warning PEUGEOT 807 2002 User Guide

INSTRUMENTS AND CONTROLS31
Passenger air bag disarming indicator light
This comes on for a few seconds each time the ignition is switch ed on.
Illumination of this indicator light is accompanied by an au dible signal and the message"Passenger air bag
disarmed" on the multifunction display.
If the passenger air bag is disarmed, the indicator light comes on when the ignition is switched on and remains on.
In all cases, if the indicator light flashes, contact a PEUGEOT dealer.
Front, side and curtain air bags warning light
This warning light comes on when the ignition is switched o n.
Illumination of this warning light, with the engine run ning, is accompanied by an audible signal and the message
"Air bag fault" on the multifunction display, indicating a front, side or cu rtain air bag fault.
Contact a PEUGEOT dealer.
Driver's seat belt warning light
With the engine running, this indicator light comes on, acco mpanied by an audible signal at a speed above 6 mph
(10 km/h) and the message "Seat belt not fastened" on the multifunction display, if the driver's seat belt is no t
fastened.
Low fuel level warning light
This light comes on each time the ignition is switched on.
When the warning light comes on, accompanied by the message "Fuel level low"on the multifunction display,
there is enough fuel remaining to drive approximately 30 miles (50 km). The tank capacity is approximately 80 litres.
This light flashes to indicate a malfunction of the fuel gauge or cuttingoff of the fuel supply, if it is accompanie d by the
message "Fuel circuit neutralised" on the multifunction display.
Restore the supply (refer to the "Practical Information § Fuel Su pply CutOff" section) or contact a PEUGEOT dealer,
depending on the circumstances.
Note: some functions can be configured by your PEUGEOT dealer.
18-11-2002

INSTRUMENTS AND CONTROLS
32
In zoneA,the temperature is correct.
In zone B, the temperature is too high. The central STOPwarning light and the
maximum coolant temperature warning light 1come on, accompanied by an
audible signal and the message "Coolant temp. too high"on the multifunction
display.
You must stop immediately.
Warning : wait for the engine to cool before topping up the le vel.
The cooling system is pressurised.
In the event of a breakdown and in order to avoid any risk of scalding, unscrew
the cap two turns to allow the pressure to drop.
When the pressure has dropped, remove the cap and top up the level.
Contact a PEUGEOT dealer.
Instrument panel with
monochrome screen
Instrument panel with colour
screen
Coolant temperature indicator light
18-11-2002

Monochrome screen CT
General menu
Press the "MENU" button to access
the general menu and select one of
the following applications :
• navigation guidance (see section "Satellite navigation system"),
• trip computer (see corresponding section),
• directory (see "RT3 audio/tele phone" section),
• telematics (see "RT3 audio/tele phone" section),
• configuration (see corresponding section).
MULTI–FUNCTION
SCREENS
Presentation
Monochrome screen B
This enables the following informa
tion to be displayed:
– the time,
– the date,
– the outside temperature (the °C
symbol flashes when there is a risk
of ice),
– the radio displays,
– the status of the openings (doors, bonnet...),
– the warning (e.g. "Battery charge fault") or information (e.g. "Passen
ger air bag disarmed") messages
displayed temporarily can be
cleared by pressing button 1or 2,
– the trip computer (see correspond ing section).
YOUR 807 IN DETAIL 35
Monochrome screen CT
and colour screen DT
These two systems are controlled by
the
RT3 audio/telephone keypad
and/or by a remote control keypad.
They enable the following informa
tion to be displayed:
– the time,
– the date,
– the outside temperature (a mes sage warns you when there is a
risk of ice),
– the audio source displays (radio, CD, ...),
– the telematic system displays (telephone, services, ...),
– the status of the openings (doors, bonnet, ...),
– the warning messages (e.g. "Fuel level low") and vehicle functions
status messages (e.g. "Passenger
air bag disarmed"), displayed tem
porarily,
– the trip computer display (see cor responding section),
– the satellite navigation system dis plays (see corresponding section).
Note: to enable you to use all of your
system's functions, you have two CD
ROMs: one, "Configuration", con
tains the software and the various
display and spoken information
languages, the other, "Navigation",
contains the satellite navigation
system map data.
18-11-2002

