, 20 km/cm, 50 km/cm,
100 km/cm, 200 km/cm.
This is achieved by turning the dial. This mode permits:
selection of any point on the map
to obtain guidance towards it or to
obtain information about it (postal
address if available or, if it is not,
GPS coordinates),
lateral movement on the map by means of the four directional
arrows, representing the four cardi
nal points (North, East, South,
West),
zooming in on the map in accor dance with the eleven preset
levels,
displaying of the "Map" contextual
menu.
YOUR 807 IN DETAIL
82
"Navigation Guidance"
contextual menu
"Selection Movement on map"
mode**
18-11-2002

YOUR 807 IN DETAIL83
This mode permits:
displaying of the vehicle on the map with the route proposed by
the navigation if the guidance is
active,
zooming in on the map in accor dance with the eleven preset
levels,
displaying of the "Navigation
Guidance" contextual menu.
"Vehicle following on map" mode
From the
general menu , the main
"Map" menu offers various options
for guidance management:
switching to "Selection Movement on map" mode**,
direction of the map towards the North or in the direction of the
vehicle,
recentering of the map around the vehicle when it has disappeared **,
opening of the services selection window visible on the map,
displaying of the window for enter ing the description for recording
the current position of the vehicle
in a directory file.
Map*The contextual menu associated
with the
"Map"application and with
the "Selection Movement on
map" mode appears as a superim
posed display, when these are in use
in the main screen window.
This menu is limited to the following
functions:
displaying of the information on the location selected on the map,
selection of a location on the map as a destination,
storing of the location selected (postal address if available or, if it
is not, GPS coordinates, so that
they can be recorded in a directory
file),
switching to "Vehicle following on map" mode.
* DT colour screen only.
** During the year.
"Map" contextual menu**
18-11-2002

YOUR 807 IN DETAIL
92
4 12V socket
You have a 12V accessory socket at
the foot of the driver's seat, which is
accessible to passengers in the
2
nd
row.
5 Front and rear armrests
To place the armrest in its rest
position:
– Lift the armrest until it is is aligned with the seat back.
To place the armrest in the position
in which it is used:
– Push it towards the rear.
– Fold it down completely.
– Raise it slowly to the required position.
– If you lift it past the required position, restart the above operations.
To remove it occasionally:
– Lift the armrest, going past the idle position.
– press its securing pin firmly and tilt it fully.
– Pull towards you to remove it from its fixing.
To put it back in place:
– place it in its removal position.
– Push as far as the fixing allows.
FRONT SEAT LAYOUT
1 Storage drawers
There is a storage drawer under
each front seat.
– To open it, lift and pull.
– To take it out, open it to its full
extent, press the ends of the slides
and lift it, then remove it complete
ly.
Note: under the seat on the passen
ger side, if the vehicle has an ampli
fier, it will not be possible to use the
storage drawer. 2 Retaining elastic straps
There is an elastic retaining strap on
each front seat, on the centre side.
– In the side position (elastic strap
on your own seat), this can be
used as a magazine holder.
– In the transverse position (elastic straps hooked between the two
seats), it can hold a bag.
3 'Aviation' type table
You have an 'aviation' type table fitted
with a can holder, fitted to each front
seat.
Do not forget to fold this before
pivoting the seat.
Note: each front seat also has a
pocket for money on the seat back
18-11-2002