YOUR 807 IN DETAIL
66
Inputting the PIN code Input your PIN code using the alphanumeric keypad and validate by pressing knobGor button #
to access the network. Connection to the network is validated by the appearance of a symbol on
the screen.
Warning: if you make three errors in succession when inputting your PIN code, your SIM card
will be blocked. To unblock it, you will need to input t he PUK code. The PUK code will be suplied
to you by the person selling your SIM card (input of the PUK code allows for 10 errors in suc
cession; after this the SIM card becomes permanently unusable).
Note: the PIN code is required each time the ignition is switched o n, unless the PIN code has
been stored in the memory or protection by PIN code is not activat ed on the SIM card.
Cancelling of PIN code request
In the menu ''Telephone functions'' select''SIM card security'' , then''Process the PIN code'' , then validate the ''Can
cel'' function.
Warning: in this case, do not lose your SIM card. Losing it would mean a nyone who finds it would be able to make unlimited calls.
Telephone function screens
Not in use
This screen indicates the presence of voice messages or minimessages (SMS) no t lis
tened to, the cumulatve time in use since the last zero reset a nd the status of your tele
phone.
In use
This screen indicates the time elapsed since the start of the co nversation, as well as
the number* or name of the person to whom you are speaking (if recorded in the index)
and the status of your telephone.
*If this option and service are available.
18-11-2002

YOUR 807 IN DETAIL101
To be effective, a seat belt
must be tightened as
close to the body as pos
sible.
If the seats are fitted with arm
rests, the lap section of the seat
belt must always pass under the
armrest.
Sitting with your back to the road
while the vehicle is moving is pro
hibited.
Depending on the nature and the
seriousness of the impact, the pre
tensioners may be triggered
before and independently of the air
bags.
In all cases, the air bag warning
light comes on.
Following a collision, have the
system checked by a PEUGEOT
dealer.
The system has been designed to
be fully operational for ten years.
For greater safety, have it checked
by a PEUGEOT dealer after this
period.
POSSIBLE SEAT CONFIGURATIONS
Examples of various arrangements combining pleasure an d practicality:
5 seats
6 seats "Pullman"
18-11-2002

YOUR 807 IN DETAIL101
To be effective, a seat belt
must be tightened as
close to the body as pos
sible.
If the seats are fitted with arm
rests, the lap section of the seat
belt must always pass under the
armrest.
Sitting with your back to the road
while the vehicle is moving is pro
hibited.
Depending on the nature and the
seriousness of the impact, the pre
tensioners may be triggered
before and independently of the air
bags.
In all cases, the air bag warning
light comes on.
Following a collision, have the
system checked by a PEUGEOT
dealer.
The system has been designed to
be fully operational for ten years.
For greater safety, have it checked
by a PEUGEOT dealer after this
period.
POSSIBLE SEAT CONFIGURATIONS
Examples of various arrangements combining pleasure an d practicality:
5 seats
6 seats "Pullman"
18-11-2002

THE KEYS
The keys allow you to switch on the
ignition and to independently operate
the locks on the driver's door and
passenger door, the fuel filler cap,
the glove box, the passenger air bag
disarming switch and the child safety
lock.
Central locking
From the driver's door or passenger
door, the keys allow you to lock,
deadlock or unlock the doors and
tailgate, as well as fold back the
exterior mirrors.
If one of the doors or the tailgate is
open, the central locking does not
work.
The remote control performs the
same functions at a distance.
YOUR 807 IN DETAIL103
The remote control
Version with single locking
Press button
Ato lock the vehicle.
This is confirmed by fixed lighting of
the direction indicators for approxi
mately two seconds. Vehicles fitted with deadlocking
Warning:
deadlocking renders the
internal and external door locking
controls inoperative.
Never leave anyone inside the vehi
cle when the vehicle is deadlocked.
Pressing buttonAdeadlocks the
vehicle. This is confirmed by fixed
lighting of the direction indicators for
approximately two seconds.
A second press on button Awithin
five seconds of deadlocking changes
this to single locking. This is con
firmed by fixed lighting of the direc
tion indicators for two seconds.
Note: the driver operates the dead
locking from inside the vehicle. On
starting the vehicle deadlocking
changes to single locking.
Note: presing button A, in addition to
locking or deadlocking, permits auto
matic closing of the windows and the
sunroof. However, the sunroof stops
in a partially open posiition. Unlocking
/Ventilation
Press button B to unlock the vehicle.
This is confirmed by rapid flashing of
the direction indicators.
A second press on button Awithin
five seconds of deadlocking opens
the windows.
Note : if the vehicle is locked and
unlocking is activated inadvertently,
unless the doors are opened within
30 seconds, the vehicle will lock
automatically.
Opening/Closing the electric
sliding side doors
A long press on button Copens or
closes the rear right door.
A long press on button Dopens or
closes the rear left door.
Note : this press unlocks the vehicle
before opening the corresponding
door.
Folding/opening out the key
To tuck away the key blade, press
button E, then fold it down into the
remote control module.
To open out the key, press button E.
18-11-2002

Changing the battery
of the remote control
The information "battery flat" is given
by an audible signal accompanied by
the message "Remote control bat
tery low" on the multi–function dis
play.
To replace the battery, unclip the
casing using a coin at the ring
(CR1620/3 volt battery).
If the remote control does not work
after the battery has been changed,
re programme the remote control.
Programming the remote
control
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again. CONFIDENTIAL CARD
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film, which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.
Key in ignition
The message
"Key in ignition" on
the multi–function display, accompa
nied by a buzzer on opening the
driver's door, indicates that the key
has been left in the ignition.
YOUR 807 IN DETAIL
104
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore
prevents starting of the vehicle by
anyone who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly,
the message "Antitheft
device fault" appears on the
multi–function display, accompanied
by an audible signal.
WARNING : your vehicle is no
longer protected.
Contact a PEUGEOT dealer as soon
as possible.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park :
 press button A. The courtesy
lights come on and the direction
indicators flash for a few seconds.
18-11-2002

Changing the battery
of the remote control
The information "battery flat" is given
by an audible signal accompanied by
the message "Remote control bat
tery low" on the multi–function dis
play.
To replace the battery, unclip the
casing using a coin at the ring
(CR1620/3 volt battery).
If the remote control does not work
after the battery has been changed,
re programme the remote control.
Programming the remote
control
 Switch off the ignition.
 Switch the ignition on again.
 Press button Aimmediately.
 Switch off the ignition and remove
the remote control key from the
ignition lock. The remote control is
now working again. CONFIDENTIAL CARD
The confidential card contains the
identification code necessary for any
work carried out by a PEUGEOT
dealer on the system. This code is
hidden by a film, which should be
removed only if necessary.
Keep your card in a safe place,
never inside the vehicle.
Key in ignition
The message
"Key in ignition" on
the multi–function display, accompa
nied by a buzzer on opening the
driver's door, indicates that the key
has been left in the ignition.
YOUR 807 IN DETAIL
104
ELECTRONIC ENGINE
IMMOBILISER
This locks the engine control system
a few moments after the ignition has
been switched off and therefore
prevents starting of the vehicle by
anyone who does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
is recognised and starting is possi
ble.
If the system does not function
correctly,
the message "Antitheft
device fault" appears on the
multi–function display, accompanied
by an audible signal.
WARNING : your vehicle is no
longer protected.
Contact a PEUGEOT dealer as soon
as possible.
Locating your vehicle
To locate your vehicle, if you have
locked it, in a car park :
 press button A. The courtesy
lights come on and the direction
indicators flash for a few seconds.
18-11-2002

THE ALARM
This provides two types of protection:
– exterior protection: it sounds if adoor, the tailgate, the bonnet or a
sunroof is opened.
– interior protection: it sounds if the volume inside the passenger com
partment changes (breaking of a
window or a movement inside the
vehicle).
Setting the alarm  Switch off the ignition and get out
of the vehicle.
 Set the alarm within five minutes
of getting out of the vehicle, by
locking or deadlocking using the
remote control (the red indicator
light, located in the centre of the
fascia and visible from the out
side, flashes once per second). Note:
if you wish to lock your vehicle
without setting the alarm, use the
door lock.
When the alarm is triggered, the
siren sounds and the direction indi
cator lights flash for thirty seconds.
After triggering, the alarm remains
set.
Warning: if the alarm has been trig
gered ten times in succession, on
the eleventh time it becomes inac
tive.
Note: if the red warning light, located
in the centre of the fascia, flashes
rapidly, the alarm has been triggered
while you were away from your vehi
cle. To stop it flashing, insert the
remote control key and switch on the
ignition.
Disarming
Unlock the vehicle with the remote
control key (the red indicator light,
located in the centre of the fascia,
goes out).
To set the alarm with exterior
protection only
If, while you are away from the vehi
cle, you wish to leave a window
partially open or a pet inside the
vehicle, you should choose exterior
protection only.
 Close the sunroofs, 
Switch off the ignition,
 In the next ten seconds, press
button A, located on the lefthand
side of the fascia, until the red
indicator light is on continuously,
 Get out of the vehicle,
 Within the next five minutes, set
the alarm by locking or deadlock
ing using the remote control (the
red indicator light, located in the
centre of the fascia, flashes once
a second).
Note: when the alarm is set but the
remote control does not operate:
 Unlock the doors with the key and
open the door. The alarm is
triggered.
 Switch on the ignition in the next
ten seconds. The alarm is dis
armed.
Incorrect operation
When the ignition is switched on, if
the red indicator light, located in the
centre of the fascia, comes on for ten
seconds, there is a fault in the siren
connection.
Contact a PEUGEOT dealer to have
the system checked.
Do not make any modifi
cations to the alarm sys
tem as this could cause
faults.
YOUR 807 IN DETAIL
106
18-11-2002